1990 Harley Davidson ULTIMA 6 SPEED BUILDERS KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-04-2012

download
For 2000 & later models removal of approximately 1/4 of an inch off of the shifter arm bushing is likely required. Doing so will allow installation of the retaining clip & washer onto the shifter arm. It is good practice to double check how much material should be removed before cutting the bushing. See fig. 1 & 2 Install supplied Main drive gear bearings & countershaft needle bearings using special tool # 97-164 NOTE: Lightly coat bearings with assembly lube or gear oil for easier installation. Install supplied Main drive gear retaining clip & verify that it is fully seated and cannot come out. Do not re-use old bearings or retaining clip. Install supplied Main drive gear into bearings using special tool # 97-166 See fig. 3 Install supplied trap door gasket & verify that it is on correctly. Install supplied 6 speed gear set making sure to align the countershaft with the needle bearing assembly. Slowly slide in gear set until the mainshaft & countershaft will not slide in any further. Lightly tapping on the trap door (while verifying that there is no interference) with a soft blow hammer will then fully seat the shafts & trap door. See fig. 4 Once gear set is installed use the supplied 5/16-18×1-1/2 & 1/4-20×1-1/2 bolts to secure the trap door. Torque the 5/16 bolts to 15 ft-lbs w/ red loctite (high strength) Torque the 1/4 bolts to 9 ft-lbs w/ red loctite (high strength) See fig. 5 FIG. 1 FIG. 2 FIG. 3 FIG. 4 FIG. 5 2 FIG. 6 At this time check to make sure all gears rotate freely & that all slider gears slide with no interference. Lightly lube & install supplied quad seal onto main drive gear. See fig. 6 Install Main seal using special tool # 97-164. See fig. 7 Install original spacer onto mainshaft. NOTE: Beveled side goes in towards quad seal. See fig. 8 Install supplied transmission drain plug & supplied speedo sensor plug with gasket. Install supplied shifter forks onto appropriate slider gears. See fig. 9 Lightly lube & install supplied shift fork shafts. NOTE: Short shaft is installed from the right side with the threaded hole facing out. Long shaft is installed from the left side & should not protrude from the right side of case. See fig. 10 Install supplied shift fork shaft allen head plugs. (Use red loctite to prevent movement of plug & to aid in sealing)

Incoming search terms:

SUZUKI SV1000 PERIODIC MAINTENANCE

0

Filed Under (Suzuki) by admin on 26-02-2011

download
MAINTENANCE AND TUNE-UP PRO- CEDURES This section describes the servicing procedures for each item of the Periodic Maintenance requirements. AIR CLEANER I Inspect every 6 000 km (4 000 miles, 6 months) and replace every 18 000 km (11 000 miles, 18 months) . • * Remove the seat. (LF6-7) • * Lift and support the feul tank . (C-74-65) • * Remove the air cleaner box cap O. • * Remove the air cleaner element O. • * Carefully use air hose to blow the dust from the cleaner ele- ment. CAUTION Always use air pressure on the throttle body side of the air cleaner element . If air pressure is used on the other side, dirt will be forced into the pores of the air cleaner element thus restricting air flow through the air cleaner element . PERIODIC MAINTENANCE 2-5 2-6PERIODIC MAINTENANCE • * Reinstall the cleaned or new air cleaner element in the reverse order of removal . CAUTION If driving under dusty condition, clean the air cleaner element more frequently. The surest way to accelerate engine wear is to use the engine without the element or to use a ruptured element. Make sure that the air cleaner is in good condition at all times. Life of the engine depends largely on this component! NOTE: When cleaning the air cleaner element, drain water from the air cleaner by removing the drain plug . SPARK PLUG Inspect every 6 000 km (4 000 miles, 6 months) and replace every 12 000 km (7 500 miles, 12 months) . No. 1 (FRONT) SPARK PLUG REMOVAL • * Remove the radiator mounting bolt O. • * Move the radiator forward. • * Remove the spark plug cap O. NOTE: Be careful not to damage the radiator fins . A WARNING The hot radiator and the hot engine can burn you . Wait until the radiator and the engine are cool enough to touch . • * Remove the spark plug with a spark plug wrench. 1 6 I It No. 2 (REAR) SPARK PLUG REMOVAL • * Remove the seat. (r–,-6-7) • * Lift and support the fuel tank . (=4-65) 4-65) • * Disconnect the camshaft position sensor 1O and breather hose (Z. • * Remove the rubber heat shield ® . • * Remove the spark plug cap . • * Remove the spark plug with a spark plug wrench . HEAT RANGE • * Check to see the heat range of the plug . CARBON DEPOSIT •Check to see if there are carbon deposits on the plugs . If carbon is deposited, remove it with a spark plug cleaner machine or carefully using a tool with a pointed end . SPARK PLUG GAP • * Measure the plug gap with a thickness gauge . If out of specification, adjust it to the following gap . 09900-20803 : Thickness gauge Spark plug gap OA Standard: 0.6 – 0 .7 mm (0.024 -0.028 in) ELECTRODES CONDITION •Check to see the worn or burnt condition of the electrodes . If it is extremely worn or burnt, replace the plug . And also replace the plug if it has a broken insulator, damaged thread . CAUTION Confirm the thread size and reach when replacing the plug. If the reach is too short, carbon will be deposited on the screw portion of the plug hole and engine damage may result

Incoming search terms:

APRILIA QUASAR 50-100-125-180 maintenance Manual

0

Filed Under (Aprilia) by admin on 26-11-2010

download
CHANGING ENGINE OIL CAUTION In case of oil leakage or malfunctions, contact an Aprilia Authorised Dealer . Do not dispose of oil in the environ- ment. Dispose of engine oil – stored in a sealed container – through the nearest waste oil reclamation firm or through the supplier. Carefully read page 34 (MAINTE- NANCE) To change engien oil: ◆ Ride for a few kilometres until engine reaches the operating temperature, then stop the engine. ◆ Position a graduated container (1), under the drain plug (2). ◆ Loosen oil filler plug (4) and drain plug (2). ◆ Let oil flow out of the sump. ◆ Loosen oil filter (3) and carefully clean it. ◆ Refit the filter and tighten fully. ◆ Tighten drain plug (2) and pour recommended oil into filler plug (4), see page 58 (LUBRICANT CHART). ◆ Tighten the filler plug. CAUTION Carefully tighten filler and drain plugs and ensure oil does not leak out. Periodically check for leaks at the casing cover gasket. Do not use the vehicle with insufficient lubrication or with contaminated or unsuitable lubricants, since this would cause early wear of the moving parts and may also cause irreparable failures Fluid reservoir (1) is under rear right wheelhouse. CAUTION Position the vehicle on firm and flat ground. ◆ Make sure that the fluid contained in the reservoir exceeds the ” MIN ” mark stamped on the reservoir. MIN = minimum level. WARNING Do not use the vehicle if the braking system is leaking fluid. CAUTION Do not use the vehicle if the fluid is below the “MIN” mark. 1
27 use and maintenance Quasar 50 – 100 – 125 – 180 CAUTION Brake fluid level decreases as the brake pads wear down. Should the level be too low: ◆ Check the brake discs and pads for wear, see page 27 (CHECKING THE BRAKE PADS FOR WEAR) If the pads and/or the disc do not need re- placing: ◆ Contact an Aprilia Authorised Dealer that will top up the fluid. WARNING Check the brake for proper operation. When the brake lever has exceeding travel or if you notice a loss of braking, contact an Aprilia Authorised Dealer . The braking system may need bleed- ing. CHECKING THE BRAKE PADS FOR WEAR Carefully read page 26 (BRAKE FLUID – recommendations) , page 26 (DISC BRAKES) and page 34 (MAINTE- NANCE). Periodically check brake pad wear. The rate at which brake pads will wear depends on vehicle usage, riding style and road surface condition. Outlined below is a quick brake pad inspection procedure: ◆ Visually check between brake disc and pads, check both pads (1) looking from the bottom at the rear end. ◆ Should friction material (of even one pad only) be worn down to 1.5 mm of thickness, have both pads replaced

Incoming search terms:

2008 FLT Police Models Service Manual Supplement

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
ITEM SERVICED 14-21 ft-lbs (19.0-28.5 Nm) Drain plug torque Engine oil and filter 4 qt. (3.8 L) Oil capacity Hand tighten 1/2-3/4 turn after gasket contact Filter 63798-99A Chrome filter part number 63731-99A Black filter part number FORMULA+ TRANSMISSION AND PRIMARY CHAIN LUBRICATION (Part No. 99851-05) Lubricant type and capacity Primary chain lubricant Wet: 38 oz. (1124 ml) Dry: 45 oz. (1331 ml) 14-21 ft-lbs (19.0-28.5 Nm) Primary chaincase drain plug torque 1/2-1 turn Adjuster screw free play Clutch adjustment 72-120 in-lbs (8.1-13.6 Nm) Adjuster screw locknut torque 1/16-1/8 in. (1.6-3.2 mm) Free play at hand lever 84-108 in-lbs (9.5-12.2 Nm) Clutch inspection cover torque Dipstick at FULL with motorcycle on jiffy stand and filler plug resting on threads. Lubricant level Transmission lubricant FORMULA+ TRANSMISSION AND PRIMARY CHAIN LUBRICATION (Part No. 99851-05) Lubricant type and capacity 32 oz (0.95 liters) 14-21 ft-lbs (19.0-28.5 Nm) Transmission drain plug torque 25-75 in-lbs (2.8-8.5 Nm) Transmission filler plug/dipstick torque Front: 36 psi (248 kPA) Pressure: solo rider Tire pressure and wear Rear: 36-40 psi (248-276 kPA) Replace if less than 1/32 in. (0.8 mm) of tread pattern Wear 55 in-lbs (6.2 Nm) minimum Spoke nipple torque Wheel spokes 99953-99A (12 oz.) D.O.T. 4 hydraulic brake fluid part number Brake fluid level Front: 0.20 in. (5.0 mm) Fluid level (from top of master cylinder reservoir) Rear: 0.26 in. (6.5 mm) Front: 7-10 in-lbs (0.8-1.1 Nm) Master cylinder reservoir cover screw torque Rear: 12-15 in-lbs (1.4-1.7 Nm) 0.016 in. (0.4 mm) Minimum brake pad thickness Brake pads and discs 75-102 in-lbs (8.5.-11.5 Nm) Brake caliper pad pin torque Front: 0.18 in. (4.5 mm) Minimum brake disc thickness Rear: 0.25 in. (6.3 mm) 0.008 in. (0.2 mm) Maximum brake disc lateral runout (warpage) 10 lb. (4.5 kg) Upward force applied at midpoint of bottom belt strand Drive belt deflection 3/8-7/16 in. (9.5-11.1 mm) FLHTP 1/4-5/16 in. (6.4-7.9 mm) FLHP/FLHPE 40-60 in-lbs (4.5-6.8 Nm) Air cleaner cover bracket screw torque Air cleaner 36-60 in-lbs (4.1-6.8 Nm) Air cleaner cover screw torque LOCTITE MEDIUM STRENGTH THREADLOCKER 243 (BLUE) Air cleaner cover screw Threadlocker Part No. 99642-97 (6 ml) LUBIT-8 SUPER OIL, Part No. 94968-85TV (1/4 fl. oz.) Lubricant part number Clutch cable 35-45 in-lbs (4.0-5.1 Nm) Handlebar switch housing screw torque

Incoming search terms:

All Victory Models OIL CHANGE KIT

0

Filed Under (Victory) by admin on 13-11-2010

download
1. Warmup the engine for several minutes. 2. Stop the engine. Securely support the machine on its sidestand. IMPORTANT: Take the proper precautions sot hem achinedoes not tip while working on it. Place an oil pan under the engine and loosen the oil fill cap/ dipstick. 3. Remove the drain plug (1) and drain the oil. 4. Remove the oil filter (2). 5. Reinstall the drain plug with anew sealing washer or O-rIngfromthekit. Torque drain plug to the specification listed in the Owner’sManualorService Manual. 6. Apply alight coat of engine oil to theO-ring of the new oil filter. Make sure the O-ring is seated properly in the groove on the filter. 7. Install filter and tighten it 3/4 of a turn after O-ring contacts engine case. 8. Remove the fill cap/dipstick and fill the engine with the amount of oil recommended in the Owner’sManualor Service Manual and reinstall the dipstick /filler cap. 9. Start the engine and warm it up for several minutes and check for leaks. If any leaks are found, stop the engine and determine the source of the problem before starting the engine again. Contact your Victory dealer if you cannot determine the source of the leak. NOTE: After the engine is started, the oil indicator light should go off. If the indicator light flickers or remains on, immediately stop the engine and take your motorcycle to a Victory dealer. 10. Stop the engine and inspect oil level (refer to the Owner’sManualorService Manual). 11. Install the fill cap/dipstick and tighten securely

Incoming search terms: