HONDA CBR 1000 RR ALFANO systems Installation

0

Filed Under (Honda) by admin on 26-11-2011

download
If the sensor doesn’t start to the passage on the magnetic field, use one or several spacers to bring the sensor closer to the ground. – When fixing the cable with nylon tighten-cables, take care to move this one most possible away of the exhaust Fix the magnetic support (supplied) on one of the arms of the disc brake support with a nylon tighten-cable (see photos). Fix it on the narrowest part of the arm. – With a scorer, draw a feature on the mudguard in front of the magnetic support n this case, install the speed sensor to « 90° ». – Put down the mudguard and fix the speed sensor and its cable with nylon tighten-cables. For that to make, pierce holes of diameter 3mm (to see photos)

Toyota Camry L4 – 2.4L 2004 Brakes and Traction Control Disc Brake System Service and Repair

0

Filed Under (Toyota Manuals) by admin on 24-05-2011

Download
REMOVE FRONT DISC BRAKE CYLINDER SLIDE BUSH 10. Remove the cylinder slide bush from the cylinder slide pin.
a. REMOVE FRONT DISC BRAKE BUSH DUST BOOT 11. Remove the 2 bush dust boots from the disc brake cylinder mounting. a. REMOVE FRONT DISC BRAKE CYLINDER MOUNTING LH 12. Remove the 2 bolts and disc brake cylinder mounting LH. a. REMOVE CYLINDER BOOT 13. Using a screwdriver, remove the set ring and cylinder boot.
a. REMOVE FRONT DISC BRAKE PISTON 14. Place a piece of cloth or similar, between the piston and the disc brake cylinder. a. Use compressed air to remove the piston from the disc brake cylinder. CAUTION: Do not place
your fingers in front of the piston when using compressed air. NOTICE: Do not spatter the brake fluid

HARLEY DAVIDSON DUAL DISC FRONT BRAKE KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
This kit is designed for installation on the following models which have original equipment 39mm front fork tubes (including chromed tubes) and 19-in. cast-aluminum front wheels: • 2000 – 2003 XLH 883, XLH 883 Hugger and XLH 1200 • 2000 – 2003 FXD (Super Glide) This kit can also be installed on the above XLH and FXD models which have original equipment 39mm front fork tubes and 19-in. laced front wheels only after one of the following procedures is performed: • The original single-flange hub of the 19-in laced front wheel is replaced with a new double-flange hub (H-D Part No. 43629-00), (sold separately) which will accept the second brake disc. OR • The original 19-in. laced front wheel assembly, which has a single-flange hub, is replaced with a new 19-in. laced front wheel assembly (H-D Part No. 43579-00), (sold separately) which has a double-flange hub designed to accept the second brake disc. See the Service Parts Illustration for a list of the contents included in this kit. This kit does not include the front brake line required for a dual disc system; the brake line must be purchased separately as follows: • For XLH 883 motorcycle equipped with low-rise (flat) handlebars, order dual disc brake line H-D Part No. 45148-96. • For XLH 883 Hugger, XLH 1200, and FXD Super Glide models with “buckhorn” (pull-back) handlebars, order dual disc brake line H-D Part No. 45111-96. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) Brakes are a critical safety component. Contact a Harley- Davidson dealer for brake repair or replacement. Improperly serviced brakes can adversely affect brake performance, which could result in death or serious injury. (00054a) Removal and Disassembly – Front Brake System NOTE A Service Manual for your motorcycle is available at your Harley-Davidson Dealer. 1. Block motorcycle underneath frame so that front wheel is raised off the ground slightly. 2. Remove original front brake caliper from left side of front fork according to appropriate Service Manual procedures. Let caliper hang loose on brake line. Save all components and fasteners for reinstallation. NOTE Do not operate the front brake lever with the front caliper removed because the piston may be forced from the caliper. Reseating the piston requires disassembly of the caliper . 3. Remove socket head screw which secures a clamp (retains front brake line) to underside of front fork lower bracket (lower triple clamp). Discard clamp and screw. 4. Remove screw, lockwasher, and clamp which secure front brake line to right rear side of front fork upper bracket (upper triple clamp). Save all components for reinstallation. 5. Remove right mirror and, if applicable, right turn signal lamp assembly from original front brake master cylinder casting. Save all components and fasteners for reinstalla- tion.

Incoming search terms:

MZ 125 SXJSM Repair Manual

0

Filed Under (MZ) by admin on 18-11-2010

download
Front suspension · Design Telescopic fork · Spring travel 220 mm Rear suspension · Design long swinging fork · Spring travel/adjustment 220 mm/adjustable spring base Steering bearing Deep groove ball bearing Clutch lever and throttle twist grip · Play in the clutch lever 3-5 mmattheendofthe clutch · Play in throttle Bowdencable 2-3 mmatthetwist grip flange Wheels – spoked wheels Variant MZ125 8X Variant MZ125 8M Front tire 90/90 -21 110170-17 Tire pressure 190 kPa/1,9 bar/28 psi 180 kPal1,8 bar/26 psi Rim size 1.85×21 3.00 x17 Rim wobble limit vertical 0,5mm 0,5mm side 0,5mm 0,5mm Rear tire 120/80 – 18 130170-17 TIre pressure (value at perm. axle load) 200 (250) kPa/2 (2,5) bar/29 (36) psi 230 (260) kPal2,3 (2,6) bar/33 (66) psi Rim size 2.50 x18 3.50 x17 Rim wobble limit vertical 0,5mm 0,5mm side 0,5mm 0,5mm Front wheel brake · Design hydraulic single-disc brake with a two-piston floating caliper I and manually operated cylinder · Outside diameterxplate thickness 280x4mm · Thickness of the brake pad 5,Omm · Wear limit <2,Omm · Main brake cylinder inside diameter 11 mm · Brake caliper cylinder inside diameter 2×25,4 mm · Brake fluid DOT4 Rear wheel brake · Design hydraulic single-disc brake with a two-piston floating caliper and manually operated cylinder · Outside diameterxplate thickness 220x4mm · Thickness of the brake pad (wear limit) 5,Omm · Wear limit <2,Omm · Main brake cylinder inside diameter 13mm · Brake caliper cylinder inside diameter 2x 25,4mm · Brake fluid DOT4 Brake level and brake pedal · Play in brake lever 2-5 mmattheendofthe brake lever · Position of brake pedal 25 mmunderthe footrest rubber surface

VESPA GTS SUPER SPORT 300 Technical specification

0

Filed Under (Vespa) by admin on 11-11-2010

download
Engine Single-cylinder, catalysed, QUASAR 4 stroke, 4 valve electronic injection Capacity 278cc Power 16.4 Kw / 7500 rpm Max Torque 22Nm / 6500 rpm Cooling Liquid Starter Electric Transmission Automatic Twist and Go Front Suspension Single arm, dual chamber hydraulic shock absorber with coaxial spring Rear Suspension Two dual effect shock absorbers with adjustable preload Front Brake ø 220mm disc brake Rear Brake ø 220mm disc brake Front Tyre Tubeless 120/70-12″ Rear Tyre Tubeless 130/70-12″ Running weight 158kg Length/Width/Height 2230mm / 755mm / 1170mm Fuel Tank Capacity 9 litres Emissions Euro 3 Accessories • Flyscreen (clear or tinted) • Windscreen • 42 litre Top Box Kit • Chrome Front & Rear Rack • Chrome Bumper Guard • Chrome Rear Side Protection • Alarm, Chain Lock, Vehicle Cover, Leg Cover Colours Grigio Titanio

VESPA GE 50cc specification

0

Filed Under (Vespa) by admin on 11-11-2010

download
Engine Single-cylinder LEADER 4 stroke Capacity 124cc Power 7.65 Kw / 8250 rpm Max Torque 9.6 Nm / 7250 rpm Cooling Forced Air Starter Electric and kick starter Transmission Automatic Twist and Go Front Suspension Single arm link with coil spring and double hydraulic shock absorber Rear Suspension Coil spring and double hydraulic shock absorber Front Brake ø 200mm disc brake Rear Brake ø 110mm drum brake Front Tyre Tubeless 110/70 – 11″ Rear Tyre Tubeless 120/70 – 10″ Running weight 114kg Length/Width/Height 1770mm / 740mm / 1140mm Fuel Tank Capacity 8.5 litres Emissions Euro 3 Accessories • Windscreen • 32 litre Top Box Kit • Chrome Front & Rear Rack • Chrome Bumper Guard • Chrome Rear Side Protection • Sticker Kits – 6 designs available • Alarm, Chain Lock, Vehicle Cover, Leg Cover Colours Bianco/Azzurro, Bianco/Rosso