YAMAHA DT125RE/ X SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 27-11-2010

download
OIL WARNING LIGHT CHECKING METHOD Main Switch “ON” Gears in “NEUTRAL” Oil warning indicator light does not come on Refeer to CHAPTER 8 “SIGNAL SYSTEM” Oil warning indicator light come on Shift into gear Oil warning indicator light does not come on Oil warning indicator light come on Supply engine oil Engine oil level and electrical circuit are OK 1 CHK ADJ TRANSMISSION OIL LEVEL INSPECTION/ TRANSMISSION OIL REPLACEMENT 3-11 TRANSMISSION OIL LEVEL INSPECTION 1. Inspect: •transmission oil level Oil level low **Add sufficient oil ******************************** Transmission oil level steps: •Place the machine on a level surface. •Warm up the engine for several minutes and stop it. •Visually check the oil level through the level window *. NOTE: •Check the oil level just one minute after stopping the engine. •The oil should e confirmed between maximum *and minimum *marks. •If the oil level is lower, add sufficient oil to raise it to the proper level. •Do not add any chemical additives. Transmission oil also lubricates the clutch and additives could cause clutch slippage. •Be sure no foreign material enters the crankcase. **************** **************** TRANSMISSION OIL REPLACEMENT 1. Warm up the engine for several minutes. 2. Place a container under the engine. 3. Remove: •oil filler cap * •drain pulg * drain transmission oil. NOTE: Drain the transmission oil with the motorcycle slightly inclined to the right. 4. Inspect: •gasket (Drain plug) •O-Ring (oil filter cap) Damage **Replace

SUZUKI VZR1800K6 And VZR1800/ ZK7 FUEL DELIVERY PIPE REPLACEMENT

0

Filed Under (Suzuki) by admin on 26-11-2010

download
NOTE: The fuel delivery pipe assembly can be removed from the throttle body without removing the throttle body assembly from the motorcycle. 1) Refer to section 6 of the service manual to remove the fuel tank and the air cleaner box. Place shop rags over the bore of each throttle body to prevent anything from falling into the engine through the throttle bodies. 2) Remove the wire harness clamp, disconnect the fuel injector couplers A and move the harness aside. 3) Remove the four fuel delivery pipe assembly mounting screws and remove the fuel delivery pipe assembly. 4) Replace the o-rings and seals with the new parts supplied in the kit (apply a small amount of engine oil to the o-rings and seals to ease the installation of the injector). To prevent damage to the o-rings or seals, don’t turn the injector when pushing it into the fuel delivery pipe and throttle body respectively. Install the new fuel delivery pipe assembly in the reverse order of removal. 5) Connect the fuel injector couplers A and clamp the injector harness to the fuel delivery pipe. DO NOT overtighten the harness clamp. 6) Connect the fuel tank, remove the shop rags from over the bore of each throttle body, and run the engine, checking for fuel leaks. DO NOT reuse the original fuel hose connector retainer. Confirm that the fuel hose connector has completely seated and locked (clicked) into position before turning on the ignition switch. 7) Refer to section 6 of the service manual to install the air cleaner box and the fuel tank. 8) Test ride the motorcycle to confirm proper operation. FUEL DELIVERY PIPE ASSEMBLY REPLACEMENT PROCEDURE

