CYCLE SOUNDS T-TAP POWER HARNESS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 21-04-2012

download
This t-tap plug is designed to work with Cycle Sounds audio systems. However it can be used to wire many add on 12 volt accessories to you Harley Davidson motorcycle. This plug is rated for 6-8 amps of power and should not be used for adding any product that is rated for more than the t-tap plug is rated for. Take the time to check the products power rating for which you want to install to make sure it is compatible with the t-taps amperage rating. Failure to do so couldlead to electrical failures, which could result in serious injuries or even death. it is possible to overload your motorcycles charging system by adding too many electrical accessories. U se amp meter to verify all power connections. Also check product power ratings for anything you are trying to install. Exceeding the maximum amperage can lead to electrical failures, which could result in serious injuries or even death. INSTRUCTIONS: Step 1: remove seat on bike and locate the wire harness under the seat that matches the plugs on the t-tap harness (2120-0026.) Location may vary between bike models. Step 2: unplug bike harness and snap each end of t-tap harness in correct plug opening. When finished connect power wires to the male plug.(all Cycle Sounds audio systems come pre wired with correct wire colors and terminals). When using this t-tap for any other 12 volt accessory, make sure the red and black wires are snapped into their proper pin connectors. Kit does not come with power terminals for the accessories device. See your local bike dealer for purchase of terminals

TOYOTA ALL MODELS AM STATIC NOISE ON VEHICLES WITH POWER ANTENNAS

0

Filed Under (Toyota Manuals) by admin on 16-10-2011

download
Vehicles with power antennas may exhibit audible electrical noise on weak AM stations when various electrical accessories (turn signals, rear defogger, cruise control, brakes, etc.) are operated. Poor antenna grounding can cause this condition. To eliminate or reduce the intensity of the noise, use the following repair procedure: AM STATIC NOISE ON VEHICLES WITH POWER ANTENNAS Page 1 of 2 OCTOBER 25, 1996 AUDIO AU002-96 ALL MODELS REPAIR PROCEDURE: 1. Tune the radio to a strong, static-free AM station and slowly move the tip of the antenna
mast forward and back approximately 2 inches (Fig. 1). If static noise is not heard, go to Step 2. If static noise is heard during antenna movement, replace the antenna mast and go to Step 3. NOTE: Do not touch the antenna mast with your bare hands. Use a glove or nonmetallic object to move the antenna. (If you touch the antenna with your hands, you will change the antenna sensitivity). 2. Remove the antenna mast and inspect the base of the mast for corrosion and damage (Fig. 2). Clean with 1500 grit sandpaper. 3. Remove the antenna assembly and inspect the inner fender around the antenna hole for corrosion (Fig. 3). Clean with 1500 grit sandpaper.

Incoming search terms:

YAMAH FJR PERIODIC MAINTENANCE AND MINOR REPAIR MANUAL

0

Filed Under (Yamaha) by admin on 22-11-2010

download
Battery The battery is located under panel D. (See page 6-7 for panel removal and installation procedures.) This motorcycle is equipped with a sealed-type (MF) battery, which does not require any maintenance. There is no need to check the electrolyte or to add distilled water. To charge the battery Have a Yamaha dealer charge the battery as soon as possible if it seems to have discharged. Keep in mind that the battery tends to discharge more quickly if the motorcycle is equipped with optional electrical accessories. EW000116 WARNING ● Electrolyte is poisonous and dangerous since it contains sulfuric acid, which causes severe burns. Avoid any contact with skin, eyes or clothing and always shield your eyes when working near batteries. In case of contact, administer the following FIRST AID. •EXTERNAL: Flush with plenty of water. •INTERNAL: Drink large quantities of water or milk and immediately call a physician. •EYES: Flush with water for 15minutes and seek prompt medical attention. ● Batteries produce explosive hydrogen gas. Therefore, keep sparks, flames, cigarettes, etc., away from the battery and provide sufficient ventilation when charging it in an enclosed space. ● KEEP THIS AND ALL BATTERIES OUT OF THE REACH OF CHILDREN. To store the battery 1. If the motorcycle will not be used for more than one month, remove the battery, fully charge it, and then place it in a cool, dry place. 2. If the battery will be stored for more than two months, check it at least once a month and fully charge it if necessary. 3. Fully charge the battery before in- stallation Replacing the fuses The fuse box, which contains the fuses for the individual circuits, is located under panel D. The fuel injection system fuse box is located under panel D. The main fuse box is also located under panel D, beside the battery. (See page 6-7 for panel removal and installation procedures.) If a fuse is blown, replace it as follows. 1. Turn the key to “OFF” and turn off the electrical circuit in question. 2. Remove the blown fuse, and then install a new fuse of the specified amperage.

Incoming search terms: