Harley Davidson DRESSERS TUNED-FLOW SLIP-ON MUFFLERS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 23-03-2012

download
Installing the Tips: 1. Use a long 3/16″ ball drive Allen wrench to remove the two hidden retaining screws. 2. Rotate the tip to the desired position and relocate the retaining screws and lock washers inside the tip. 3. Apply a small amount of anti-seize compound to the threads and tighten to 8 ft./lbs. 4. Check the tip bolts after a brief test ride. Adjusting the Hooker Tuned-Flow┬« Muffler: 1. Loosen the socket head bolts located in the aluminum ring at the end of the muffler approximately 5 turns using a 3/16″ Allen wrench. Alternate back and forth between each bolt 1/2 turn at a time to keep from binding. 2. Using your fingers, pull the center barrel of the muffler approximately 1/8″ towards the back of the motorcycle and rotate to the desired setting. If warm, use a rag or gloves. 3. By rotating the exhaust barrel and aligning the notch in the barrel with the index marks in the aluminum ring, the power band can be adjusted. The “H” setting will bias the power towards High RPM Horsepower, while the “T” setting will provide more Low RPM Torque. The muffler is infinitely adjustable between these two settings

HARLEY-DAVIDSON DRESSER BIG SHOT DUALS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-03-2012

download
1. Remove both left and right saddlebags and set them aside. 2. Loosen the bolt from the pinch clamp on the front end of each muffl er. Note: On older model Dressers, spread the clamps just enough to remove them. 3. Remove the two 5/16″ bolts that mount the muffl er to the saddlebag supports. Repeat this step on the opposite muffl er. 4. Remove the stock muffl ers with sliding hangers and set them aside. Note: It may be necessary to use a penetrating lubricant to loosen the muffl er from the head pipe. 5. Remove the right hand fl oor board. 6. Remove both passenger fl oor boards. 7. Loosen the heat shield clamps on both front and rear exhaust pipes. 8. Loosen the rear head pipe clamp located behind the rear cylinder. Remove the section of head pipe connecting the left side muffl er. 9. Remove the clamp holding the front head pipe to the transmission housing. 10. Remove the two mounting nuts from each head pipe, located at the cylinder head. Carefully remove the head pipes and set them aside. 11. Remove the rear cylinder bracket by removing the two starter mounting bolts. Install new mounting bracket (stamped 353-P), and torque to (13-16) ft. lbs. (Figure 1). Make sure the battery ground cable is secure and properly routed. Install mounting post (from stock system) so the nut is accessible from right side of motorcycle and saddle will support underside of exhaust pipe. Note: Pre 1998 dressers do not come with this mounting post. It can be ordered from your local dealer, Harley part number: 65619-98. 12. Carefully remove the exhaust port fl anges and circlips from the stock exhaust system using snapring pliers. Note: If circlips look bent or twisted replace them

Harley Davidson Touring Bikes TRUMPET INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2012

download
COMPRESSOR INSTALLATION TOUR MODELS 1992 -2000 On the Dressers and Tour bikes, remove the seat. If the battery is located underneath the seat, then remove the right saddlebag and right hand side cover. Using a zip tie, mount the compressor to the main wiring harness at the front of the covered area with the compressor air outlet facing down. If the battery is not under the seat and is located beside the right saddlebag, the compressor will be mounted underneath the seat, utilizing a bolt to the frame The air hose routes from the air horns, behind the fuel valve, over the rear cylinder and to the right side cover or underneath the seat. Do not cut hose until you connect it to the compressor. TOUR MODELS 2001 & NEWER On the Dressers and Tour bikes, the compressor will mount under the seat, in the square hole in front of the frame, just in front of the battery. The air output will face left toward the air horns. The hose routes thru a hole at the bottom of the square hole, then to the air horns. WIRING Connect both black wires from the relay to the original horn wires. It does not matter which wire you connect. The fuse wire on the relay will connect to the positive terminal on the battery. Observe negative and positive terminals on compressor. Ground the negative terminal to the battery. The positive terminal connects to red wire on relay. Refer to wiring schematic on the next page