Wildfire Scooter WF 250CB Owner's Manual

0

Filed Under (Uncategorized) by admin on 26-11-2010

download
• Check before Riding • Make sure the brakes work properly and adjust if necessary. • Check all nuts and bolts for tightness. • Make sure that the gas tank is full. • Check tire pressure. • Check all gauges. • Check and make sure that all of the lights are working properly, headlight, taillight, turn signal etc. • Check the engine oil. STARTING, RIDING, STOPPING AND PARKING Before starting, put the kickstand up. • Practice in an empty area away from people and vehicles. • Always remember to obey your local and state laws and regulations. • Be sure your bike has fuel and oil. • Be sure the bike is in neutral. • Apply the rear brake. • Turn the key on. • Press the electric start button. • After engine warms up, push the choke 1/4 in then 1/2 in and in 1 minute completely off. • If the engine is warm it should start without choking. • For a cold engine, let the engine idle for 1-3 minutes before driving, then begin to turn the choke off. • Never exceed 4 seconds when engaging the starter. • Release the button immediately after the engine starts. • Do not apply the key while the engine is running, it can cause damage to the starter. • Sit on the bike keeping one foot on the ground for stability, release the clutch by pulling in the lever, shift bike into first gear by using the foot shifter. • Apply the throttle gradually as you release the clutch lever slowly until the clutch engages. • To shift into the next gear release the throttle pull the clutch lever in and shift into the next gear, after you shift, gradually apply the throttle and slowly release the clutch. • Use this sequence when shifting to all gears. • Only put your feet on the ground when coming to a stop. • When coming to a stop decrease your speed by releasing the throttle and applying the brakes and the clutch, if the tire skids release the brake and reapply. • Parking: Put your kick stand down. Park away from pedestrians. NOTE: The muffler and exhaust pipe are h

Baja SC50 SCOOTER OWNER'S MANUAL

0

Filed Under (Bajaj) by admin on 26-11-2010

download
Engine oil level a) Check for leaks b) Tighten filler cap securely. c) Add oil if required. 2. Fuel level a) Add fuel as necessary. b) Do not overfill (no fuel in the filler neck). c) Do not mix oil with gas. d) Replace cap tightly. e) Do not refuel a hot engine. Allow engine to cool before adding fuel. 3. Warning decals a) Make sure all warning decals are legible and securely attached. b) Replace as necessary. 4. Tires a) Ensure that both tires have at least 1/8 in. tread depth at center. b) Both tires must be inflated to the pressure indicated on the tire sidewalls. c) Replace the tires id tread height is less then 1/8 in. at the center of tires. 5. Drive chain a) Check condition and tension. b) Lubricate and adjust tension as necessary. 6. Throttle a) Check for smooth operation. Make sure the throttle “snaps” back to idle. b) Check for frayed cable or damaged cable housing. Replace damaged cable. c) Check for mud, debris and ice in the throttle cable/mechanism. Clean out any contamination.

APRILIA QUASAR 50-100-125-180 maintenance Manual

0

Filed Under (Aprilia) by admin on 26-11-2010

download
CHANGING ENGINE OIL CAUTION In case of oil leakage or malfunctions, contact an Aprilia Authorised Dealer . Do not dispose of oil in the environ- ment. Dispose of engine oil – stored in a sealed container – through the nearest waste oil reclamation firm or through the supplier. Carefully read page 34 (MAINTE- NANCE) To change engien oil: ◆ Ride for a few kilometres until engine reaches the operating temperature, then stop the engine. ◆ Position a graduated container (1), under the drain plug (2). ◆ Loosen oil filler plug (4) and drain plug (2). ◆ Let oil flow out of the sump. ◆ Loosen oil filter (3) and carefully clean it. ◆ Refit the filter and tighten fully. ◆ Tighten drain plug (2) and pour recommended oil into filler plug (4), see page 58 (LUBRICANT CHART). ◆ Tighten the filler plug. CAUTION Carefully tighten filler and drain plugs and ensure oil does not leak out. Periodically check for leaks at the casing cover gasket. Do not use the vehicle with insufficient lubrication or with contaminated or unsuitable lubricants, since this would cause early wear of the moving parts and may also cause irreparable failures Fluid reservoir (1) is under rear right wheelhouse. CAUTION Position the vehicle on firm and flat ground. ◆ Make sure that the fluid contained in the reservoir exceeds the ” MIN ” mark stamped on the reservoir. MIN = minimum level. WARNING Do not use the vehicle if the braking system is leaking fluid. CAUTION Do not use the vehicle if the fluid is below the “MIN” mark. 1
27 use and maintenance Quasar 50 – 100 – 125 – 180 CAUTION Brake fluid level decreases as the brake pads wear down. Should the level be too low: ◆ Check the brake discs and pads for wear, see page 27 (CHECKING THE BRAKE PADS FOR WEAR) If the pads and/or the disc do not need re- placing: ◆ Contact an Aprilia Authorised Dealer that will top up the fluid. WARNING Check the brake for proper operation. When the brake lever has exceeding travel or if you notice a loss of braking, contact an Aprilia Authorised Dealer . The braking system may need bleed- ing. CHECKING THE BRAKE PADS FOR WEAR Carefully read page 26 (BRAKE FLUID – recommendations) , page 26 (DISC BRAKES) and page 34 (MAINTE- NANCE). Periodically check brake pad wear. The rate at which brake pads will wear depends on vehicle usage, riding style and road surface condition. Outlined below is a quick brake pad inspection procedure: ◆ Visually check between brake disc and pads, check both pads (1) looking from the bottom at the rear end. ◆ Should friction material (of even one pad only) be worn down to 1.5 mm of thickness, have both pads replaced

Baja BA 250 ATV OWNER'S MANUAL

0

Filed Under (Bajaj) by admin on 26-11-2010

download
FUEL AND OIL FUEL Proper fuel is very important for the engine. Ensure there is no dust, dirt, or water which has mixed in the fuel. Use regular unleaded gasoline with an octane number 90 or higher. ENGINE OIL Your 250cc ATV has a four-stroke engine. Please use oil as described in the chart below. By using prescribe oil, you will realize the best lubrication for engine. Use the chart to select a viscosity rating based on the temperature range in your area. NOTE: In very cold weather (below 5°F (-15°C), use SAE10W-30 for good starting and smooth operation. SAE 10W-30 SAE 20W-40 ENGINE TEMP. °C °F -30 -22 40 104 -10 14 0 32 10 50 20 68 30 86 -20 4 FUEL AND OIL 8 LOCATION OF LABELS Read and follow all of the warnings labels on your ATV. Make sure you understand all the labels. Keep the labels on the ATV. Do not remove them for any reason. If a label comes off or becomes difficult to read, you should get a replacement by contacting BAJA INC. 1 – Red Light – Reverse indicator Light illuminates when ATV is in Reverse. 2 – Green Light – Neutral indicator Light illuminates when ATV is in Neutral. 3 – Ignition key switch – Turn right (CW) “RUN”, Turn left (CCW) “OFF”. ATV will only start when ignition key is turned to the “RUN” position. Make sure ignition key switch is in the “OFF” position when not in use

Incoming search terms:

Wangye WY250T SPECIFICATION AND USER MANUAL

0

Filed Under (Wangye) by admin on 25-11-2010

download
item Data Item Data L×W×H mm 2015×680×1210 Front Tyre T 130/160-13 Wheelbase mm 1350 Rear Tyre 110/180-10 Ground Clearance mm 101 Air Pressure of Fr tyre 200 kPa Dry weight kg 160kg Air Pressure of Rr tyre 250 kPa Max Load kg 150kg Transmission system CVT Turning angle of steering handle ≤48° Ratio 5.12~15.05 Brake base mm ≤7(30km/h) Engine Type 169MM Single Cylinder、4 stroke、 water-cooled Max Speed km/h ≥85km/h Bore×stroke mm 69×66.8 Consumption L/100km ≤3.1L/100km Displacement ml 249.8 Climb ability º ≥18 Clutch automatically centrifugal Light vertical angle -1.3% Fuel tank L 7 Starting system Electric Battery 12V 9Ah – 4 – Table 2 Item specification Item Specification Lubricative System Press & splash Ignition System CDI Rated Power 10.5kW/6500(r/min) Fuse 15 A Max Torque 17.6N.m/5000(r/min) Front light 12V 35W/35W×2 Compression ratio 10.01 ∶ Tail/stop light 12V P21/5W Spark Plug Model DPR7EA(NGK) 、D7RTC或DPR6EA License light 12V 5W Spark plug gap mm 0.6~0.7 mm Turning light 12V 10W×4 Gap of valve 0.1(cold) Fuel RQ90 above Idling speed (1500±150)r/min Gearbox oil SAE 80W/90 Engine oil SF SAE 10W/40 capacity of gear box 0.18L Capacity of engine oil 1.1L

Incoming search terms:

2008 KTM Model Engine Oil Recommendation Chart

0

Filed Under (KTM) by admin on 24-11-2010

download
2008 Model Type Recommended Engine Oil Type Quantity SPORTMINICYCLES AC 50 SX MINI Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L SPORTMINICYCLES LC 50 SX JUNIOR Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L 50 SX Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L 65 SX Motorex Top Speed 4T 15W50 0.5L SX 2 STROKE 85 SX Motorex Top Speed 4T 15W50 0.5 L 105 SX Motorex Top Speed 4T 15W50 0.5 L 125 SX Motorex Top Speed 4T 15W50 0.7 L 144 SX Motorex Top Speed 4T 15W50 0.7 L 250 SX Motorex Top Speed 4T 15W50 0.7 L SX 4 STROKE 250 SX-F Motorex Power Synt 4T 10W50 1.1 L 450 SX-F Motorex Power Synt 4T 10W50 1.35 L 505 SX-F Motorex Power Synt 4T 10W50 1.35 L CROSS COUNTRY 2 STROKE 65 XC Motorex Top Speed 4T 15W50 0.5L 85 XC Motorex Top Speed 4T 15W50 0.5L 105 XC Motorex Top Speed 4T 15W50 0.5 L 200 XC Motorex Top Speed 4T 15W50 0.7 L
200 XC-W Motorex Top Speed 4T 15W50 0.7 L 250 XC Motorex Top Speed 4T 15W50 0.7 L 250 XC-W (e) Motorex Top Speed 4T 15W50 0.7 L 300 XC Motorex Top Speed 4T 15W50 0.7 L 300 XC-W (e) Motorex Top Speed 4T 15W50 0.7 L CROSS COUNTRY 4 STROKE 250 XC-F Motorex Power Synt 4T 10W50 1.1 L 250 XC-F-W Motorex Power Synt 4T 10W50 1.1 L 450 XC-F Motorex Power Synt 4T 10W50 1.35 L 450 XC-W (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L 505 XC-F Motorex Power Synt 4T 10W50 1.35 L 530 XC-W (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L ENDURO RACING 450 EXC (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L 530 EXC (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L SUPERMOTO LC4 690 Supermoto Motorex Power Synt 4T 10W60 Approx. 2.0 L SPORT ATV 450 XC Motorex Power Synt 4T 10W50 2.0 L 525 XC Motorex Power Synt 4T 10W50 2.0 L LC8 950 Super Enduro (R) Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Adventure Orange Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Adventure Black Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Adventure S Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Super Duke Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Super Duke R Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L

Incoming search terms:

Sanyang JET 50/100 and JET Euro 50/100 Specifications And Service Manual

0

Filed Under (Sym) by admin on 24-11-2010

download
Carbon monoxide If you must run your engine, ensure the place is well ventilated. Never run your engine in a closed area. Run your engine in an open area, if you have to run your engine in a closed area, be sure to use an extractor. Caution Exhaust contains toxic gas which may cause one to lose consciousness and even result in death. Gasoline Gasoline is a low ignition point and explosive material. Work in a well-ventilated place, no flame or spark should be allowed in the work place or where gasoline is being stored. Caution Gasoline is highly flammable, and may explode under some conditions, keep it away from children. Used engine oil Caution Prolonged contact with used engine oil (or transmission oil) may cause skin cancer although it might not be verified. We recommend that you wash your hands with soap and water right after contacting. Keep the used oil beyond reach of children. Hot components Caution Components of the engine and exhaust system can become extremely hot after engine running. They remain very hot even after the engine has been stopped for some time. When performing service work on these parts, wear insulated gloves and wait until cooling off. Battery Caution y Battery emits explosive gases; flame is strictly prohibited. Keep the place well ventilated when charging the battery. y Battery contains sulfuric acid (electrolyte) which can cause serious burns so be careful do not be spray on your eyes or skin. If you get battery acid on your skin, flush it off immediately with water. If you get battery acid in your eyes, flush it off immediately with water and then go to hospital to see an ophthalmologist. y If you swallow it by mistake, drink a lot of water or milk, and take some laxative such as castor oil or vegetable oil and then go to see a doctor. y Keep electrolyte beyond reach of children. Brake shoe Do not use an air hose or a dry brush to clean components of the brake system, use a vacuum cleaner or the equivalent to avoid dust flying. Caution Inhaling dust may cause disorders and cancer of the breathing system. Brake fluid Caution Spilling brake fluid on painted, plastic, or rubber parts may cause damage to the parts. Place a clean towel on the above-mentioned parts for protection when servicing the brake system. Keep the brake fluid beyond reach of children

Incoming search terms:

2004 Honda CRF450R OWNER'S MANUAL

0

Filed Under (Honda) by admin on 21-11-2010

download
motorcycle can be kickstarted with the transmission in gear by disengaging the clutch before operating the kickstarter. Check the engine oil, transmission oil and coolant levels before starting the engine (page 21, 23, 24). Cold Engine Starting: 1. Turn the fuel valve ON. 2. Shift the transmission into neutral. 3. If the temperature is 35°C (95°F) or below, pull the choke knob fully out. 4. If the temperature is below 0°C (32°F), open the throttle two or three times. (The engine requires a richer mixture for starting in cold weather. When the throttle is so opened, the accelerator pump will feed extra fuel to the cylinder, thereby facilitating starting in cold weather.) 5. With the throttle closed, operate the kickstarter starting from the top of the kickstarter stroke, kick through to the bottom with a rapid, continuous motion. (Do not open the throttle, As the carburetor is equipped with an accelerator pump, excessive fuel will be charged into the engine, and the spark plug will be fouled if the throttle is opened and closed repeatedly. Excessive fuel in the engine makes kick- starting difficult.) 6. About a minute after the engine starts, push the choke knob back all the way to fully OFF. If idling is unstable, open the throttle slightly. (1) FUEL FILL CAP (2) BREATHER TUBE WARNING (1) FUEL VALVE (2) CHOKE KNOB Warm Engine Starting: 1. Turn the fuel valve ON. 2. Shift the transmission into neutral. 3. Pull the hot start lever and kick-start the engine. (Do not open the throttle.) 4. As soon as the engine starts, release the hot start lever 1. Shift the transmission into neutral. 2. Pull the hot start lever and kick-start the engine. (Do not open the throttle.) 3. As soon as the engine starts, release the hot start lever. Starting the engine excessively charged with fuel by throttle blipping or other reasons: 1. Shift the transmission into neutral. 2. With the throttle fully opened, repeat kickstarter operation approximately 10 times very slowly to discharge excessive fuel from the engine. 3. Pull the hot start lever and kick-start the engine (Do not open the throttle.) 4. As soon as the engine starts, release the hot start lever. Stopping The Engine 1. Shift the transmission into neutral. 2. Turn the fuel valve OFF. 3. Lightly open the throttle 2 – 3 times, and then close it. 4. Depress and hold the engine stop button until the engine stops completely. NOTE: • Failure to close the fuel valve may cause the carburetor to overflow. (1) THROTTLE GRIP (2) ENGINE STOP BUTTON Break-In Procedure Help assure your CRF’s future reliability and performance by paying extra attention to how you ride during the first operating day or 15 miles (25 km). During this period, avoid full-throttle starts and rapid acceleration. This same procedure should be followed each time when: • Piston is replaced • Rings are replaced • Cylinder is replaced • Crankshaft or crank bearing are replaced

Incoming search terms: