2001-2003 XV16 Fuel Pump and Carburetor Removal

0

Filed Under (Yamaha) by admin on 31-12-2011

download
Disconnect the carburetor fuel line hose at the fuel pump. •Disconnect the fuel pump wire coupler. •Remove the choke cable from fuel pump bracket. •Remove the upper engine mount, leaving the fuel pump attached to the mount. •Disconnect the TPS and carburetor wire couplers.       Disconnect the throttle cables, and then remove the carburetor. NOTE: The idle adjuster can be removed from its bracket without loosening the bracket screws. PAGE 3 of 12 HIDDEN 6mm SCREW 6mm BOLT UPPER ENGINE MOUNT/ FUEL PUMP CARBURETOR PAGE 4 of 12 Right-Hand Footrest Removal: •Disconnect and remove the brake light switch. •Remove the forward-most tie wrap around the brake hose and frame. •Remove the footrest assembly. NOTE: Leave the brake hose attached. Move the hose to the underside of the foot rest mount and support it as necessary so that it is out of the way Cylinder Head Oil Pipe Removal/ Installation: •Slightly loosen all three banjo bolts before removing them to prevent oil line deformation. NOTE: When loosening the upper banjo bolts, hold the line in place using a wrench at the flat surface on the fitting. Air Injection System (AIS) Removal: •Remove the electric starter motor. •Remove the regulator/rectifier assembly. Remove the AIS pipes from the cylinder head, but leave them attached to the AIS assembly. •Remove the three screws with 8mm heads, and then remove the AIS air filter from the right side. •Remove the three Phillips head screws holding    the AIS assembly on the frame. •Remove the AIS assembly from the left side. FOOTREST ASSEMBLY UPPER BANJO BOLT AIS AIR FILTER AIS ASSEMBLY
PAGE 5 of 12 Transfer Case Removal: •Remove the transfer case bracket first. Then remove the outer chrome cover, inner cover, and drive-sprocket nut. NOTE: There is a sealing washer between the inner case and the transfer case at the 8mm stud. Be sure to replace it during re-assembly. •Remove the two chrome oil lines between the engine and oil tank. NOTE: Retain the four O-rings for re-use. •Remove the drive pulley cover and remove the drive pulley nut. •Loosen the drive belt tension. •Remove the drive pulley, inner cover, collar, and O-ring. NOTE: The collar has a bevel on its inside diameter     for the O-ring facing inward and a bevel on the outside diameter facing the pulley. •Remove the drive and driven sprockets with chain as an assembly. •Remove the collar and O-ring. NOTE: Collar has a bevel on its inside diameter that faces inward for the O-ring. •Remove oil tank filler neck. •Remove the relay bracket on the right-hand side. NOTE: Leave the relays connected. Simply move them out of the way to allow room for transfer case removal. •Slide the transfer case out from the right side.

Incoming search terms:

Honda VT1100 Shadow Guide Plug Patch Repair Manual

0

Filed Under (Honda) by admin on 24-04-2011

download
Find the guide plug.bn The guide plug is shown in the shop manual with the engine removed from the frame and the left crankcase cover removed. (You’ll find this illustration in the “ELECTRIC STARTER/STARTER CLUTCH” chapter in the “STARTER DRIVEN GEAR/STARTER CLUTCH REMOVAL” section.) It’s a little bit harder to find it on the bike. Start by following the yardstick to see where the guide plug is on my bike. To find it on your bike, lie on the ground (or, preferably a mechanics creeper) next to the bike (without the yardstick) and peek under the shift lever and over the frame There it is, just barely visible from the side of the bike. Here’s what a new one looks like: 2. Clean the guide plug and crankcase. From the front of the bike, clean the guide plug and crankcase with brake cleaner in a VERY focused spray. Let the cleaner evaporate before moving to the next step. Page 4 Rev: Draft 5/20/2007 Page 4 of 5 3. Reposition the guide plug. a. From the side of the bike, use the yardstick (or a long screwdriver if you prefer) to gently push the guide plug back into the crankcase. (Note the JB Weld from the previous patch operation.) b. From the front of the bike, gently push upward on the bottom of the upper tab (as shown below) or the bottom of the forward tab to rotate the guide plug into the proper position while maintaining pressure with the yardstick

Incoming search terms:

Yamaha XVS 650AN Supplementary Service Manual

0

Filed Under (Yamaha) by admin on 15-12-2010

download
MAINTENANCE SPECIFICATIONS ENGINE Item Standard Limit Connecting rod: Oil clearance Color code (corresponding size) 0.031 0.055 mm (0.0012 0.0022 in) Blue Black Brown Green CHASSIS Item Standard Limit Front suspension: Front fork travel Fork spring free length Installed length Spring rate (K1) Stroke (K1) Optional spring Oil capacity Oil level Oil grade 140 mm (5.5 in) 332.5 mm (3.1 in) 287.4 mm (11.3 in) 3.43 N/mm (0.343 kg/mm, 19.2 lb/in) 0 140 mm (0 5.5 in) No 0.507 L (17.4 US oz) 95 mm (3.74 in) Yamaha fork oil 10 WT or equivalent 325.9 mm (12.83 in) Front brake: Type Disc outside diameter thickness Pad thickness inner Pad thickness outer Master cylinder inside diameter Caliper cylinder inside diameter Caliper cylinder inside diameter Brake fluid type Single disk 298 5 mm (11.73 0.2 in) 6.0 mm (0.24 in) 6.0 mm (0.24 in) 14.0 mm (0.55 in) 30.2 mm (1.19 in) 33.3 mm (1.31 in) DOT 4 4.5 mm (0.18 in) 0.8 mm (0.03 in) 0.8 mm (0.03 in) Brake lever & brake pedal: Brake lever free play (at pivot) Brake lever free play (at lever end) Brake pedal position Brake pedal free play Clutch lever free play (at pivot) Clutch lever free play (at lever end) 1 2 mm (0.04 0.08 in) 10 15 mm (0.39 0.59 in) 108 mm (4.25 in) 20 30 mm (0.79 1.18 in) 2 3 mm (0.08 0.12 in) 10 15 mm (0.39 0.59 in) -4- MAINTENANCE SPECIFICATIONS SPEC ELECTRICAL Item Standard Limit T.C.I.: Pickup coil resistance/color T.C.I. unit model/manufacturer 182 222 Ω at 20C (68F)/Gray – Black J4T088/MITSUBISHI (U.S.A) J4T128/MITSUBISHI (CAL) Ignition coil: Model /manufacturer Minimum spark gap Primary winding resistance Secondary winding resistance F6T541/MITSUBISHI 6 mm (0.24 in) 3.6 4.8 Ω at 20C (68F) 10.7 14.5 kΩ at 20C (68F) Voltage regulator: Type Model /manufacturer No load regulated voltage Semi-conductor, short-circuit type SH650C-11/SHINDENGEN 14.1 14.9 V Rectifier: Model /manufacturer Capacity Withstand voltage SH650C-11/SHINDENGEN 18 A 200 V Electric starter system: Type Starter motor: Model /manufacturer I.D. number Output Brush overall length Commutator diameter Mica undercut Starter relay: Model /manufacturer Amperage rating Constant mesh type SM-13/MITSUBA SM-13 0.7 kW 10 mm (0.39 in) 28 mm (1.10 in) 0.7 mm (0.08 in) MS-5F-441/JIDECO 180 A 4 mm (0.16 in) 27 mm (1.06 in) Flasher relay: Type Model /manufacturer Self cancelling device Flasher frequency Wattage Semi transistor type FB257H/DENSO Yes 75 95 cycle/min 27 W 2 + 3.4 W Fuel pump relay: Model /manufacturer G8R-30Y-Q/OMRON

2001-2003 YAMAHA XV16 MODELS FACTORY MODIFICATION CAMPAIGN

0

Filed Under (Yamaha) by admin on 02-12-2010

download
Fuel Pump and Carburetor Removal: •Disconnect the carburetor fuel line hose at the fuel pump. •Disconnect the fuel pump wire coupler. •Remove the choke cable from fuel pump bracket. •Remove the upper engine mount, leaving the fuel pump attached to the mount. •Disconnect the TPS and carburetor wire couplers. Disconnect the throttle cables, and then remove the carburetor. NOTE: The idle adjuster can be removed from its bracket without loosening the bracket screws. PAGE 3 of 12 HIDDEN 6mm SCREW 6mm BOLT UPPER ENGINE MOUNT/ FUEL PUMP CARBURETOR PAGE 4 of 12 Right-Hand Footrest Removal: •Disconnect and remove the brake light switch. •Remove the forward-most tie wrap around the brake hose and frame. •Remove the footrest assembly. NOTE: Leave the brake hose attached. Move the hose to the underside of the foot rest mount and support it as necessary so that it is out of the way Cylinder Head Oil Pipe Removal/ Installation: •Slightly loosen all three banjo bolts before removing them to prevent oil line deformation. NOTE: When loosening the upper banjo bolts, hold the line in place using a wrench at the flat surface on the fitting. Air Injection System (AIS) Removal: •Remove the electric starter motor. •Remove the regulator/rectifier assembly. Remove the AIS pipes from the cylinder head, but leave them attached to the AIS assembly. •Remove the three screws with 8mm heads, and then remove the AIS air filter from the right side. •Remove the three Phillips head screws holding the AIS assembly on the frame. •Remove the AIS assembly from the left side. FOOTREST ASSEMBLY UPPER BANJO BOLT AIS AIR FILTER AIS ASSEMBLY PAGE 5 of 12 Transfer Case Removal: •Remove the transfer case bracket first. Then remove the outer chrome cover, inner cover, and drive-sprocket nut. NOTE: There is a sealing washer between the inner case and the transfer case at the 8mm stud. Be sure to replace it during re-assembly. •Remove the two chrome oil lines between the engine and oil tank. NOTE: Retain the four O-rings for re-use. •Remove the drive pulley cover and remove the drive pulley nut. •Loosen the drive belt tension. •Remove the drive pulley, inner cover, collar, and O-ring.

Incoming search terms:

Moto Guzzi Sport 1100i Owners Manual

0

Filed Under (Moto Guzzi) by admin on 29-11-2010

download
General features Identification data Instruments and controls Riding your motorcycle Break-in Maintenance and adjustments Wheel removal Service schedule Cleaning – Storing Cleaning the windscreen Lubrication Valve gear WEBER injectionignition system (I.A.W.) Electrical equipment Wiring diagram Illustrations Lubrication Pressure fed by gear pump. Oil filters: wire mesh inside sump and replaceable cartridge filter outside sump. Normal lubrication pressure 3.8Ö 4.2 [5] kg/cm2, pressure valve, thermostat and cooler. Low oil pressure sensor (electrical) on crankcase. Generator/Alternator On front of crankshaft (1 4V – 25A). Ignition “WEBER MARELLI” electronic digital induced discharge, with high efficiency coil. Spark plugs: Spark plug gap: 0,7 mm. SPORT 1100 DAYTONA R NGK BPR 6 ESI NGK DR9 E IMS Starting Electric starter (12V-1,2 kW) with solenoid engagement. Ring gear bolted on flywheel. Starter button (START) on right of handlebars. Driveline data Clutch Twin driven plates, dry type, on flywheel. Hand controlled by lever on left of handlebars. Primary drive By gears. Ratio: 1 to 1.3529 (tooth ratio 17/23). Gearbox 5-speed, with constantly meshed gears with front dog clutch. Incorporated cush drive. Pedal operated on the left side of the motorcycle. Gear ratios: Low gear = 1 to 1,812 (tooth ratio 16/29) 2nd gear = 1 to 1,250 (tooth ratio 20/25) 3rd gear = 1 to 1 (tooth ratio 23/23) 4th gear = 1 to 0,833 (tooth ratio 24/20) 5th gear = 1 to 0,730 (tooth ratio 26/19) Ratio: 1:4,125 (tooth ratio 8/33) Overall gear ratios (Engine-wheel): Low gear = 1 to 10,1150 2nd gear = 1 to 6,9761 3rd gear = I to 5,5809 4th gear = 1 to 4,6507 5th gear = 1 to 4,0783 Frame Rectangular section single-beam in NiCrMo steel. Semisupporting engine base. Suspensions Front: White Power upside-down hydraulic telescopic fork with individually adjustable rebound and compression; Rear: steel swing arm with oval cross section. Single shock absorber White Power with separate adjustment of spring preload and of hydraulic rebound and compression damping. Wheels Light alloy castings with 3 hollow spokes (rear wheel with cush drive unit). Rim sizes: – front: 3,50x 17 MT H2 – rear: 4,50×17 MT H2 Tires -front: 120/70 ZR 17 – rear: 160/70 ZR 17 [160/60 ZR 17] Type: Tubeless Front: two Brembo drilled semi-floating disc brakes in stainless steel for SPORT I 100; [two Brembo drilled floating discs, Racing type for DAYTONA RS] with fixed 4 differential piston calipers. Adjustable manual control lever on the right side of the handle-bar; – disc 320 mm;

Incoming search terms:

Ninja 250R Motorcycle Service Manual

0

Filed Under (Kawasaki) by admin on 26-11-2010

download
Lubrication It is important to lubricate rotating or sliding parts during assembly to minimize wear during initial operation. Lubrication points are called out throughout this manual, apply the specific oil or grease as specified. Direction of Engine Rotation When rotating the crankshaft by hand, the free play amount of rotating direction will affect the adjustment. Rotate the crankshaft to positive direction (clockwise viewed from output side). Electrical Wires A two-color wire is identified first by the primary color and then the stripe color. Unless instructed otherwise, electrical wires must be connected to those of the same color. Instrument Use a meter that has enough accuracy for an accurate measurement. Read the manufacture’sinstructions thor- oughlybefore using the meter. Incorrect values may lead to improper adjustments. Dimensions Overall Length 2085 mm (82.1 in.) Overall Width 715 mm (28.1 in.) Overall Height 1110 mm (43.7 in.) Wheelbase 1400 mm (55.1 in.) Road Clearance 130 mm (5.1 in.) Seat Height 775 mm (30.5 in.) Dry Mass 152 kg, (335 lb) Curb Mass: Front 82 kg (181 lb) Rear 87 kg (192 lb) Fuel TankCapacity 18.0L (4.8 US gal) Performance Minimum Turning Radius 2.7m (8.9 ft) Engine Type 4-stroke, DOHC, 2-cylinder Cooling System Liquid-cooled Bore AndStroke 62.0×41.2 mm (2.5×1.6 in.) Displacement 249 cm³ (15.2 cuin.) Compression Ratio 11.6 Maximum Horsepower 23.4 kW (31.8 PS) @11 000r/min (rpm), Maximum Torque 22.0N·m (2.24 kg·m, 16.2 ft·lb) @9500 r/min (rpm), Carburetion System Carburetor, Keihin CVK 30×2 Starting System Electric starter Ignition System Battery and coil (transistorized) Timing Advance Electronically advanced Ignition Timing From 10°BTDC@1300 r/min (rpm) 35°BTDC@4000 r/min (rpm) Spark Plug NGKCR8EorNDU24ESR-N Cylinder Numbering Method Left to Right, 1-2 Firing Order 1-2 Valve Timing: Inlet Open 36°BTDC Close 56°ABDC Duration 272° Exhaust Open 61°BBDC Close 31°ATDC Duration 272°

Incoming search terms:

SUZUKI VX800 SPECIFICATIONS AND SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 25-11-2010

download
DIMENSIONS AND DRY MASS Overall length ………………………… 2280 mm (89.8 in) . . . E15, 16, 17, 22, 25, 39 2355 mm (92.7 in) . . . El8 2255 mm (88.8 in) . . . Others Overall width ………………………… Overall height ………………………… Wheel base …………………………… 805 mm (31.7 in) 1115 mm (43.9 in) . . . E03, 28,33 1085 mm (42.7 in) . . . Others 1565 mm (61.6 in) . . . E03,33 1555 mm (61.2 in) . . . Others Ground clearance ……………………… Seat height ………………………….. Dry mass …………………………… 145 mm ( 5.7 in) 800 mm (31.5 in) . . . EOI, 03, 28,33 795 mm (31.3 in) . . . Others 214 kg (472 Ibs). . . E33 213 kg (470 Ibs) . . . Others ENGINE Type ………………………………. Valve clearance ……………………….. Number of cylinders. …………………… Bore ………………………………. Stroke …………………………….. Piston displacement ……………………. Compression ratio …………………….. Carburetor, Front. …………………….. Rear ……………………… Air cleaner ………………………….. Starter system ……………………….. Lubrication system …………………….. Four-stroke, water-cooled, OHC, TSCC, 45″ V-twin 0.08 – 0.13 mm (0.003 – 0.005 in) 2 83.0 mm (3.268 in) 74.4 mm (2.929 in) 805 cm3 (49.12 cu. in) 10.0 : 1 MI KUN I BDS36SS, single MI KUN I BS36SS, single Polyester fiber element Electric starter motor Wet sump TRANSMISSION Clutch …………………………….. Transmission ………………………… Gearshift pattern ……………………… Primary reduction ratio …………………. Gear ratios, Low ……………………… 2nd ………………………. 3rd ………………………. 4th ………………………. Top ……………………… Secondary reduction ratio ……………….. Wet multi-plate type 5-speed constant mesh 1 -down, 4-up 1.690 (71/42) 2.285 (32/14) 1.631 (31/19) 1.227 (27/22) 1 .OOO (25/25) 0.851 (23/27) 1.133 (17/15x 30/30) . . . E03,33 1.096 (17/15x 30/31) . . . Others 3.090 (34/l 1) Final reduction ratio …………………… Drive system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Shaft drive

MOTO GUZZI Quota 1100 ES Specifications And Owner's Manual

0

Filed Under (Moto Guzzi) by admin on 25-11-2010

download
Engine 4-stroke, twin cylinder Cylinder configuration: 90° V-twin Bore: 9 2 mm Stroke: 80 mm Capacity: 1064 cc Compression ratio: 9.5:1 Max. torque: Nm 85 (kgm 8.7) at 3,800 rpm Max. power: Kw 51 (CV 70) a 6,400 rev/min Timing system With rods and rockers and 2 valves per cylinder. One camshaft in the crankcase driven by duplex chain with automatic chain tensioner. Feed system Indirect electronic injection, timed sequential MAGNETI MARELLI IAW 15M “Alfa-N” system, single throttlebody, Weber IW031 injectors, electric pump with pressure regulator, digital control of optimized injection times. Lubrication Pressure fed by gear pump. Wire mesh and cartridge filters on oil sump. Normal lubrication pressure 3.8÷4.2 kg/cm2 (pressure valve on oil sump). Low oil pressure sensor (electrical) on crankcase. Generator / Alternator On front of crankshaft. Output power: 350W at 5000 rev./min. (14V – 25A). Ignition “MAGNETI MARELLI” Inductive discharge digital electronics. Spark plugs: NGK BPR 6 ES. Spark plug gap: 0.7 mm 2 ignition coils Starter Electric starter motor 12V-1.2 Kw with electromagnetic ratchet control. Ring gear on the flywheel. START « » push-button on right handlebar. Transmission Clutch Dry, twin driven plates. Located on engine flywheel. Clutch lever on left handlebar. Primary drive With helical gears, 1:1.3529 (Z=17/23). Gearbox 5-speed, front engaging, constant mesh. Incorporated Cush drive Control pedal on left side of machine. Gear ratios: 1st 1:2 (Z=14/28) 2nd 1:1.3158 (Z=19/25) 3rd 1:1 (Z=23/23) 4th 1:0.8462 (Z=26/22) 5th 1:0.7308 (Z=26/19) Final drive Cardan shaft with gears Ratio: 1:4.125 (Z=8/33) Overall gear ratios (engine-wheel) 1st gear = 1: 11.1618 2nd gear = 1: 7.3433 3rd gear = 1: 5.5809 4th gear = 1: 4.7223 5th gear = 1: 4.0783 Frame Double steel rectangular bar with double cradle

YAMAHA TW200EU/ EUC SPECIFICATION AND SUPPLEMENTARY SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 24-11-2010

download
Model code number: TW200EN: 5FY8 TW200ENC: 5FY9 Dimensions: Overall length 2,090 mm (82.3 in) Overall width 820 mm (32.3 in) Overall height 1,120 mm (44.1 in) Seat height 790 mm (31.1 in) Wheelbase 1,325 mm (52.2 in) Minimum ground clearance 265 mm (10.4 in) Engine: Engine type Air cooled 4-stroke, SOHC Cylinder arrangement Forward inclined single cylinder Displacement 196 cm3 (11.96 cu.in) Bore 〈 stroke 67.0 〈 55.7 mm (2.638 〈 2.193 in) Compression ratio 9.5 : 1 Compression pressure (standard) 900 kPa (9 kg/cm2, 128 psi) Starting system Electric starter Carburetor: Type/manufacturer MV28/TEIKEI Spark plug: Type/manufacturer DR8EA (NGK), X24ESR-U (N.D.) Gap 0.6 ~ 0.7 mm (0.024 ~ 0.028 in) Chassis: Frame type Diamond Caster angle 25.8° Trail 95 mm (3.74 in) Tire: Type With tube Size (F) 130/80-18 66P TW31 Size (R) 180/80-14M/C 78P TW34 Wear Limit <1.0 mm (0.04 in)> Carburetor: ID mark TW200EN: 5FY10 TW200ENC: 5FY00 Main jet (M.J.) TW200EN: #126 TW200ENC: #128 Main air jet (M.A.J.) 1.2 Jet needle-clip/position (J.N) TW200EN: 5B21-1/1 TW200ENC: 5B21-1/3 Main nozzle (M.N.) 2.600 Pilot jet (P.J.) #31 Pilot air jet (P.A.J.) TW200EN: 0.95 TW200ENC: 1.0 Pilot outlet 0.8 Bypass 0.7 Valve seat (V.S.) 1.6 Starter jet (G.S1.) 0.6 (G.S2.) 0.8 Fuel level (above the line on the float chamber mating surface) (F.L.) 0.5 ~ 1.5 mm (0.02 ~ 0.06 in) Float height 10 ~ 11 mm (0.39 ~ 0.43 in) Engine idling speed 1,300 ~ 1,500 r/min Vacuum pressure at idling speed 29.3 ~ 34.7 kPa (220 ~ 260 mmHg, 8.66 ~ 10.24inHg) or more

KTM ATV 525 XC specification

0

Filed Under (KTM) by admin on 12-11-2010

download
Engine ] Pure power for Enduro enthusiasts. The power of the 525 XC is the indisputable benchmark in the ATV Enduro sector. Its acceleration and top speed cast a shadow over all its predecessors. Variable ignition curves and perfect maintenance features like simple valve play adjustment and the removable clutch cover are even further highlights of the XC engine that make the KTM Enduro quads so superior. First Oil Filling for all KTM Engines. [ CarburEttor ] The Keihin carburettor, which has been proven multiple times in racing, with 39 mm and the Throttle Positioning System guarantees a uniform, forceful power delivery in all speed ranges. It ensures an unrivalled response behavior and perfect service-friendliness at all times. [ StartEr ] Packed in a space-saving manner into the free space behind the cylinder head, the small, light electric starter motor is ready for use. It brings every KTM ATV up to speed reliably and comfortably even when racing becomes hectic. [ rEar SuSPENSIoN ] Premium-quality ÖHLINS suspension components specially designed for tough Enduro use are provided as standard – both at the front and the rear. Easy to adjust, they guarantee optimal tuning for the most varied of terrains. Another highlight: the front and rear spring travel of 275 mm and 272 mm respectively is 100 % trend-setting for an Enduro ATV! [ alumINIum SubFramE ] The rear subframe is made of aluminium and is extremely light and easy to remove. [ FramE ] The lightweight, extremely durable frame sets the benchmark in the quad racing segment and is made of high-strength, powder-coated Chromoly steel. [ haNDlEbar ] An ultra-durable tapered aluminium Magura® handlebar comes standard that is four-position adjustable to suit your preferred ergonomics. Further highlights are the functional and individually adjustable operating levers for brake and hydraulic clutch. In addition, the chassis has an integrated mount for a steering damper – available as a PowerPart accessory. [ CurvED raDIator ] Best cooling by means of its curved shape and the resulting maximized surface area. [ rImS / tIrES ] MAXXIS Razr tyres on light, stable DWT aluminium rims. [ ExhauSt ] The powerful XC silencer is made of light-weight aluminium.

Incoming search terms: