HONDA 420 RANCHER 2×4/4×4 2007-2009 CLUTCH KIT INSTRUCTIONS

0

Filed Under (Honda) by admin on 22-12-2011

download
Remove key from the ignition switch. Remove the side panels from both sides. Remove both foot wells. 2. Drain coolant. Remove the oil drain plug from the motor; if you carefully drain it into a clean container you should be able to reuse it. 3. Disconnect shift motor (on electric shift models only). Remove coolant hoses. 4. Remove the bolts that mount the front differential to the frame, no other parts need to be removed. Carefully slide the front differential towards the front of the machine; you might need to lift up slightly to get the differential to move. Remove the drive shaft. Remove o-ring on output shaft (on motor). 5. Remove the fuel pump. 6. Loosen the front crankcase cover bolts, keep track of each bolt length and location. Slowly remove the crankcase cover. Carefully watch for o-ring shims and dowel pins that may fall out. 7. Unstake the nut holding the clutch on and remove nut. Using Honda tool #07933-HB3000A thread the large part of the tool into the center of the clutch. Tighten the center bolt on the tool while holding the large part of the tool with a wrench. This will pull the clutch off the machine. Place the clutch on a clean work surface. EPI performance.com
8. Using the c-clamps push down slightly on the outside cover and remove the four e-clips. Keeping track of which way they come off, remove the round metal plates one at a time. This will allow you to see the complete spring. Remove one end of each spring using a spring tool or needle nose pliers and then remove springs. Install the EPI springs by inserting the spring into the outer edge first. Using a spring tool or pliers (45 degree bent pliers work well) pull on the spring and insert the end into the hole. Install the metal plates and the e-clips. If you can’t get the plates to sit flat make sure each clutch arm is flat against the bottom plate of the clutch. Occasionally when you put the springs on, the clutch arms will pop up. Slide the clutch into the machine. The Sprague clutch is marked “outside” when installing make sure this is facing out. Torque clutch nut to 87 ft/lbs. 9. Clean the gasket surface on the motor and on the cover. Put a thin layer of Honda Bond or Yamabond semi-drying liquid gasket (or something similar as long as it is semi-drying) on the crankcase cover. Carefully install crankcase cover, do not force cover on. Torque bolts to 9 ft/lbs. 10. Install the fuel pump. 11. Install the o-ring on the output shaft (on motor) and install the drive shaft. Carefully slide the front differential back into place and mount to the frame. Install the coolant hoses. Refill your engine coolant to the proper level according to your owner’s manual. 12. Install the oil drain plug. Refill your engine to the proper level according to your owner’s manual. You can reuse your oil if it is clean and was drained into a clean container. Only use manufactures recommended oil. 13. Be sure to double check coolant and oil levels and to look for any leaks after the machine has run for a few minutes. 14. Go out and ride your machine. If your performance doesn’t seem right double check to make sure everything has been done properly. 15. EPI is constantly testing our products. Sometimes there is a need to contact the user with new technical information. To ensure that you are receiving this information visit our web site EPIperformance.com to register your clutch kit.

Incoming search terms:

2010 HONDA VFR1200F Dual Clutch Transmission Specifications

0

Filed Under (Honda) by admin on 18-02-2011

download
Specifications VFR1200F Dual Clutch Transmission (ED-type/ F-type) ENGINE Type Liquid-cooled 4-stroke UNICAM 76° V-4 Displacement 1237cc Bore  Stroke 81  60mm Compression Ratio 12:1 Max. Power Output ED: 127kW/10,000min-1 (95/1/EC) F: 83kW/9,500min-1 (95/1/EC) Max. Torque ED: 129Nm/8,750min-1 (95/1/EC) F: 115Nm/4,000min-1 (95/1/EC) Idling Speed 1,150 min-1 Oil Capacity 4.9 litres FUEL SYSTEM Carburation PGM-FI electronic fuel injection Aircleaner Oil-permeated, viscous-type paper filter Fuel Tank Capacity 18.5 litres Fuel Consumption ED/E : 15.9 km/l F : 15.9 km/l (tested in D-Mode) (WMTC mode*) VFR1200F 03/05/10 9 9 ELECTRICAL SYSTEM Ignition System Computer-controlled digital transistorised with electronic advance Ignition Timing 8.4° BTDC (idle speed) Sparkplug Type IMR9E-9HES (NGK); VUH27ES (DENSO) Starter Electric Battery Capacity 12V/11.2Ah (YTZ14S) ACG Output 570W Headlights H7x2 (55Wx2) Tail-light 5Wx2,STOP LIGHT 21W( 21/5W+5Wdual-light) DRIVETRAIN Clutch Wet multi-plate, hydraulic, dual Clutch Operation Hydraulic Transmission Type Constant mesh 6-speed Primary Reduction 1.738 (73/42) Gear Ratios 1 2.4666 (37/15) 2 1.7894 (34/19) 3 1.4090 (31/22) 4 1.1600 (29/25) 5 1.0322 (32/31) 6 0.9393 (31/33) VFR1200F 03/05/10 10 10 Final Reduction 2.7061 Final Drive Shaft FRAME Type Diamond; aluminium twin-spar CHASSIS Dimensions (LWH) 2250  740 1220mm Wheelbase 1,545mm Caster Angle 25.5° Trail 101mm Turning Radius 3.5m Seat Height 815mm Ground Clearance 125mm Kerb Weight 277kg Loaded Weight 473Kg SUSPENSION Type Front 43mm cartridge-type telescopic fork with stepless preload adjustment, 120mm axle travel RearPro-Link with gas-charged damper, VFR1200F 03/05/10 11 11 25-step (*stepless remote-controlled hydraulic) preload and stepless rebound damping adjustment, 130mm axle travel WHEELS Type Front 5-spoke hollow gravity Die-cast aluminium Rear7-spoke gravity Die-cast aluminium Rim Size Front 17M/C  MT3.50 Rear 17M/C  MT6.00 Tyre Size Front 120/70 ZR17M/C (58W) Rear 190/55 ZR17M/C (75W) Tyre Pressure Front 250kPa Rear 290kPa BRAKES Type Front 320mm dual floating hydraulic disc with two 6-piston callipers, C-ABS and sintered metal pads Rear276mm hydraulic disc with 2-piston calliper, C-ABS and sintered metal pads All specifications are provisional and subject to change without notice. * Please note that the figures provided are results obtained by Honda under standardized testing conditions prescribed by WMTC. Tests are conducted on a rolling road using a standard version of the vehicle with only one rider and no additional optional equipment. Actual fuel consumption may vary depending on how you ride, how you maintain your vehicle, weather, road conditions, tire pressure, installation of accessories, cargo, rider and passenger weight, and other factors

2010 HONDA VT1300CX Specifications/ Press Information

0

Filed Under (Honda) by admin on 18-02-2011

download
Specifications General Model VT1300CX Mold Type ED-type Engine Type Liquid-cooled SOHC 52° V-twin Displacement 1,312cm³ Bore x Stroke 89.5 x 104.3mm Compression Ratio 9.2 : 1 Max. Power Output 42.5kW / 4,250min-1 (95/1/EC) Max. Torque 107Nm / 2,250min-1 (95/1/EC) Idling Speed 900min-1 Oil Capacity 4.3 litres Fuel System Carburation PGM-FI with automatic enricher circuit Throttle Bore 38mm Aircleaner Viscous, cartridge-type mesh net filter Fuel Tank Capacity 12.8 litres Electrical System Ignition System Digital with 3-dimensional mapping, 2 sparks per cylinder Ignition Timing 8° BTDC (idle) ~ 57.7° BTDC (5,250min-1) Sparkplug Type DCPR6E (NGK); XU20EPR-U (DENSO) Starter Electric Battery Capacity 12V / 11.2AH ACG Output 381W Headlights 12V, 55W x 1 (low) / 60W x 1 (high) Drivetrain Clutch Wet, multiplate with coil spring Transmission 5-speed Primary Reduction 1.758 Gear Ratios 1 1.900 2 1.231 3 0.912 4 0.757 5 0.676 Final Reduction 2.661 Final Drive Shaft Frame Type Double-cradle; steel Chassis Dimensions (LxWxH) 2,575 x 900 x 1,150mm Wheelbase 1,805mm Caster Angle 32° Trail 90mm Turning Radius 4.1m Seat Height 678mm Ground Clearance 126mm Kerb Weight 303kg (F: 128kg; R: 175kg), *309kg (F: 131kg; R: 178kg) Max. Carrying Capacity 160kg Loaded Weight 463kg , *469kg Suspension Type Front 45mm telescopic fork with 130mm stroke and 102.4mm axle travel Rear Monoshock with adjustable rebound damping and 35-position spring preload adjustability, 95mm axle travel Wheels Type Front9-spoke cast aluminium Rear7-spoke cast aluminium Rim Size Front21M/C x MT2.15 Rear18M/C x MT6.25 Tyre Size Front90/90 R21M/C () Rear200/50 R18M/C () Tyre Pressure Front 225kPa Rear280kPa (with passenger: 280kPa) Brakes Type Front 336mm single disc with twin-piston caliper (*Combined 3-piston calliper and ABS) Rear 296mm disc with single-piston caliper (*Combined twin piston and ABS) * C-ABS version

Honda VTX 1800 Motorcycles ALL Models (Excluding C Model) Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 17-02-2011

download
Specifications Overall width 55.5 in. Overall length 108.06 in. Overall length w/ EZ-Steer 111.75 in. Wheelbase 72.44 in. Wheelbase w/ EZ-Steer 76.125 in. Load capacity 640 lbs. Brakes High-performance rear disc Tires 205/70R-15 Turning Radius 12.3 ft. Wheels Offset +35 mm 15x7JJ 4×4.5 Tire Pressure 20-25 psi · Suspension: “Zero-Flex” swing arm and two new (replacement) Progressive coil-over shocks. · Rear Differential: Champion Left Hand Drive Light Weight Rear Differential Assembly. · Brakes: Original front plus 2 high performance disc brakes at rear. · Storage Capacity: 6.75 cubic feet – 3 full-face helmets and additional over wheel storage. 2 Removal of Original Parts Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. · Rider’s Seat (to be re-installed without modification) . · Passenger Seat and mounts (to be reinstalled without modification) . NOTE: OEM front and rear seat mounting bolts to be retained and reused. · Left and right passenger foot rests and mounts (to be reinstalled with modification) . · Mufflers (to be re-installed and relocated with minor modification) . · Rear Fender (complete w/ sub frame and all attaching parts) . · Swing Arm, Drive Shaft and Rear Wheel (complete w/ brake line and all attaching parts) . Core Return There are NO core return parts for this model. Installation of Champion Trike Conversion Kit 3.1 Modify Frame and Passenger Footrests. a. Use 17/64″ drill and drill through frame from inside out using passenger footrest mount holes as guide. b. Enlarge the passenger footrest mounting holes on the left and right side of the frame to 27/64″. c. Enlarge the holes in the left and right passenger footrest mounting plates to 27/64″. d. Clean area of all debris. 3.2 Relocate Regulator a. Install supplied “Z” bracket to the regulator as shown using the supplied hardware. b. Attach regulator to frame using the supplied hardware. c. Tie hoses down to avoid contact with the swing arm. Qty Description 1 ¼-20×2 hex head bolt 1 ¼-20×1-1/4 hex head bolt 6 ¼-20 Nyloc nut 10 1/4- SAE flat washer 4 as spacers 3.3 Hose Stay a. For models that have a recover tank below the swing-arm, a holder has been included keep the hose connected to the water pump away from the champion swing-arm. b. Remove the hose from the top of the recovery tank. c. Push the water pump hose forward against transmission. d. Secure hose with supplied stay as shown using existing bolt. Ensure that hose is not being crushed. Bend stay if necessary. e. Reconnect hose to recovery tank

Honda VTX 1300 Motorcycles All Models Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 17-02-2011

download
Removal of Original Parts Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. · Rider’s Seat (to be re-installed without modification) · Passenger Seat (to be reinstalled without modification) NOTE: OEM front and rear seat mounting bolts and brackets to be retained and reused. · Left and right passenger foot rests. (to be re-installed later). · Mufflers (to be re-installed and relocated with minor modification) · Rear Fender (complete w/ sub frame and all attaching parts) · Swing Arm, Drive Shaft and Rear Wheel (complete w/ all attaching parts) · Rear brake Line to hard line in front of the Swing Arm. Core Return There are NO core return parts for this model Installation of Champion Trike Conversion Kit 3.1 Modify Frame and Passenger Footrests. a. Cut and remove passenger foot rest mount from OEM frame on both sides (left hand side picture shown) . Figure 1 b. Clean cut frame and paint black. c. Remove and secure Charcoal Canister. d. Cut and remove charcoal canister frame bracket. Figure 2 e. Clean cut frame and paint black f. Install supplied Canister/Regulator bracket with supplied hardware. Figure 3. Make sure the hoses/electrical wires are routed underneath the bracket as shown. Figure 4 Qty Description 2 3/8-24×1-3/4 hex head bolt 4 3/8 SAE flat washers 2 3/8-24 Nyloc nuts g. Install Canister and Regulator with supplied hardware. Figure 4 Qty Description 4 ¼-20×1-1/4 hex head bolt 8 ¼ SAE flat washers 4 1/4-20 Nyloc nuts

Honda GL1500 Gold Wing Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 17-02-2011

download
REMOVAL OF ORIGINAL PARTS Secure and raise motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. • Left and right side-covers (to be re-installed with minor modification). • Seat (to be re-installed without modification). • Trunk. • Left and right passenger foot rests (to be re-installed without modification). • Left and right side-covers above passenger foot rests. • Battery and holder (to be re-installed without modification). • Left and right saddle bags (retain side cover mounting grommets for re-use). • Left and right mufflers. • Rear wheel. • Rear brake line to master cylinder.** • Reverse resistor assembly (to be relocated). • Swing Arm (Drive shaft boot will not be used). • Bank angle sensor. • Shocks. Air shock (non coil-over) to be reused. ** Thoroughly vacuum drain rear brake system, including feed line to left front caliper PREINSTALLATION PREPARATION 3.1 Modification to Trunk / Luggage Stay Removal from vehicle frame is not necessary. a. Cut the down tubes of the trunk stay and remove the lower section as shown in Figures 1 & 2 b. Trim rear upper tube-end rounded corners just outboard of welded nut. Trim line should be parallel with center line of vehicle. This will provide clearance for body when installed. Figure 2 (Inset) c. Remove the Hazard and Turn Signal relays from the center holder; bend Relay Holder Tab up 90°. Relays will be relocated to left and right sides. Figure 3 d. Disconnect and remove Bank Angle Sensor from its mount tab (Bank Angle Sensor will not be re-used). Cut wires midway between sensor and plug. e. On plug end, splice / connect red and green wires together to close the circuit. f. Cut and remove the Bank Angle Sensor mount tab from the Trunk stay. Figure 4 3.2 Modification to Rear Inner Fender Removal of fender and attached parts is not necessary for modification. a. Place supplied template (See last page) on fender (left and right sides) as shown and mark outline. With box cutter, cut fender along template outline. Once material is removed, make a vertical cut up the side (line indicated by arrow Figure 5) of the fender. Do not continue cut across top of fender. Figure 5 b. Carefully heat underside of fender with heat gun and bend fender upward until aft end contacts frame cross member. c. Drill holes in plastic fender through cross brace at locations indicated and secure fender to cross with zip ties. Figure 6

HONDA VTX, VTX RETRO AND VALKYRIE DRIVE SHAFT COVER INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 21-12-2010

download
1. Place the cover over the drive shaft housing. 2. Hook one end of the springs provided into the lower holes. Wrap the springs around the backside of the drive shaft housing. Using a needle nose pliers stretch the springs and hook them into the upper holes. 3. Note; if springs are too long, shorten and reform end to be able to hook spring in place.

Incoming search terms: