Harley Davidson DRESSERS TUNED-FLOW SLIP-ON MUFFLERS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 23-03-2012

download
Installing the Tips: 1. Use a long 3/16″ ball drive Allen wrench to remove the two hidden retaining screws. 2. Rotate the tip to the desired position and relocate the retaining screws and lock washers inside the tip. 3. Apply a small amount of anti-seize compound to the threads and tighten to 8 ft./lbs. 4. Check the tip bolts after a brief test ride. Adjusting the Hooker Tuned-Flow® Muffler: 1. Loosen the socket head bolts located in the aluminum ring at the end of the muffler approximately 5 turns using a 3/16″ Allen wrench. Alternate back and forth between each bolt 1/2 turn at a time to keep from binding. 2. Using your fingers, pull the center barrel of the muffler approximately 1/8″ towards the back of the motorcycle and rotate to the desired setting. If warm, use a rag or gloves. 3. By rotating the exhaust barrel and aligning the notch in the barrel with the index marks in the aluminum ring, the power band can be adjusted. The “H” setting will bias the power towards High RPM Horsepower, while the “T” setting will provide more Low RPM Torque. The muffler is infinitely adjustable between these two settings

HARLEY DAVIDSON FAT HANDLEBAR RISER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 22-03-2011

download
INSTALLATION NOTES The upper cup washer (A) must be oriented with the flat side up and the lower cup washer (D) with the flat side down. See Figure 1 for the following procedure. 1. Align the components as shown, and install the risers (2) to the upper fork bracket. The ground wire (G) and the internal tooth lock washer (H) are located on the right side only. Do not tighten the riser mounting screws (I) at this time. 2. If an appropriate Harley-Davidson 1-1/4 inch handlebar has not been installed, install one according to the Instruction Sheet included with the kit, or re-install the handlebar assembly onto the risers. 3. Loosely install riser caps (1) onto the handlebars and risers using four socket head screws (3) as shown. 4. Ensure that the risers stay properly aligned with the handlebar and tighten the riser mounting screws (I) to 50-60 ft-lbs (68-81 Nm) . 5. Adjust handlebar to the desired position, ensure that it is centered on the risers, then, starting with the front screws, tighten the four socket head screws (3) to 12-15 ft-lbs (16- 20 Nm) . 6. Turn the handlebars full right and left. Check that: •The handlebars and triple tree clamps do not contact the fuel tank. •The steering stops function properly. •The wiring and brake line are not pinched or kinked in the steering assembly. •Throttle returns from full open to close at both fork stops. Install proper length brake lines. Incorrect brake line length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00325a) •If you are installing different handlebars, measure the change in distance that will be required from the end of the stock brake line to the brake master cylinder. •Compare this revised length to the brake line provided in your kit. •If the line is more than 2.0 in. (50.8 mm) longer or more than 1.0 in. (25.4 mm) shorter than the above measured distance, see a Harley-Davidson dealer for the correct brake line length

993-192 LED Light, 993-193 Marker Light CHROME RAIL BAR LIGHT INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 28-02-2011

download
Read instructions thoroughly before installing. 1. Place bike on center stand. 2. Place chrome plate on to the desired position on the rail covering both the top and bottom rail with the chrome plate. 3. Insert light into the hole on the chrome plate and attached with brackets, washer and bolts provided in figure 1. Tighten securely. 4. Wire light into bike’s running or brake lights. If adding more than one light, wire lights in series.

HARLEY DAVIDSON FRONT SPEAKER TRIM INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-02-2011

download
Installation NOTE Do not install this product below 60°Fahrenheit or the speaker trim will not adhere properly. NOTE Trim rings cannot be repositioned after initial installation so be certain the trim rings are properly aligned. 1. Gently brush or vacuum each speaker grill to remove any dust or dirt particles. 2. Cut 8 one inch long strips of narrow masking tape. 3. Without removing the adhesive backing, position the trim rings against the speaker grill. 4. Rotate trim rings into desired position and hold in place. 5. See Figure 1. Apply masking tape directly to the speaker grill above and below the trim ring cross bar and on both sides of the center Bar and Shield logo. This will serve as an installation template. 6. Remove trim ring adhesive backing. 7. Align trim ring with the masking tape template and press firmly into place. 8. Remove masking tape template. 9. Allow adhesive to cure for 24 hours before operating the motorcycle

HARLEY DAVIDSON PULLBACK RISER KIT FOR 1.25-INCH HANDLEBARS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
REMOVAL NOTES Cover the fuel tank with clean shop towels to prevent scratching. If replacing the handlebar, refer to the service manual to remove controls, hand levers, handlebar and risers. If only the risers are being replaced, proceed as follows: 1. Remove the two hex head cap screws and split lock- washers on the underside of the upper fork bracket that hold the currently installed risers in place. Discard the screws, but retain the lockwashers for assembly. Retain all additional components from the riser assembly when the screws are removed. 2. Remove and discard the four screws that fasten the currently installed handlebar upper clamp(s) to the risers. Remove and discard the clamp(s). Remove the handlebar from the risers and carefully set the handlebar on the fuel tank. INSTALLATION NOTES See Figure 3. The upper cup washer (A) must be oriented with the flat side up and the lower cup washer (D) with the flat side down. 1. See Figure 3. Align the components as shown, and install the risers (2) to the upper fork bracket. The ground wire (G) and the lock washer (F) are located on the right side only. Do not tighten the riser mounting screws (4) at this time. 2. If an appropriate Harley-Davidson 1-1/4 inch handlebar has not been installed, install one according to the Instruction Sheet included with the kit, or install the handlebar assembly onto the risers. 3. Loosely install riser caps (1) onto the handlebars and risers with the Bar & Shield toward the front of the motorcycle (Figure 1, Item 1). Install four socket head screws (3) with four washers (6). 1 is05253 1. Bar & Shield (install toward front of motorcycle) Figure 1. Bar & Shield on Riser and Cap 4. Check that the risers stay properly aligned with the handlebar and tighten the riser mounting screws following the instructions in the service manual. 5. Adjust handlebar to the desired position, verify that it is centered on the risers, then tighten the front socket head screws (3) to 12-15 ft-lb (16-20 Nm) . There should be no gap at the front of the risers.

HARLEY DAVIDSON LEATHER FUEL TANK PANEL INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
INSTALLATION Softail Models NOTE Generic leather tank panel shown for illustration purposes. 1. Refer to Owner’s manual for removal of seat. 2 3 1 is00927 1. Instrument panel 2. Nut 3. Masking tape Figure 1. Leather Fuel Tank Panel Installed 2. See Figure 1. Remove nut (2) securing instrument panel (1). Gently lift instrument panel up and turn it so stock fuel tank panel front end is uncovered. 3. Place a shop towel under instrument panel and set instrument panel on fuel tank. 4. See Figure 2. Remove lower mounting screw and washer (1) and retain for reinstallation. 5. Lay leather tank panel on tank in desired position. 6. Install screw and washer saved in Step 4 into hole on tank panel. Tighten screw finger tight. 1 is02467 1. Save screw and nut for reinstallation Figure 2. Softail Tank Panel Installs With Original Screw And Nut 7. See Figure 1. Install instrument panel (1) and tighten nut (2) to 8 ft-lb (11 Nm) . 8. Tighten lower mounting screw. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 9. Install seat on the motorcycle by inserting the tab at front of seat into slot at the rear of fuel tank. Secure seat to fender with screw. INSTALLATION FXDWG and FXDC NOTE Generic leather tank panel shown for illustration purposes. 1. Refer to Owner’s manual for removal of seat. 2. 1993-2003 Models: Figure 1. Remove nut (2) securing instrument panel (1). Gently lift instrument panel up and turn it so stock fuel tank panel front end is uncovered. 2004 and later Models: See Figure 4.

YAMAHA ROAD STAR HANDLEBAR RISERS INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 29-01-2011

download
1. Place a blanket folded several times over the fuel tank to prevent any damage during the installation of the risers. Loosen the two 19mm riser mounting nuts located on the bottom side of the upper steering head. Pry out the chrome plugs from the heads of the four handlebar top clamp bolts using a knife blade. Loosen the four handlebar top clamp 6mm socket head screws. 2. It will help having a second person to hold the handlebars while you change the risers. Remove the four screws from the clamps and then the clamps. Pull the handlebars up off the risers, pull them back and rest them on top of the blanket. 3. Remove the nuts from the bottom of the risers and remove the risers. Insert the two supplied spacer tubes into the riser mounting holes on the upper steering head. Using the bolts, lock washers and washers supplied install the new risers making the bolts finger tight only. (Take care not to scratch the top surface of the upper steering head while installing the new risers.) 4. Place the handlebars back up onto the new risers. Reinstall the top clamps using the four socket head screws removed earlier. Set the height of the handlebars to the desired position, tighten the front bolts first and then the rear securely. (15-18 ft. lbs. There should be no gap between the riser and clamp at the front side.) Tighten the two riser mounting bolts securely. (20-25 ft. lbs.) 5. Turn the handlebars all the way to the left and then right checking for any pulling or binding of the wires, hoses or cables. Also check that the throttle returns freely on it’s own

HONDA VT 1100 HIGHWAY MOUNTS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Remove the parts supplied from the package and lay them out in front of you. Remove the screws from the mounts and clamps. See photo (1), notice that the two clamp halves (1A) and the two arms (1B) are the same. Notice that the two mounts (1C) are different and are machined at opposite angles. The mounts (1C) can be installed facing forward to the front of the bike as shown in photo (1) or facing to the rear of the bike as shown in photo (2) depending on how far forward you want the pegs to be located. 2. Starting on the right side choose which way you want the mount to face. Hold one of the mounts up against the frame tube. Hold one of the arms up against the mount where it bolts together. The arm should be horizontal or level when the bike is sitting up straight. If not use the mount with the opposite angle. Next while still holding the mount in place at the desired location place one of the clamps behind the mount and start the screws. Snug the screws only leaving them loose enough to make further adjustments later. Next Bolt one of the pegs loosely to the arm as shown in photo (2). Notice that there are eight dowel pin holes on the mount and seven on the back side of the arm allowing 56 possible angles or positions for the arm to be set at. Holding the arm/peg assembly up to the mount select the desired position for the arm and place one of the dowel pins supplied into the nearest set of holes on the mount and arm. Bolt the arm/peg assembly to the mount using one of the large button head Allen screws and a washer provided. Once you have the arm close to where you want it you can make fine adjustments by removing the large Allen screw, removing the arm and moving the dowel pin to the next hole in the mount. Moving the pin clockwise one hole will rotate the arm in the opposite direction approximately ½”. Likewise moving the pin counter clockwise will rotate the arm in the opposite direction. 3. Repeat this procedure on the left side. Sit on the bike. Place your feet on the highway pegs and verify that you have them set at the most comfortable position for you and that they are set the same on both sides. Tighten all bolts and screws securely

TRIUMPH AMERICA AND SPEEDMASTER HANDLEBAR RISERS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-01-2011

download
1. Place a blanket folded several times over the fuel tank to help prevent any damage during the installation of the risers. Loosen the two 14mm riser mounting nuts located on the bottom side of the upper steering head. Loosen the four handlebar top clamp 6mm socket head screws. 2. It will help having a second person to hold the handlebars while you change the risers. Remove the four screws from the clamps and then remove the clamps. Pull the handlebars up off the risers, pull them back and rest them on top of the blanket. 3. Remove the nuts from the bottom of the risers and remove the risers carefully without allowing the risers to rotate, as this will scratch the clear coating on the upper steering head. Using the bolts, lock washers and washers supplied install the new risers making the bolts finger tight only. (NOTE; again, take care not to allow the risers to rotate as this will scratch the clear coating on the upper steering head). 4. Place the handlebars back up onto the new risers. Install the new top clamps supplied using the four M8 X 30mm socket head screws supplied. Set the height of the handlebars to the desired position, tighten the front bolts first and then the rear securely. (15-18 ft. lbs.) (There should be no gap between the riser and clamp at the front side) Tighten the two riser mounting bolts securely. (20-25 ft. lbs.). 5. Turn the handlebars all the way to the left and then right checking for any pulling or binding of the wires, hoses or cables. YOU MUST! Check to see that the throttle returns freely on its own when the handlebars are at full left and full right turn THIS STEP IS VERY IMPORTANT FOR OBVIOUS SAFETY REASONS! If you have a windshield installed it may be necessary to reroute the throttle cables, wires or hoses around the other side of the windshields mounting hardware to obtain adequate free play and free throttle return. You may also wish to remove the plastic clips or cable tie which secure the wiring to the handlebars and secure them to the brake hose and clutch cable (not the throttle cables) for a cleaner appearance

Incoming search terms:

Triumph Rocket III Touring HANDLEBAR RISERS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-01-2011

download
1. Place a blanket folded several times over the fuel tank to help prevent any damage during the installation of the risers. Using a small screwdriver pry out the plastic caps covering the handlebar clamp bolts. 2. Reroute the clutch cable behind the steering head as follows. Remove the clutch cable from the lever and perch. To do this first loosen the cable adjuster lock nut and then the adjuster as far as possible to give its maximum free play. Align their slots with the slot in the perch so that the cable may slide out. Standing in front of the handlebars grasp the clutch cable firmly trying to pull it out of the adjuster with one hand while pulling in the lever with the other hand. Now release the lever rapidly. Repeat several times if needed while keeping outward tension on the cable until the cable is out of the adjuster then slide it out thru the slots and remove the cable end from the lever. Reroute the clutch cable behind the steering head this will allow the additional slack needed when moving the handlebars back with the new risers (see photo). Replace the cable into the perch in the same manner. 3. It will help having a second person to hold the handlebars while you change the risers. Remove the four Allen bolts from the clamps and then remove the clamps. Pull the handlebars up off the risers, pull them back and rest them on top of the blanket. 4. Remove the Allen bolts from the center of the risers while holding the 14mm nut on the bottom side of the steering head with a wrench. Remove the risers leaving the large washer on the top side of the steering head in place. Using the bolts and lock washers supplied and the original heavy or thick washer install the new risers making the bolts finger tight only. 5. Place the handlebars back up onto the new risers. Install the new top clamps supplied using the four Allen bolts remover earlier. Set the height of the handlebars to the desired position, tighten the front bolts first and then the rear securely. (15-18 ft. lbs.) (There should be no gap between the riser and clamp at the front side) Tighten the two riser mounting bolts securely. (20-25 ft. lbs.). Replace the plastic bolt caps.