2007 Corolla & Matrix 1ZZ-FE ENGINE NO START CONDITION REPAIR

0

Filed Under (Toyota Manuals) by admin on 01-11-2011

download
Refer to TIS, 2007 model year Corolla or Matrix Repair Manual: Engine Hybrid System – Engine Control – “1ZZ-FE Engine Control System: ECM: Removal” Engine Hybrid System – Engine Control – “1ZZ-FE Engine Control System: ECM: Installation” 2. Register the VIN into the replacement ECM (PCM). Refer to TIS, 2007 model year Corolla or Matrix Repair Manual: Engine Hybrid System – Engine Control – “1ZZ-FE Engine Control System: SFI System: Registration Some 2007 model year Corolla and Matrix vehicles equipped with a 1ZZ-FE engine may exhibit a “no start” condition. Improvements have been made to the Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) manufacturing process to reduce the possibility of this condition occurring. Please use the following procedure to repair the vehicle

Incoming search terms:

Toyota Engine Control Module (ECM) Parts Information

0

Filed Under (Toyota Manuals) by admin on 20-10-2011

download
2005-2008 Corolla Engine(s): 1ZZ Transmission(s): 5MT, 4AT VDS(s): BR30E, BR32E 2005-2008 Matrix Drive Type(s): 2WD Engine(s): 1ZZ Transmission(s): 4AT, 5MT VDS(s): KR30E, KR32E Introduction The purpose of this TSB is to provide the Engine Control Module/ECM (SAE term: Power train Control Module/PCM) parts information necessary for proper identification and vehicle application. A vehicle with an incorrect ECM (PCM) installed may cause one or both of the following conditions: •M.I.L. “ON”DTCP0741-Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve SL). •Failureto complete On-Board Diagnostic (OBDII) Readiness Monitors. NOTE If the part number is correct, the ECM (PCM) is NOT the cause of the DTC or OBDII Readiness Monitor concern.

2001-2003 GL1800/ A ECM Replacement/ Cooling System REPAIR PROCEDURES

0

Filed Under (Honda) by admin on 29-01-2011

download
Install the new ECM, then reinstall the cruise/ reverse control module in the reverse order of removal. NOTE: When you start the vehicle – after completing ALL procedures – the new ECM will require initialization . To initialize the new ECM, perform the following procedure: • Start the bike and allow it to warm up to normal operating temperature and remain at idle for at least 90 seconds . Do not operate the throttle during this time; if you do, the ECU will not initialize properly and the process will need to be repeated. 5. Proceed to the Cylinder Head Inspection section below. Use the Cylinder Head Inspection Kit for the Cylinder Head Inspection procedure. Use the kit for each GL1800/A you inspect. Do NOT dispose of kit items. 1) 19X20 mm cap (2) (cap B) 2) 8X15 mm cap (cap A) 3) Hose plug 4) Bottle/cap w/feed hose 5) Harness clips (10) 6) Harness tape 7) Inspection mirror A limited number of additional Cylinder Head Inspection Kits are available: call TechLine at 800-421-1900, ext. 1 if you need one. Kit contents are NOT available separately as parts. NOTE: • The following late ’03 models do not have to have their cylinder heads inspected: • Perform the following procedure with the engine at room temperature. • Both Left and Right cylinder heads must be inspected. • Use the Cylinder Head Inspection Kit for the following procedure. 1. Remove the front lower fairing. (See S/M, 2-6) 2. Remove and suspend the rear brake reservoir, being careful not to stress the brake hose. (See S/M, 15-A-8) CONNECTOR B (22-GRY) CONNECTOR C (6-BLK) CONNECTOR A (22-BLK) ECM (ENGINE CONTROL MODULE) 1 2 3 4 5 6 7 Late ’03 (Non-ABS): after VIN 1HFSC470*3A204632 Late ’03 (ABS): after VIN 1HFSC474*3A201020 Cylinder Head Inspection Kit Cylinder Head Inspection

Incoming search terms:

Incoming search terms: