Harley-Davidson Style Rocker Cover Assemblies installation Instructions

0

Filed Under (Harley Davidson) by admin on 27-10-2010

download
Installation 1. Wash motorcycle, taking care to remove sand and other abrasive debris from engine and area of frame around engine. Remove battery, gas tanks, and all parts required to access original rocker covers. Remove top and center sections of OEM rocker housings. Refer to authorized Harley-Davidson Service Manual as necessary. WARNING – Sparks from motorcycle electrical system can ignite gasoline fumes. To prevent sparks as well as prevent electric starter from becoming engaged inadvertently and causing personal injury, disconnect battery and remove from motorcycle before proceeding. WARNING – Gasoline is toxic when fumes inhaled, extremely flammable, and explosive under certain conditions. Do not smoke around gasoline, and perform installation in a well ventilated area away from sparks and open flame. 2. Remove pushrod cover retainer clips for front cylinder and collapse covers. Remove sparkplugs and rotate engine to place pushrods at lowest point on cam with front piston at TDC on compression stroke. Referring to Harley-Davidson Service Manual as necessary, remove rocker assemblies, pushrods and lower rocker cover from front cylinder head.
3 Picture 3 Picture 4 Right Left Rocker shaft reliefs must align with these holes. NOTE – Observe correct location of pushrods. S&S pushrod kits have longest pushrod for front exhaust, next longest for rear exhaust, shortest for rear intake, and remaining one for front intake. Remove all traces of old rocker housing gaskets from cylinder head, taking care to contain debris. CAUTION – Debris such as gasket material can interfere with oil circulation resulting in engine damage not covered under warranty. 3. Inspect S&S rocker cover assemblies. Remove rough or sharp edges from plain (unchromed) assemblies. Clean all metal parts with solvent. Dry with compressed air and remove any solvent residue with clean, lint free cloth. 4. Install umbrella valves in rocker cover bases. See Picture 1. Valves go in vent ports nearest intake manifold on both front and rear rocker cover bases.

Incoming search terms:

KYMCO Super 8 150 Exhaust System with M-2 Canister Installation Instructions

0

Filed Under (Kymco) by admin on 26-10-2010

download
1.*Make*sure*the*bike*is*completely*cool*before*starting* the*installation.*Make*sure*the*bike*is*secure*on*a* centerstand*or*ideally*a*service*lift. 2.*Remove*OEM*exhaust*assembly. 3.*Attach*supplied*muffler*hanger*bracket*using*the* supplied*flange*bolts*and*tighten*to*15lbs-ft. 4.*Attach*TBR*header*to*muffler*using*the*X-ring*and*4* 6x14mm*bolts*with*lock*washers*provided,*leave*loose* for*now. 5.*Install*TBR*exhaust*to*scooter*keeping*the*OEM*exhaust* gasket*between*header*and*cylinder*head. 6.*Slide*rubber*lined*muffler*clamp*over*muffler*assembly* and*secure*to*bracket*using*supplied*8x20mm*bolt*and* nut. 7 .*Check*muffler*alignment*and*tighten*header*nuts*then* X-ring*bolts*and*finally*muffler*clamp*bolt. 8.*Before*you*run*the*bike,*clean*off*all*fingerprints*and* dirt,*as*any*oily*residue*will*etch*the*metal*and*become* somewhat*permanent*when*the*system*gets*hot.*Run* the*bike*and*enjoy.*It*is*normal*for*some*white*smoke*to* appear*the*first*time*you*start*the*bike.*This*is*packing/ manufacturing*oil*from*inside*the*pipe*burning*off.* Check*for*gaps*or*leaks.*If*you*find*a*leak,*a*little*high* temperature*silicon*sealant*should*fix*it.*After*50*to*100* miles,*recheck*all*fasteners*for*tightness. Qty.*Description* Part*Number 1* Muffler*Canister*M-2** Varies 1* Header* 005-27401H 1* Muffler*Clamp* Varies 1* HARDWARE*KIT* 005-274-3 2* *X-Ring* (half)* 005-7-2-3 1* *Long*Muffler*Mounting*Bracket* 005-274-B 1* *8mm*Flange*Nut* 005-FN8

2004-2007 Kawasaki STX-15F Supercharger Kit installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
ENGINE REMOVAL: 1. Turn ignition off, remove lanyard, disconnect battery cables and remove battery. 2. Remove engine following steps outlined in section 7 of Kawasaki service manual. NOTE: Replace oil filter if engine was run previously. Please recycle used oil and oil filter. NOTE: Clear an area on a sturdy workbench or heavy-duty cart to place engine after removal. Be sure to carefully place engine on a smooth surface so as not to damage oil pan. It is recommended that you have assistance for the engine removal process. 3. Replace stock pistons, rings, piston pins, clips, cylinder head gasket and cylinder base gasket with supplied forged pistons, rings, piston pins, clips, cylinder head gasket and cylinder base gasket following the steps outlined in section 6 of the Kawasaki service manual. NOTE: This is an involved process requiring advanced mechanical skills and 4-stroke engine experience. DO NOT ATTEMPT if you are not mechanically inclined or familiar with 4-stroke engines. 4. Remove OE crankshaft coupler and discard. 5. Locate boss on PTO housing just above crankshaft. Cut off at a 45° angle. (See page 1 of Installation Images) NOTE: Cover end of crankshaft. Thoroughly clean engine afterwards. EXHAUST SYSTEM MODIFICATIONS: 6. Inside hull under rear grab handle remove air inlet tubes. Disconnect hoses for stock bilge pick-ups from breather fittings. (see illustration #1) 7. Remove exhaust hose connecting primary muffler (left water box) to secondary muffler (right water box). Disconnect remaining hoses from breather fittings. Remove exhaust hose connecting secondary water box to exhaust outlet. (see illustration #2) NOTE: Retain hose clamps. 8. Remove section of foam between top deck and pump area and discard. 9. At rear of hull remove and discard plastic exhaust outlet nozzle. Remove exhaust outlet, cut 5-3/4″ from end of flange and weld a bead around modified end of exhaust outlet. (see illustration #3) NOTE: Sand or file edge after modifying. 10. Install one supplied silicone coupler onto modified exhaust outlet and secure using OE hose clamp. (see illustration #4) Install exhaust outlet into hull and secure using stock hardware. (see illustration #5) NOTE: Be sure rubber gasket is in place between flange and hull. Do not use any sealant. Apply blue Loc-tite to bolts. Do not over tighten bolts. 11. Install supplied billet exhaust outlet tip using supplied hardware. (see illustration #6) NOTE: Apply blue Loc-tite to bolts. Do not over tighten bolts.

Incoming search terms:

Kawasaki KFX KLX 400 Camshafts Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Remove the plug bolt from the back of the cam chain tensioner assembly. It is under pressure from the spring. Remove the spring and pin. Remove the bolts and tensioner assembly from the cylinder. Release the lock on the tensioner assembly and push the tensioner rod into the assembly so that it is fully retracted. Remove the eight 5mm Allen headed bolts that hold the cam caps in place. Remove the cam caps; be aware of the locating dowels in the caps to keep them from falling into the engine. It may be necessary to pry very lightly on the caps to lift them off their dowel pins. Do not use the cam lobe as the pry point. Lift the intake camshaft out of its pocket in the cylinder head casting. Remove the cam chain from the sprocket, set the stock camshaft aside. Lift the exhaust cam out of its pocket in the cylinder head casting and remove the chain from the sprocket. Do not drop the cam chain; dangle it over the side of the engine while keeping slight upward pressure on the chain to maintain its position on the drive sprocket on the crankshaft. Using assembly lube, lube the shim buckets and bearing surfaces for the camshafts in the cylinder head. Set the exhaust camshaft into the cylinder head casting while at the same time fitting the cam chain over the sprocket. Make sure that you keep all the cam chain slack to the back of the engine. Repeat the above process for the intake camshaft. Again, make sure you keep the chain slack to the cam chain tensioner side of the engine. Check to be sure the crankshaft is still at TDC. Check the location of the cam lobes. The camshafts are marked, and preset to 108-degree centers. If the lobes are not where they should be, adjust the positioning of the camshaft by rotating the sprocket one tooth on the chain. Do this until it is in the correct position as before you removed the camshafts. Check the positioning of the crankshaft for the TDC mark

Incoming search terms:

Harley-Davidson V-Rod Destroyer Indy Series Exhaust REMOVAL AND INSTALLATION

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
STOCK EXHAUST SYSTEM REMOVAL (DESTROYER) 1. Remove both collector bolts. 2. Remove nuts from both front and rear exhaust cylinder head flanges using a 13mm socket. 3. If the Racepak is installed, remove both O2 and EGT sensors from the front and rear head pipes. 4. Carefully remove complete exhaust from the motorcycle. STOCK EXHAUST SYSTEM REMOVAL (V-ROD) 5. Loosen clamp bolt at front of the collector using a 13mm socket. 6. Remove muffler bracket bolt using a 13mm wrench. 7. Carefully remove muffler and collector assembly from motorcycle. 8. Remove nuts from both front and rear exhaust cylinder head flanges using a 13mm socket. 9. Carefully remove head pipes from motorcycle. 10. Remove the stock exhaust flanges and circlips from both the front and rear head pipes. If the circlips are bent or twisted they should be replaced, Harley-Davidson part number #65045-01 We also recommend replacing the stock exhaust gaskets, Harley-Davidson part number #65109-01 INDY SERIES EXHAUST SYSTEM INSTALLATION 1. Identify front head pipe #7-8002. Install the stock flange and circlip. Install the exhaust gasket and front header pipe, leaving the flange nuts hand tight. 2. Repeat the above step for the rear head pipe #7-8006. 3. Slip the megaphone/collector assembly onto the head pipes, secure with the four springs supplied using the spring puller tool. 4. Rotate the exhaust so there is adequate clearance in all places. 5. Tighten the cylinder head flange nuts for both the front and rear head pipes. 6. Tighten both the EGT and O2 plugs on the front and rear head pipes. 7. Clean all fingerprints from the exhaust using a contact cleaner (or other non flammable cleaner). Fingerprints will leave stains on the pipe once the motorcycle is started. 8. You are now ready to start the motorcycle.

Incoming search terms:

Incoming search terms: