Harley Davidson Shift leverbracket INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-03-2012

download
Installation of any parts should be performed by a qualified, trained mechanic. • All parts included in the Rocker Boards™Conversion Kit are intended to be used as sold. Modification of any part will void all warranties. • Installation should be performed on a motorcycle that is completely cool to avoid burns or other injuries. • Refer to a specific authorized Harley-Davidson service manual for correct disassembly and reassembly procedures for any parts that need to be removed to facilitate installation. • Motorcycle exhaust fumes are toxic and poisonous and must not be inhaled. Always run motorcycle in a well-ventilated area. • Do not perform any installation steps under the influence of alcohol, drugs, or if feeling fatigued. Warranty Briggs Made Cycle Parts, Inc. Rocker Boards™and all parts included in the conversion kit are warranted to the original purchaser to be free of manufacturing defects in materials and workmanship for a period of one (1) year from the original date of purchase. Any part that fails to conform to these conditions, will be repaired or replaced at the discretion of Briggs Made Cycle Parts, Inc. upon receipt of the defective part within the one year warranty period. In the event a part has been rendered defective, Briggs Made Cycle Parts, Inc. must be notified prior to the return of the defective part. Briggs Made Cycle Parts, Inc. will not be liable for any consequential or incidental damages resulting from the failure of any part, the breach of any warranties, the failure to deliver, delay in delivery or any other breach of duty between Briggs Made Cycle Parts, Inc. and a customer

Harley Davidson Road King Lightbar installation manual

0

Filed Under (Harley Davidson) by admin on 06-03-2012

download
This product is designed to mount in the lowest, visible section of the motorcycle windshield. 1. Install the 3 housing edge seals (1 long seal and 2 short seals) onto the lightbar as shown (Fig. 1). Make sure that the seal is oriented so that the lip curls inward (Fig 2). 2. Remove the 3 screws shown from the upper section of the windscreen (Fig. 3.). CAUTION! DO NOT LOOK DIRECTLY AT THESE LED’SWHILE THEY ARE ON. MOMENTARY BLINDNESS AND/OR EYE DAMAGE COULD RESULT! IMPORTANT WARNING! WARNING! All customer supplied W ires that connect to the positive terminal of the battery must be sized to supply at least 125% of the maximum operating current and FUSED at the battery to carry that load. DO NOT USE CIRCUIT BREAKERS WITH THIS PRODUCT! Fig. 1 Fig. 4 Fig. 3 Fig. 2 3. Position the lightbar into its mounting position behind the windscreen. When properly positioned, the holes in the lightbar mounting tabs will be aligned with the vacant holes through the windscreen. 4. Using the mounting hardware included with the lightbar, secure the lightbar to the windscreen assembly. 5. Route the wires to their respective destinations (Fig. 4). It is left to the installation technician’s discretion to select a path for these wires that will both protect them from possible damage and not interfere with the operation of any other vehicle components or equipment

Harley-Davidson Electra Glide LED Motorcycle Lightbar Installation Guide

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
Mounting IMPORTANT! The lightbar should be located a minimum of 16″ from any radio antennas! This product is designed to mount in the lowest, visable section of the motorcycle windshield. The mounting procedure requires removal of the front facia panel of the motorcycle. 1. Remove the 3 screws along the base of the windshield from the upper section of the faring facia panel. 2. Remove the 4 remaining screws (shown above) that secure the facia panel to the faring. With these screws removed, the facia and windshield can now be removed from the motorcycle faring. 3. Position the lightbar into its mounting position. The base of the lightbar fits onto the three screw bosses used by the screws removed in step 1. 4. With the facia panel removed, the lightbar should now be wired. 5. Route the wires to their respective destinations. It is left to the installation technician’s discretion to select a path for these wires that will both protect them from possible damage and not interfere with the operation of any other vehicle components or equipment. 6. Using the original hardware removed in steps 1 & 2, remount the faring and windshield according to the motorcycle manufacturers service manual