1994 HARLEY DAVIDSON FXD (DYNA) PASSENGER FLOOR BOARDS AND RELOCATION ARMS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-04-2012

download
1. Beginning on the RIGHT side, use a 9/16″ wrench to remove the bolt from the back of the passenger peg mount. Remove entire peg assembly. 2. Remove the new floorboards and mounts from their packaging. Notice the Left and Right markings on the backside of the floorboard mounting plates. 3. Install the supplied Right floorboard support (the longer one) with the round mounting face for the floorboard towards the upper-right using the supplied 7/16 x 1 º” long bolt. Apply blue Loctite to the threads. Insert the bolt from the backside where the original peg was mounted. Use a 5/8″ wrench & tighten securely. Note: If also installing with optional Relocation Arms (#FXD005-5) skip step 4 and go onto step 5. 4. Installation of Right Floorboard only. There are two sets of alignment holes on the floorboard support. Insert two of the four dowel-pins into the dowel pinholes at six and twelve o’clock. Place the right floorboard onto the mount and dowel pins so that it is parallel (horizontal) to the ground. Insert the supplied 5/16 X 1″ socket head cap screw through the floorboard mount & thread into the floorboard support. Use a º” hex key wrench & tighten securely. 5. Remove Right Floorboard – Installation of Right Floorboard with Relocation Arm. There are two sets of alignment holes on the floorboard support. Insert two of the four dowel pins into the dowel holes 180 degrees apart. Notice the L & R markings on the backside of the relocation arms. Install the Right relocation arm so marking (R) is facing inward and the threaded hole is facing toward the front of the motorcycle. There are two sets of alignment holes on the relocation arms. Place the arm onto the mount (Match dowel pin holes) in desired upper or lower position. Insert the supplied 5/16 X 1″ socket head cap screw through the relocation arm & thread into the floorboard support. Use a º” hex key wrench & tighten securely. 6. At the other end of the relocation arm there are two sets of alignment holes. Insert two of the supplied dowel pins into the set of dowel pin holes 180 degrees apart that will allow the floorboard to be horizontal or parallel to the ground. Insert the supplied 5/16 X 3/4″ socket head cap screw through the floorboard mount & thread into the link arm. Use a º” hex key wrench & tighten securely.

Incoming search terms:

Yamaha YZ 250F Camshafts REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 30-12-2011

download
Remove the 4 bolts that hold the exhaust cam cap in place, lift the cam cap off. It may be necessary to pry very lightly on the cap to lift it off its dowel pins. Do not use the cam lobes as the pry point. Be careful not to drop the dowels and also be careful to not lose the half moon shaped retainer for the bearing under the cam cap. Remove the 6 bolts that hold the intake camshaft cap and lift the cam cap off the camshaft, again, be careful to not drop the retainer or dowels. Lift the intake camshaft out of its pocket in the cylinder head casting. Remove the cam chain from the sprocket, set the stock camshaft aside. Lift the exhaust cam out of its pocket in the cylinder head casting and remove the chain from the sprocket. Do not drop the cam chain, dangle it over the side of the engine while keeping slight upward pressure on the chain to maintain its position on the drive sprocket on the crankshaft. Fit the half moon shaped retainers in the grooves of the Hot Cams camshaft bearings to ensure good fit, set retainers aside for the time. Using assembly lube, lube the shim buckets, bearing surfaces for the camshafts in the cylinder head, and pack some in the camshaft bearings. Set the exhaust cam into the cylinder head casting while at the same time fitting the cam chain over the sprocket. Make sure that you keep all the cam chain slack to the back of the engine. The cam chain pulls the camshaft sprockets in a counter clockwise direction and the slack of the chain must be kept on the cam chain tensioner side of the engine. The exhaust cam has two timing marks on it. When correctly installed one mark will be at the 9 o’clock position and the other mark will be at the 12 o’clock position. When correctly timed the mark at 9 o’clock will be aligned with the valve cover gasket surface. Repeat the above process for the intake camshaft. Again, make sure you keep the chain slack to the cam chain tensioner side of the engine. Check to be sure the crankshaft is still at TDC. The intake cam has two timing marks also. One at 12 o’clock and the other at 3 o’clock. When both cams are installed correctly, the valve cover gasket surface will form a straight line through the exhaust timing mark at 9 o’clock and the intake timing mark at 3 o’clock

Incoming search terms:

HONDA 420 RANCHER 2×4/4×4 2007-2009 CLUTCH KIT INSTRUCTIONS

0

Filed Under (Honda) by admin on 22-12-2011

download
Remove key from the ignition switch. Remove the side panels from both sides. Remove both foot wells. 2. Drain coolant. Remove the oil drain plug from the motor; if you carefully drain it into a clean container you should be able to reuse it. 3. Disconnect shift motor (on electric shift models only). Remove coolant hoses. 4. Remove the bolts that mount the front differential to the frame, no other parts need to be removed. Carefully slide the front differential towards the front of the machine; you might need to lift up slightly to get the differential to move. Remove the drive shaft. Remove o-ring on output shaft (on motor). 5. Remove the fuel pump. 6. Loosen the front crankcase cover bolts, keep track of each bolt length and location. Slowly remove the crankcase cover. Carefully watch for o-ring shims and dowel pins that may fall out. 7. Unstake the nut holding the clutch on and remove nut. Using Honda tool #07933-HB3000A thread the large part of the tool into the center of the clutch. Tighten the center bolt on the tool while holding the large part of the tool with a wrench. This will pull the clutch off the machine. Place the clutch on a clean work surface. EPI performance.com
8. Using the c-clamps push down slightly on the outside cover and remove the four e-clips. Keeping track of which way they come off, remove the round metal plates one at a time. This will allow you to see the complete spring. Remove one end of each spring using a spring tool or needle nose pliers and then remove springs. Install the EPI springs by inserting the spring into the outer edge first. Using a spring tool or pliers (45 degree bent pliers work well) pull on the spring and insert the end into the hole. Install the metal plates and the e-clips. If you can’t get the plates to sit flat make sure each clutch arm is flat against the bottom plate of the clutch. Occasionally when you put the springs on, the clutch arms will pop up. Slide the clutch into the machine. The Sprague clutch is marked “outside” when installing make sure this is facing out. Torque clutch nut to 87 ft/lbs. 9. Clean the gasket surface on the motor and on the cover. Put a thin layer of Honda Bond or Yamabond semi-drying liquid gasket (or something similar as long as it is semi-drying) on the crankcase cover. Carefully install crankcase cover, do not force cover on. Torque bolts to 9 ft/lbs. 10. Install the fuel pump. 11. Install the o-ring on the output shaft (on motor) and install the drive shaft. Carefully slide the front differential back into place and mount to the frame. Install the coolant hoses. Refill your engine coolant to the proper level according to your owner’s manual. 12. Install the oil drain plug. Refill your engine to the proper level according to your owner’s manual. You can reuse your oil if it is clean and was drained into a clean container. Only use manufactures recommended oil. 13. Be sure to double check coolant and oil levels and to look for any leaks after the machine has run for a few minutes. 14. Go out and ride your machine. If your performance doesn’t seem right double check to make sure everything has been done properly. 15. EPI is constantly testing our products. Sometimes there is a need to contact the user with new technical information. To ensure that you are receiving this information visit our web site EPIperformance.com to register your clutch kit.

Incoming search terms:

Sherco Engine Engine Removal and Case Splitting Manual

0

Filed Under (Sherco) by admin on 20-04-2011

download
Engine Removal and Case Splitting Preparation 1. Wash the bike and engine thoroughly. 2. Drain transmission oil by removing drain bolt and copper washer with 5mm Allen. 3. Drain coolant by removing 3 bolts of water pump cover and lifting off engine side case.4. Remove: a. rear fender- two bolts plus one long with washer using 4mm Allen b. fuel tank hose from petcock c. fuel tank- one short bolt and washer using 4mm Allen d. chain master link and chain from front sprocket e. kick starter- one large button head bolt and washer f. rear brake- one bolt/washer using 13mm wrench g. rear brake master cylinder- 2 button head bolts h. gear shifter- one bolt i. flywheel cover – 3 bolts j. clutch slave cylinder- two button head bolts using 4mm Allen k. clutch actuating rod by pulling it out of the case l. airbox three 4mm Allen bolts and loosening Phillips head carb hose clamp m. carburetor cap/slide assembly n. carburetor by loosening Phillips head manifold hose clamp o. spark plug cap p. spark plug q. header pipe 2 bolts into cylinder head r. silencer- 3 bolts (one with washer and nut using 10mm wrench) s. cylinder head coolant hose clamp and hose t. rear shock upper bolt u. radiator plastic cover bolt, then lever up the radiator with screwdriver until the radiator “legs” pop out of frame retaining holes 5. Remove flywheel using flywheel puller tool, taking care not to lose the small Woodruff
key by placing it inside of the magnetic flywheel for safe storage. 6. Remove ignition (3 bolts) and slide rubber grommet and ignition wiring assembly out of the case and out of the way, taking special note of the ignition timing marks. 7. Remove front sprocket and 2 retaining circlips. 8. Remove clutch side case and its 10 bolts using 5mm Allen, being careful not to lose to lose the 2 aluminum alignment pins (dowel pins). Insert the dowel pins into their holes within the Right Crankcase

Incoming search terms:

HARLEY DAVIDSON PASSENGER FOOTBOARD INSERT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
INSTALLATION If replacing an insert or inserts on a vehicle currently equipped with Swept Wing Passenger Footboards: Existing Footboard Insert Removal NOTE Carefully remove the currently installed footboard insert to avoid damage to chrome surfaces. 1. See Figure 1. Fold the passenger footboard (1) into the UP position. 2. Loosen, but do not remove the footboard insert setscrew (2). 3. With the footboard folded DOWN, carefully raise an outside corner of the existing insert with a suitable flat-bladed tool, taking care to avoid damaging the chrome footboard pan. 4. Continue around the insert, using a second tool if necessary to pry the existing insert (3) from the footboard pan. 5. If replacing both inserts, repeat for the opposite footboard. Swept Wing Passenger Footboard Installation 1. If installing inserts on a vehicle NOT currently equipped with Swept Wing Passenger Footboards: •Remove currently installed passenger footboards (if so equipped) per the instructions included with the Swept Wing Passenger Footboard Kit. •Remove currently installed passenger footpegs (if so equipped) by removing the socket screw with lockwasher retaining the footpeg support bracket to the rear fork (swingarm) bracket. 2. Follow the instructions in the Swept Wing Passenger Footboard Kit to install the passenger footboards. Footboard Insert Installation 3. ALL applications: Center the two footboard pivot pins. 4. Use soapy water to moisten the rubber dowel pins and pivot pin slots on the bottom of the new footboard insert. 5. Place the insert into position with the rubber dowel pins mating the holes in the footboard pan. Firmly press the insert into the footboard until the dowel pins pop into place. 6. Fold the passenger floorboard UP and tighten the setscrew to secure the insert. 7. Repeat Steps 3 through 6 for the opposite footboard. NOTE Avoid the contact of chrome surfaces with abrasive materials (stones, sand, etc.) as damage will result

HARLEY DAVIDSON AUTOMATIC COMPRESSION RELEASE TOOLS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
INSTALLATION Compressed air can pierce the skin and flying debris from compressed air could cause serious eye injury. Wear safety glasses when working with compressed air. Never use your hand to check for air leaks or to determine air flow rates. (00061a) Wear safety glasses or goggles while drilling. Flying debris could result in serious eye injury. (00565b) 4 3 6 5 6 1 2 7 is05443 1. Drill, 1.250 inch 2. Drill stop collar, 1.250 inch 3. Drill stop gauge 4. Socket head screw, 5/16 inch 5. Socket head screw, 1/4 inch 6. Dowel pin 7. Top plate Figure 1. Top Plate and Drill Bit Stop Collar Installation 1. Remove valves from cylinder heads. NOTE Do not allow the threaded studs to damage the gasket sealing surface of the cylinder head. 2. See Figure 7 and Table 1. Mount a cylinder head to the tooling plate (1). 3. Place a head bolt spacer (7) over each stock head bolt and lubricate threads and thrust faces, dowels and studs. Tighten head bolts in a crisscross pattern to 10 ft-lbs (13.5 Nm) . 4. See Figure 1. Align the top plate (7) bolt and dowel holes with the head hole pattern, Screamin’ Eagle logo towards the spark plug. This plate will only fit one way for the cylinder head it is being installed on. If the plate does not align with the head, turn it over keeping the logo towards the spark plug and install the cylinder head. 5. Lubricate the two dowel pins (6) and insert in the top plate and into the cylinder head. 6. Apply lubricant to the two socket head screws (4 and 5). Insert into their respective holes in the plate to the cylinder head and tighten to 5 ft-lbs (6.8 Nm)

Incoming search terms:

HARLEY DAVIDSON CHROME INNER PRIMARY HOUSING INSTALLATION INSTRUCTION

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
Kit Contents Table 1. Kit Contents Part Number Description (Quantity) Not sold separately Chrome Inner Primary Housing 786A Sealing fastener (5) INSTALLATION NOTES Whenever the sealing fasteners are loosened or removed, they must be replaced. Always replace using Harley-Davidson® Original Equipment sealing fasteners part 786A. Do not use part 786. The primary housing included in this kit installs in the same manner as the stock inner primary housing with the following exception: Use the five sealing fasteners included with this kit. Install and tighten fasteners to the torque specified below. For 2006 Dyna model motorcycles: Remove dowel pins from the chrome inner primary housing before attempting installation. Using a pair of pliers or vice grips, remove the dowel pins by carefully twisting and pulling on the pins. Be careful not to scratch or mar the chrome or sealing surfaces of the chrome inner primary housing. Remove the chain tensioner anchor plate, bolt and screws from the stock inner primary housing after it has been removed, then install it on the chrome inner primary housing. See the appropriate Service Manual for the proper tightening procedure, and torque specifications. 1. See the Drive section of the appropriate Service Manual, and remove the stock inner primary housing. Clean the internal threads in the crankcase and transmission case where the sealing fasteners were removed using a wire brush. Install the chrome inner primary housing as indicated below. Replace the five stock sealing fasteners with the five bolts included in this kit. Put a light coat of primary oil under the head of the sealing fasteners and then tighten to 23-25 ft- lbs (31-34 Nm)

Incoming search terms:

PASSENGER FLOORBOARD RELOCATION ARMS FOR TRIUMPH AMERICA AND SPEEDMASTER

0

Filed Under (Triumph) by admin on 25-12-2010

download
1. If you are installing the relocation arms at the same time as floorboards install the floorboards first per their instructions. When installing the relocation arms with floorboards already installed proceed as follows. 2. Starting on the left side, fold the floorboard up. Remove the socket head bolt and nut which secures the floorboard to the motorcycles stock peg support and remove the floorboard taking notice of which holes the dowel pins are located in. 3. Install one of the 5/16″x1 Ω” hex bolts supplied thru the stock peg support from the backside (The threads of the bolt will face out towards you.) Place the two dowel pins into the holes at one o’clock and seven o’clock on the stock peg mount. Place the spacer blocks backside (stamped with an “L”) onto the bolt and align the hole with the pins. 4. Locate the relocation arm that has an “L” stamped on the backside of it. Place two of the supplied dowel pins into one of the two sets of the holes in the arm that are directly across from one another (180 degrees apart). Place the arm onto the spacer bock aligning the pins in the arm with the holes closest to six and twelve o’clock. Depending on which of the two sets of holes on the arm you chose the arm would, either be down at about seven o’clock or just below nine o’clock. These are the initial height settings and you may select which ever set is most comfortable for the passenger. Install one of the acorn nuts supplied onto the bolt and make finger tight. 5. Place the floorboard with its two dowel pins into the set of holes at the other end of the relocation arm that allows the floorboard to be horizontal or parallel to the ground. Use one of the 5/16″x3/4″ socket head bolts supplied to bolt the floorboard to the relocation arm and make finger tight. 6. Install the right side in the same manner, place the dowel pins in the holes at eleven o’clock and at five o’clock on the stock peg mount, then the spacer blocks backside (stamped “R”) onto the pins followed by the relocation arm with two dowel pins in one set of holes (180 degrees apart). Check to see that the right arm is at the same height or position as the left then install the acorn nut finger tight. Bolt the floorboard the other end of the arm using the remaining dowel pins and socket head bolt. Tighten the two bolts with the acorn nuts and the two socket head bolts securely

TRIUMPH AMERICA AND SPEEDMASTER PASSENGER FLOORBOARDS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 25-12-2010

download
1. Remove the 12mm nuts located behind the stock foot peg assemblies and remove the peg sets. 2. Starting on the left side locate the left floorboard assembly and left round chrome spacer block. These will be stamped with an” L” on the back side. Insert two of the 3/16″ x 1/2″ dowel pins supplied into the two holes where the foot peg was mounted at one o’clock and seven o’clock. Place the spacer blocks backside (stamped with the L) onto the pins 3. Place two more of the dowel pins in the holes on the outside of the block using the holes at twelve o’clock and six o’clock. Place the left floorboard assembly onto the spacer block and pins so that it is parallel to the ground or horizontal (this will be the holes closest to six and twelve o’clock on the backside of the floorboard assembly). Insert one of the 5/16″ x 2″ socket head bolts into the center-mounting hole. Place one of the 5/16″ washers, lock washers and nuts onto the bolt and make finger tight. Recheck to be sure the floorboard is parallel to the ground. 4. On the right side install two more of the dowel pins supplied into holes where the foot peg was mounted at eleven o’clock and five o’clock. Place the remaining spacers backside (stamped with an R) onto the pins 5. Place the remaining two dowel pins supplied into the holes of the spacer block at six o’clock and twelve o’clock. Place the right floorboard assembly onto the spacer block and pins so that it is parallel to the ground or horizontal (this will be the holes closest to six and twelve o’clock on the backside of the floorboard assembly). Insert one of the 5/16″ x 2″ socket head bolts into the center-mounting hole. Place one of the 5/16″ washers, lock washers and nuts onto the bolt and make finger tight. Recheck to be sure the floorboard is parallel to the ground. NOTE; if you are also installing the TA005-5 relocation arms, follow those instructions next. Finally be sure to tighten all bolts securely

YAMAHA ROAD STAR PASSENGER FLOORBOARD RELOCATION ARMS INSTALLATION INSTRUCTONS

0

Filed Under (Yamaha) by admin on 23-12-2010

download
1. If you are installing Relocation Arms and Passenger Floorboards, install the floorboards first per their instructions. When installing the Relocation Arms with Passenger Floorboards already installed proceed as follows. 2. Starting on the LEFT side, fold the floorboard up. Remove the socket head bolt which secures the floorboard to the motorcycles stock peg support and remove the floorboard taking notice of which pinholes the dowel pins are located in. 3. Locate the Relocation Arm that has an “L” stamped on the backside of it. Place two of the supplied dowel pins into one of the two sets of the pinholes in the backside of the arm that are directly across from one another. (180 degrees apart.) Place the arm onto the mounting block and align the pins in the arm with the holes closest to the desired height you wish the floorboard to be at. Bolt the arm to the mounting block loosely using one of the supplied 5/16″ X 1″ button head bolts. 4. Place the Passenger Floorboard with its two dowel pins into the set of pinholes at the other end of the relocation arm that allows the floorboard to be parallel (horizontal) to the ground. Use one of the supplied 5/16″ X 3/4″ socket head bolts to mount the floorboard to the relocation arm and make finger tight. 5. Install the RIGHT side in the same manner. Check to see that the right arm is at the same height and/or position as the left. Bolt the floorboard to the other end of the arm using the remaining dowel pins and socket head bolt. Tighten all four bolts on both sides securely. NOTE: Four other height positions are possible by using the other sets of holes on the front side of the mounting block and backside of the relocation arm

Incoming search terms: