HARLEY DAVIDSON TLE/TLE-ULTRA SIDECAR ATTACHMENT KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
REMOVAL NOTES Refer to the service manual for more information on these generalized steps. Save all removed parts (unless otherwise noted) for installation of this kit or for motorcycle operation without the sidecar. 1. For TLE-Ultra Models: Remove both lower fairings. 2. Remove the bolt and lockwasher securing the right passenger footrest bracket and remove the bracket with footrest. 3. Remove the three right side exhaust heat shields. Some models may require removal of the right side exhaust pipes. 4. Remove stock clutch cable. 5. Remove rear master cylinder/rear brake pedal assembly. Remove rear brake pedal from master cylinder assembly. Remove and save rubber pedal pad and brake pedal. Discard cotter pin. 6. Cut the cable straps holding front oxygen sensor connector to frame bracket. 7. Remove wire harness/brake line clip from right lower frame tube. INSTALLATION New Clutch Cable Installation 1. Refer to the service manual and follow instructions to remove stock clutch cable. 2. Refer to the service manual and follow instructions to connect the new clutch cable to clutch hand lever. 3. For FLHT/C/CU: Follow the instructions in the service manual to route new clutch cable through fairing. 4. For FLHR/C Models: Capture the cable in a clamp at the left upper passing lamp bolt. On FLTR models, capture the cable in a clamp at the left upper bolt securing the speedometer and tachometer housing to the upper fork bracket. These locations are identical with stock cable routing. 5. See Figure 1. Route clutch cable down along left frame downtube (1). 6. Continue to route cable down between left front engine isolator and crankcase. Clutch cable will cross to the right side of motorcycle beneath the crankcase, to the clutch release cover on the right side of the transmission. 7. Install clutch cable fitting into clutch release cover. Refer to the service manual. NOTES The final positioning and attachment of the clutch cable and clutch cable adjustment will be performed after sidecar mounts have been installed. Verify that the clutch cable and the rear brake line do not make contact. Damage could result. 1 2 3 is05785 1. Downtube 2. Clutch cable 3. Route clutch cable behind left front engine iso- lator Figure 1. Route Clutch Cable Relocating Oil Pressure Sending Unit NOTES Perform this procedure on all models equipped with an oil pressure gauge or Police models. All other models proceed to “Master Cylinder Assembly/Rear Brake Pedal Modification.” 1. Remove cable strap securing oil pressure wire harness to frame. 2. Locate the latch on connector to oil pressure sender (next to lower right frame downtube). Raise latch on connector and disconnect connector from oil pressure sender. 3. Remove the oil pressure sender using a 1-1/16 inch open- end crowfoot wrench. 4. See Figure 16. Coat threads of elbow (44) with Loctite 565 and install into crankcase oil pressure sender threads. 5. See Figure 2. Install elbow (1) until snug so open end is in the five-o’clock position (2). Do not over-tighten or crankcase may be damaged. 6. Coat threads of oil pressure sender with Loctite 565 and install into 90 degree brass elbow. Use a 1-1/16 inch open- end crowfoot and tighten to 96-120 in-lbs (11-14 Nm) . 7. Install connector on oil pressure sender unit. Verify that slight clearance to the right engine isolators is present. Adjust position of elbow as required to provide clearance

HARLEY DAVIDSON FXST, FXSTS, FXSTD ENGINE GUARD KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
INSTALLATION FXSTD models only: •See Figure 4. Remove the clutch cable from the plastic clamp (1) on the downtube. Remove and discard the clamp. •Position the engine guard between the front of the down- tubes and behind the clutch cable. All Models 1. See Figure 1 and Figure 2. Align the top-center mounting plate with the frame crossbrace, located between the front downtubes. is02709 Figure 1. Installed Engine Guard 2. Fasten the mounting plate to the crossbrace with a pan- head screw (3), 5/16 inch washer (2), and 5/16 inch hex nut (1) as shown. Do not tighten. 3. See Figure 5. Fasten the left-side engine guard (1) at the indicated location with a buttonhead screw (7), 3/8 inch washer (6), and 3/8-16 nylon locknut (5). Do not tighten

HARLEY DAVIDSON DETACHABLE WINDSHIELD AND DOCKING HARDWARE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
These kits fit 1984 and later FXST, FXSTB, FXSTC, and 1993 and later FXDWG model motorcycles when equipped with passing lamps. INSTALLATION 1. To protect against scratches, cover gas tank and front fender before installation. is 01985 Figure 1. New Clutch Cable Routing 2. For FXSTB Models: Proceed to Step 3. For all except FXSTB: See Figure 1. Relocate the clutch cable to the inside of the handlebars as follows: a. Locate cable adjuster halfway along clutch cable by the front frame downtube and slide off rubber boot. b. Holding cable adjuster with 1/2 inch wrench, loosen jam nut using a 9/16 inch wrench. Back jam nut away from cable adjuster. Move adjuster toward jam nut to introduce a large amount of free play at hand lever. c. Remove small snap ring from pivot pin groove at bottom of clutch lever bracket. Remove pivot pin and clutch hand lever from bracket. Remove anchor pin and clutch cable eyelet from clutch hand lever. d. See Figure 1. Route clutch cable to the inside of the handlebars and reconnect clutch cable to clutch lever. e. See Figure 2. Turn cable adjuster away from jam nut until slack is eliminated at hand lever. Pull clutch cable ferrule away from clutch lever bracket to check free play. Turn cable adjuster to obtain 1/16-1/8 inch (1.6- 3.2 mm) free play between end of cable ferrule and clutch lever bracket. f. Hold adjuster with 1/2 inch wrench. Using 9/16 inch wrench, tighten jam nut against cable adjuster. Cover cable adjuster mechanism with rubber boot

HARLEY DAVIDSON CHROME OIL FILTER MOUNT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 04-02-2011

download
INSTALLATION 1. See Figure 2. Remove oil filter (B). 2. Remove existing oil filter mount screws and washers and remove existing oil filter mount. Discard original screws and washers. 3. Remove original oil filter adapter (A) from old mount. Clean all oil from adapter, then apply Loctite 243 (blue) to the threads on the side of the adapter that mates with the new mount. Install adapter into new mount (1). 4. Place new O-rings (2) from kit into bottom of new chrome oil filter mount (1), place oil filter mount in position, and install new oil filter mount screws (4), lockplate (5), and washers (3) from kit. Lockplate must be positioned as shown in Figure 2. NOTE Carefully follow the instructions for installing the lockplate. Failure to correctly install the lockplate could cause the fasteners to turn and allow the filter mount to loosen. A loose filter mount could allow hot oil to spray onto riders or the motorcycle which could lead to personal injury and/or death. 5. Use Loctite 243 (blue) on threads. Insert upper and lower hex bolts through lock plate. Position flat washer behind lockplate and thread hex bolts into case. Snug bolts but do not tighten. 2 4 1 3 is03977 1. Top bolt 2. Center bolt 3. Lower bolt 4. Center bolt, re-torque Figure 1. Torque Sequence NOTE On FL models, it may be necessary to clip clutch cable strap on frame downtube and move cable to the side. This will allow easier access when tightening new oil mount hex head bolts. 6. See Figure 1. Tighten hex head bolts to 130-140 in-lbs (14.6-15.8 Nm). Tighten hex head bolts starting with top (1), middle (2), bottom (3), then re-tighten middle bolt (4). 7. See Figure 2. Carefully bend over lockplate (5) edges at top and bottom fastener to prevent hex head bolt from turning. 8. Install oil filter (B)

Incoming search terms: