KTM ELECTRICAL SYSTEMS INSTALLATION, REPAIR

0

Filed Under (KTM) by admin on 02-02-2012

download
DC SYSTEMS STEP DC1 – REGULATOR/RECTIFIER: PRE-2005 KTM If the stock regulator looks like below (the stock connector will not plug into the Trail Tech regulator/rectifier) then the provided stub connector must be soldered into the bike’s wire harness. For models without a stock battery, mount the reg/rec and plug the stub connector into it. Run the red and black wires directly to the (aftermarket) battery, and the yellow wires to the stator. SEE DC CIRCUIT DIAGRAM ON REVERSE SIDE OF PAGE. MODELS WITHOUT A STOCK BATTERY Move stock light to the DC circuit: divert lighting wire from AC circuit to DC circuit. In stock form, the lights are powered by the AC half of the electrical system. In order to continue to use the stock light, find the yellow wire (runs to stock headlight) shown below (wire bundles are found underneath gas tank) and cut the smaller gauge yellow wire. 1. Connect aftermarket light: Wire the light’s red(+) light lead to the positive(+) battery terminal, and the black(-) light lead to the negative(-) battery terminal. Trail Tech lights should use a 10-20 amp fuse as close to the positive(+) battery terminal as possible.

Toyota Camry, 1992-1996 Avalon Repair & Service Manual

0

Filed Under (Toyota Manuals) by admin on 25-05-2011

epair manual covers all Toyota Camry 1992-1996, and Toyota Avalon models, 1995-1996.

Table of Contents

* Introduction: Vehicle identification numbers. Buying parts. Safety. Maintenance techniques. Chemical and lubricants, and more.
* Tune-up and routine maintenance
* Four-cylinder engine
* V6 engines
* General engine overhaul procedures
* Cooling, heating and air-conditioning systems
* Fuel and exhaust systems
* Engine electrical systems
* Emissions control systems
* Transmission

Incoming search terms:

Yamaha VMX12/ VMX12C Owner's Manual

0

Filed Under (Yamaha) by admin on 14-12-2010

download
Main switch EAUO0028 The main switch controls the ignition and lighting systems. The various main switch positions are described below. EAU00032 ON All electrical systems are supplied with power, the headlight, meter lighting, taillight and front position lights come on, and the engine can be started. The key cannot be removed. EAU00038 OFF All electrical systems are off. The key can be removed. 1. Push. 2. Release. 3. Turn P (Parking) The meter light, taillight and position lights are on, but all other electrical sys- tems are off. The key can be removed. The key must be pushed in from the “OFF” position to be turned to “P”. ECA00043 Do not use the parking position for an extended length of time, otherwise the battery may discharge. 1. Neutral indicator light ‘NEUTRAL’ 2. Turn signal indicator light ‘TURN’ 3. Fuel level warning light ‘FUEL’ 4. High beam indicator light ‘HIGH BEAM’ 5. Oil level warning light ‘OIL LEVEL’ EAU03034 Indicator and warning lights EAU00062 Neutral indicator light “NEUTRAL” This indicator light comes on when the transmission is in the neutral position. EAU00059 Turn signal indicator light “TURN” This indicator light flashes when the turn signal switch is pushed to the left or right. his warning light comes on when the fuel level drops below approximately 3 L (0.7 Imp gal, 0.8 US gal). When this occurs, refuel as soon as possible. The electrical circuit of the warning light can be checked according to the fol- lowing procedure. 1. Turn the key to “ON”. 2. If the warning light does not come on, have a Yamaha dealer check the electrical circuit. Oil level warning light “OIL LEVEL” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked according to the following procedure. 1. Turn the key to “ON”. 2. If the warning light does not come on, have a Yamaha dealer check the electrical circuit. NOTE: EAU00064 High beam indicator light “HIGH BEAM” This indicator light comes on when the high beam of the headlight is switched on. Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a mal- function

Incoming search terms:

YAMAHA XT500E, XT600E SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 24-11-2010

download
INSTRUMENT AND CONTROL FUNCTIONS 3 ON OFF LOCK . EAU00040 LOCK The steering is locked, and all electrical systems are off. The key can be removed. To lock the steering 1. Turn the handlebars all the way to the left. 2. Push the key in from the “OFF” position, and then turn it to “LOCK” while still pushing it. 3. Remove the key. To unlock the steering Push the key in, and then turn it to “OFF” while still pushing it. 12 1. Push. 2. Turn.
3-2 INSTRUMENT AND CONTROL FUNCTIONS 3 EAU00056 Indicator lights EAU00063 High beam indicator light ” & ” This indicator light comes on when the high beam of the headlight is switched on. EAU00061 Neutral indicator light “N” This indicator light comes on when the transmission is in the neutral position. EAU00057 Turn signal indicator light ” 5 ” This indicator light flashes when the turn signal switch is pushed to the left or right. 12 3 1. High beam indicator light “&” 2. Neutral indicator light “N” 3. Turn signal indicator light “5 ” EAU00095 Speedometer unit The speedometer unit is equipped with a speedometer, an odometer and a tripmeter. The speedometer shows riding speed. The odometer shows the total distance traveled. The tripmeter shows the distance traveled since it was last set to zero with the reset knob. The tripmeter can be used to estimate the distance that can be traveled with a full tank of fuel. This information will enable you to plan future fuel stops

MECHANIC CERTIFICATION REQUIREMENTS MDOS Form: Repair Facility Manual

0

Filed Under (Tips and Review) by admin on 18-11-2010

download
Chapter 7: Mechanic Certification Requirements Page 4 7-2.2 Heavy-duty Truck Certification Categories. The Heavy-duty Truck Repair categories requiring mechanic certification to repair vehicles over 10,000 pounds G.V.W. are: a) Engine Repair, Gasoline; b) Engine Repair, Diesel; c) Drive Trains; d) Brakes and Braking Systems; e) Suspension and Steering Systems; f) Electrical Systems; g) Collision-Related Mechanical Repair. 7-2.3 Other On-road Vehicle Certification Categories. Repair categories for other on-road vehicles that require mechanic certification to perform repairs are: a) Motorcycle; b) Recreational Trailer. Automobile and Light Truck Certification Categories. The repair categories requiring mechanic certification to repair vehicles under 10,000 pounds gross vehicle weight (G.V.W.) are: a) Engine Repair; b) Engine Tune-up/Performance; c) Front End, Suspension and Steering Systems; d) Brakes and Braking Systems; e) Automatic Transmission; f) Manual Transmission, Front and Rear Drive Axles; g) Electrical Systems; h) Heating and Air Conditioning; i) Collision-Related Mechanical Repair; j) Unitized Body Structural Repair; k) Pre-1973 Vehicle Repair

Incoming search terms:

YAMAHA FZ1 SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 07-11-2010

download
INSTRUMENT AND CONTROL FUNCTIONS 3-1 3 EAU10460 Main switch/steering lock The main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. The various positions are described below. EAU26900 ON All electrical circuits are supplied with power, and the meter lighting, taillight, license plate light and position lights come on, and the engine can be started. The key cannot be removed. NOTE: The headlights come on automatically when the engine is started and stay on until the key is turned to “OFF”, even if the engine stalls. EAU10660 OFF All electrical systems are off. The key can be removed. EAU10680 LOCK The steering is locked, and all electrical systems are off. The key can be re- moved. To lock the steering 1. Turn the handlebars all the way to the left. 2. Push the key in from the “OFF” position, and then turn it to “LOCK” while still pushing it. 3. Remove the key. To unlock the steering Push the key in, and then turn it to “OFF” while still pushing it. WARNING EWA10060 Never turn the key to “OFF” or “LOCK” while the vehicle is moving, otherwise the electrical systems will be switched off, which may result in loss of control or an accident. Make sure that the vehicle is stopped before turning the key to “OFF” or “LOCK”. 1. Push. 2. Turn. 1. Push. 2. Turn.
INSTRUMENT AND CONTROL FUNCTIONS 3-2 3 EAU11003 Indicator and warning lights EAU11030 Turn signal indicator lights “” and “” The corresponding indicator light flashes when the turn signal switch is pushed to the left or right. EAU11060 Neutral indicator light “” This indicator light comes on when the transmission is in the neutral position. EAU11080 High beam indicator light “” This indicator light comes on when the high beam of the headlight is switched on. EAU11250 Oil level warning light “” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir- cuit. NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The

Yamaha YZF R1 SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 07-11-2010

download
INSTRUMENT AND CONTROL FUNCTIONS 3-1 3 EAU10460 Main switch/steering lock The main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. The various positions are described below. EAU10600 ON All electrical circuits are supplied with power, the meter lighting, taillight, license plate light, auxiliary lights and position lights come on, and the engine can be started. The key cannot be re- moved. NOTE: The headlights come on automatically when the engine is started and stay on until the key is turned to “OFF”, even if the engine stalls. EAU10660 OFF All electrical systems are off. The key can be removed. EAU10680 LOCK The steering is locked, and all electrical systems are off. The key can be re- moved. To lock the steering 1. Turn the handlebars all the way to the left. 2. Push the key in from the “OFF” position, and then turn it to “LOCK” while still pushing it. 3. Remove the key. 1. Push. 2. Turn. INSTRUMENT AND CONTROL FUNCTIONS 3-2 3 To unlock the steering Push the key in, and then turn it to “OFF” while still pushing it. WARNING EWA10060 Never turn the key to “OFF” or “LOCK” while the vehicle is moving, otherwise the electrical systems will be switched off, which may result in loss of control or an accident. Make sure that the vehicle is stopped before turning the key to “OFF” or “LOCK”. EAU11003 Indicator and warning lights EAU11030 Turn signal indicator lights “” and “” The corresponding indicator light flashes when the turn signal switch is pushed to the left or right. EAU11060 Neutral indicator light “” This indicator light comes on when the transmission is in the neutral position. EAU11080 High beam indicator light “” This indicator light comes on when the high beam of the headlight is switched on. EAU11250 Oil level warning light “” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir- cuit. NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction