DUCATI MONSTER 1100 / 1100S Owner's manual and maintenance manual

0

Filed Under (Ducati) by admin on 14-12-2010

download
1) Speedometer . Indicates road speed. 2) Odometer . Shows total distance travelled. 3) Trip meter . Indicates the distance travelled since last reset. 4) Fuel reserve trip counter . Shows distance travelled on reserve fuel. 5) Clock . ) Lap time . 7) Rev counter (RPM) . 8) Lap time . 7 10 12 11 13 9 4 5 8 2 3 1 6 fig. 6 14 E 9) Service indicator (fig. 6). The indicator illuminates to signal when a service is due. The service indicator will remain on the display until the system is reset by the Ducati Service Centre whocarry outthe service. 10) LAP function (fig. 6). Indicates that the LAP has been activated. 11) DDA function (fig. 6). Indicates that the Ducati Data Analyzer (DDA) has been activated. Important The instrument panel incorporates diagnostic functions for the electronic injection/ignition system. The related menus are for use by trained personnel only. If you accidentally access this function, turn the key to OFF and have the motorcycle checked at an authorized Ducati Service Centre. 12) Oil temperature indicator (fig. 6). Important Stop riding if the temperature reaches the maximum value, otherwise the engine might be damaged. 13) Ducati Traction Control (DTC) (fig. 6). Indicates activation of the DTC control unit (if present). 15 E LCD – How to set/display parameters At key-on (key turned from OFF to ON ) the instrument panelactivates all the digits of the LCD for 1second and switches on the indicator lights in sequence. OFF CHECK 1 fig. 7 16 E It then reverts to “normal” mode and, in place of the motorcycle speed, shows the model and, for 2 seconds, alsothe version (EU, UK, USA, CND, FRA, JAP). The model is scrolled on the display onceonly. CHECK 2 RUN fig. 8 17 E At Key-On, the instrument panel always shows the following information (de-activating any previously activated functions): Odometer Speed Engine rpm bargraph Engine oil temperature bargraph At this point, with button (1, fig. 9) in position B “▼” it is possible to switch from the odometer display function to thefollowing functions: TRIP TRIP FUEL (only if active) Clock before returning to TOT (odometer function). If, however, you press switch (1, fig. 9) in position A “▲”, thesystem enters MENU mode and displays the following functions in sequence: Error (only if active) BATT RPM LIGHT SET LAP (OFF or ON) LAP MEM DDA (OFF or ON) Erase DDA TIME Set CODE (only if active)

YAMAHA FJR1300N OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 12-12-2010

download
3-2 3 EAU03034 Indicator and warning lights EAU04121 Turn signal indicator lights “” a n d “” The corresponding indicator light flashes when the turn signal switch is pushed to the left or right. EAU00061 Neutral indicator light ” ” This indicator light comes on when the transmission is in the neutral position. EAU00063 High beam indicator light ” ” This indicator light comes on when the high beam of the headlight is switched on. EAU03201 Oil level warning light ” ” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked according to the fol- lowing procedure. 1. Set the engine stop switch to ” ” and turn the key to “ON”. 2. Shift the transmission into the neu- tral position or pull the clutch lever. 3. Push the start switch. If the warning light does not come on while push- ing the start switch, have a Yamaha dealer check the electrical circuit. NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a mal- function. EAU03192 Engine trouble warning light ” ” This warning light comes on or flashes when an electrical circuit monitoring the engine is defective. When this oc- curs, have the Yamaha dealer check the self-diagnosis system. The electrical circuit of the warning light can be checked according to the fol- lowing procedure. 1. Set the engine stop switch to ” “. 2. Turn the key to “ON”. If the warn- ing light does not come on, have a Yamaha dealer check the

Incoming search terms:

HONDA CRF250R OWNER'S MANUAL AND COMPETITION HANDBOOK

0

Filed Under (Honda) by admin on 04-12-2010

download
Before Riding 9 Is Y our Motorcycle Ready to Ride? Competitive riding can be tough on a motorcycle, so it’s important to inspect your CRF and correct any problems you find before each ride. Check the following items (page numbers are at the right): Pre-ride Inspection Check the following before each ride: • Engine oil level ……………. ……………. ………….37 •T ransmission oil level……….. ……………. ……..40 • Coolant for proper level……….. ……………. …..41 • Cooling system and hoses for condition……. 42 • Spark plug for proper heat range, carbon fouling and high tension cord terminal for looseness ……………. ……………. ……………. …….55 • Air cleaner for condition and contamination… ……………. ……………. ………….43 • Clutch lever adjustment and freeplay ………..49 • Hot start lever freeplay ……………. ……………. .54 • Breather drain for cleaning ……………. ………..45 • Steering head bearing and related parts for condition……. ……………. ……………. ………..91 • Carburetor throttle operation ……………. ……..47 •T yres for damage or improper inflation pressure ……………. ……………. ……………. ……..82 • Spokes for looseness……. ……………. …………..81 • Rim locks for looseness……. ……………. ………81 • Front and rear suspension for proper operation ……………. ……………. ……………. .72, 73 • Front and rear brakes, check operation ……..77 • Drive chain for correct slack and adequate lubrication ……………. ……………. ……………. …..84 • Drive chain guide, sliders and drive chain rollers for damage or wear……… ………….84, 85 • Exhaust pipe/Muffler inspection…… ………….87 • Steering damper operation inspection ……….91 • Every possible part for looseness (such as cylinder head nuts, engine mounting bolts/nuts, axle nuts, handlebar holder bolts, fork bridge pinch bolts, drive chain adjuster, drive chain guide, wire harness connectors, kickstarter mounting bolt) ……………. 148 -

HONDA PHANTOM OWNER'S MANUAL

0

Filed Under (Honda) by admin on 01-12-2010

download
MOTORCYCLE SAFETY 1 Safe Riding Rules 2 Protective Apparel 2 Modifications 3 Loading and Accessories 6 PARTS LOCATION 9 Instruments and Indicators 11 MAJOR COMPONENTS (Information you need to operate this motorcycle) 11 Suspension 12 Brakes 16 Clutch 18 Fuel 22 Engine Oil 23 Tubeless Tyres 26 ESSENTIAL INDIVIDUAL MPONENTS 26 Ignition Switch 27 Right Handlebar Controls 28 Left Handlebar Controls FEATURES (Not required for operation) 29 Steering Lock 30 Helmet Holder 31 Side Cover 32 Document Compartment 33 Seat 34 Headlight Aim Vertical Adjustment 35 OPERATION 35 Pre-ride Inspection 36 Starting the Engine 39 Running-in 40 Riding 42 Braking 43 Parking 43 Anti-theft Tips MAINTENANCE 44 MAINTENANCE 45 Maintenance Schedule 48 Tool Kit 49 Serial Numbers 50 Maintenance Precautions 51 Air Cleaner 52 Crankcase Breather 53 Engine Oil 56 Spark Plugs 58 Throttle Operation 59 Idle Speed 60 Drive Chain 66 Front and Rear Suspension Inspection 66 Side Stand Page 67 Brake Pad Wear 69 Wheel Removal 74 Battery 77 Fuse Replacement 79 Stoplight Switch Adjustment 80 Bulb Replacement 84 CLEANING 86 STORAGE GUIDE 86 Storage 88 Removal From Storage 89 SPECIFICATIONS 92 CATALYTIC CONVERTER MOTORCYCLE SAFETY

HONDA CRF250X OWNER'S MANUAL

0

Filed Under (Honda) by admin on 01-12-2010

download
Always follow the proper starting procedure described below. Your motorcycle can be kickstarted wirh the transmission in gear by pulling in the clutch lever before operating the kickstarter. Preparation Make sure that the transmission is in neutral. Turn the fuel valve ON. Fuel Valve Starting Procedure Always follow the proper starting procedure described as follow. 4. Warm up the engine; don’t operate the throttle. 5. About 15 seconds after the engine startes, push the choke knob back all the way to fully OFF. If idling is unstable, open the throttle slightly. Extended use of the choke may impair piston and cylinder wall lubrication and damage the engine. High Air Temperature 35°C (95°F) or above 1. Do not use the choke. 2. Keep the throttle fully closed. 3. Start the engine following step 3 under Normal Air Temperature. Low Air Temperature 10°C (50°) or below 1. Follow steps 1-4 under Normal Air Temperature. 2. Continue warming up the engine until it runs smoothly and responds to the throttle when the choke knob is pushed back all the way to fully OFF. Extended use of the choke may impair piston and cylinder wall lubrication and damage the engine. Hot Engine Starting 1. Pull the hot start lever (3) and start the engine following step 3 under Normal Air Temperature. 2. As soon as the engine starts, release the hot start lever. NOTICE NOTICE Basic Operating Instructions 15 (1) fuel valve The three-way fuel valve is used to control the flow of fuel from the fuel tank to the carburetor. ON -Turning the fuel valve ON before attempting to start the engine allows fuel to flow from the fuel tank to the carburetor. OFF -Turning the fuel valve OFF after stopping the engine prevents the flow of fuel from the fuel tank to the carburetor. RES -Turning the fuel valve to RES allows fuel to flow from the reserve fuel supply to the carburetor. (1) fuel valve (2) choke knob Check the engine oil, transmission oil and coolant levels before starting the engine (pages 44,47,48). To restart a warm engine, follow the procedure for ”High Air Temperature. ” Normal Air Temperature 10°C-35°C (50°F-95°F) 1. Pull the choke knob (2) up all the way to fully ON, if the engine is cold. 2. Keep the throttle fully closed. 3. Pull the clutch lever all the way in, and press the starter button with the throttle completely closed. Or operate the kickstarter to start the engine. Starting from the top of the stroke, kick through to the bottom with a rapid, continuous motion. Do not operate the throttle. Allowing the kickstarter to snap back freely against the pedal stop can damage the engine case.

Incoming search terms:

APRILIA RSV 1000 R – RSV 1000 R FACTORY Workshop manual

0

Filed Under (Aprilia) by admin on 29-11-2010

download
LUBRICANTS DANGER A good lubrication ensures the vehicle safety. Failure to keep the lubricants at the recommended level or the use of a non-suitable new and clean type of lubricant can lead to the engine or gearbox seizure, thus leading to serious accidents, personal injury or even death. Gear oil may cause serious damage to the skin if handled daily and for long periods. Wash your hands carefully after use. Do not dispose of oil into the environment. Take it to the filling station where you usually buy it or to an oil salvage center. WARNING When filling the vehicle with this oil, take care not to spill it out since it could damage the vehicle paint- work. In case of contact with oil, the tyres surface will become very slippery, thus becoming a serious danger for your safety. In case of leaks, do not use the vehicle. Check and trace the cause of leaks and proceed to repair. ENGINE OIL DANGER Prolonged or repeated contact with engine oil may cause severe skin damage. Wash your hands thoroughly after handling engine oil. Do not release into the environment. Dispose of engine oil through the nearest waste oil reclamation firm or through the supplier. Wear latex gloves during servicing FRONT FORK FLUID DANGER Front suspension response can be modified to a certain extent by changing damping settings and/or selecting a particular grade of oil. Standard oil grade is SAE 20 W. Different oil grades can be selected to obtain a particular suspension response. (Choose SAE 5W for a softer suspension, 20W for a stiffer sus- pension). The two grades can also be mixed in varying solutions to obtain the desired response. GENERAL INFORMATION 1 -9 RSV 1000 R – RSV 1000 R FACTORY BRAKE FLUID NOTE This vehicle is fitted with front and rear disc brakes. Each braking system is operated by an independent hydraulic circuit. The information provided below applies to both braking systems. DANGER Do not use the vehicle in case brakes are worn out or do not work properly! The brakes are the parts that most ensure your safety and for this reason they must always be perfectly working. Failure to comply with these recommendations will probably lead to a crash or an accident, with a consequent risk of personal injury or death. A wet surface reduces brakes efficiency.

Incoming search terms:

ROKON Illustrated Owners and Parts Manual

0

Filed Under (Rokon) by admin on 28-11-2010

download
Front and Rear Brake. Check brake action. Check pucks to see that they are not over worn. There should be visible brake material on both sides of the brake disc. See Section 6. Fuel Tank. Check fuel level. Fill as necessary. Use super unleaded for altitudes above 10,000 ft. Engine Oil. The engine holds .6 qt. of SAE10W30/40 motor oil. Fill to the dipstick “full” line. Miter Box and Transmission. They are fi lled at the factory and need not be checked at the start. The miter box should have 2.5 oz. of EP 80W90 gear lube oil. The transmission takes 6 oz. of EP 80W90 gear lube oil. The transmission has a fi ll to plug near the bottom of the transmission( shown on page 46). There is no fi ll level for the miter box. Over fi lling of either the miter box or transmission will result in leakage. Throttle. Check for proper throttle cable operation. Look for smooth response to twist action. Wheels and Tires. Check Tire pressure, wear and damage. Fittings and Fasteners. Check all fi ttings and fasteners. Drive Chains. Check chains for tension and lubrication. Adjust tension for 1/2″ – 3/4″ defl ection at mid point. Engine Manual. Read your engine manual completely and follow all instructions

ENGINE ASSEMBLY MANUAL 450i, ENGINE REPAIR STAND – 450i

0

Filed Under (Tips and Review) by admin on 28-11-2010

download
INSTALLING THE CLUTCH : æ Install the bronze bushing, the clutch basket, the spacer washer and the clutch hub. Install the conical washer, apply thread locking material to the threads and install the nut. Use tool #R447 to hold the assembly and tighten the nut to 150 Nm . æ Soak the friction discs in engine oil prior to installation. Alternatively install a friction disc followed by a metal disc until they are all installed, the last disc to be installed will be a friction disc. Install the clutch actuating rod, the clutch lifter piece, the needle thrust bearing and the thrust washer. Install the pressure plate, the six springs, the six washers and the six screws. Tighten the screws to 11 Nm . Tool #R447
Page 8 sur 26 æ Install the two locating dowels, install a new gasket, and note that Sherco uses a special gasket with an integrated silicone bead. Do not use gasket sealer on the mating surfaces as the sealer could plug the oil passages. Install the clutch cover and tighten the twelve screws to 11 Nm . o INSTALLING THE CAM CHAIN DRIVE GEAR ON THE LEFT HAND SIDE OF THE CRANKSHAFT: æ Using a thermal heat gun, heat the cam chain drive gear to ≈ 100°C , install the gear on the LH side of the crankshaft after installing the key, install the circlip. Use care to avoid damage to the end of the crankshaft. Page 9 sur 26 o INSTALLATION OF THE CYLINDER : æ Use a sharp chisel to remove any of the metal gasket that protrudes above the cylinder mounting surface.

BMW K1300S Rider's Manual

0

Filed Under (BMW) by admin on 27-11-2010

download
General view, right side 1 Engine oil level indicator (101) 2 Fuel filler opening (79) 3 Battery compartment (127) 4 Brake-fluid reservoir, front (102) 5 Vehicle identification number (ontheupperfront wheel control) 6 Type plate (on rear cross tube) 7 Brake-fluid reservoir, rear (105) 2 13 z Overviews Left handlebar fitting 1 High-beam headlight and headlight flasher (55) 2 Operating odometer (49) with onboardcomput- erOE Operating onboard computer (51) 3 Hazard warning flashers (56) 4 Operating turn indicators (56) 5 Horn 6 with Electronic Suspen- ionAdjustment (ESA II)OE Operating ESA (64) 7 ABS operation (58) with automatic Stability ControlOE Operating the ASC (59) 2 14 z Overviews Handlebar fitting, right 1 with heated handlebar gripsOE Heated handgrips (60) 2 Starter button (72) 3 Emergency ON/OFF switch (57) 2 15 z Overviews Underneath seat 1 Luggage loops 2 Rider’sManual (US Model) 3 Tire inflation pressure table 4 Payload table 5 Helmet holder (68) 6 Toolkit (100) 7 Engine oil fill location (102)

KINROAD 150 SERVICE MANUAL

0

Filed Under (Kinroad) by admin on 27-11-2010

download
FUEL AND OIL RECOMMENDATIONS Be sure to use the specified fuel and oil. FUEL Gasoline should SAE 90# or higher. Unleaded gasoline is recommended. ENGINE OIL SAE10W-30 engine oil of high quality should be used. BREAK-IN PROCEDURE For the first 2 hours of riding, do not exceed 2/3 throttle. Vary engine speed for the first 5 hours. Never hold engine at full throttle for long periods of time. SPECIFICATIONS DIMENSIONS DOUBLE SEAT/SINGLE SEAT Overall Length 2159mm/2075mm Overall Width 1400mm/1235mm Overall Height 1470mm/1400mm Wheelbase 1499mm/1450mm Ground Clearance 170mm/130mm ENGINE Type Forced air-cooled, single cylinder, 4-Stroke Engine Capacity 150cc Displacement 149.5cc Bore x Stroke 57.4mm x 57.8mm Compression Ratio 9.2:1 Max Power 7.4kw/7500rpm Max Torque 9.5N.m/5500rpm Fuel Type SAE 90# or above (unleaded) Lubricate Oil SAE 10W/30 Ignition C.D.I. Starting Electric Spark Plug C7HSA (NGK) Transmission Automatic C. V. T. Carburetor MIKUNI, BS24J Lubrication Force & Splash

Incoming search terms: