Harley Davidson Power Pod Switch Housing Throttle Bracket Installation Instructions

0

Filed Under (Harley Davidson) by admin on 19-03-2012

download
Attach the “Y” bracket to the Power Pod by using the two Power Pod socket head screws that come in your parts kit. (This bracket may already be attached from the factory. ) 2) Remove the two screws on the Right Hand switch housing on your Harley Davidson motorcycle and reinstall them through the two “Y” bracket open holes and back into the switch housing holes. Tighten snugly. In this mounting position, the heads of the two socket head screws holding the “Y” bracket to the Power Pod should be touching the handlebar; this is necessary as it grounds the unit for proper operation. If the unit is not grounded properly, it will not operate. 3) Run the Power Pod’s 60″ power cord to your battery. Make sure as you hide the cord on the way to the battery, that your handlebars turn freely and that the cord does not come in contact with hot engine parts that may melt the wire over time. 4) At some point, before reaching the battery, attach (using the two butt connectors) the in-line fuse holder. TIP: Keeping the in-line fuse holder in an easy to access place (like under a side panel etc) rather than under the seat, may help you service the fuse easier in case of a blown fuse. In most cases, it’s easier to pull a side panel off than it is to remove a seat! 5) Attach the Power Pod lead wire (with in-line fuse now already attached) directly to the battery for power at anytime without using the key. The hot lead can also be run to the fuse box which will require using the ignition switch to “Accessory” or “ON” in some cases. TIP : Always use the in-line fuse for safety. 6) Insert the 20 amp fuse into the in-line fuse holder. Strap down with zip-ties any loose wires and you’re done!

Incoming search terms:

YAMAHA Installing the Motorcycle Enhancements Remote Oil Filter

0

Filed Under (Yamaha) by admin on 17-01-2012

download
In order to install the new Remote Oil Filter Kit, you’ll need to remove the stock Yamaha “beauty cover” and the old filter and filter cover. Remove the engine parts necessary to access the stock filter as outlined in the V-Star owner’s manual. The parts should come off in this order: 1. Muffler assembly 2. Front exhaust pipe 3. Rear brake reservoir cover bolt and brake cover (the reservoir should not be removed, it can remain in place and be moved aside as needed) 4. Right floorboard (this can be simply loosened, by loosening the two bolts underneath) With the above parts removed, you can remove the Allen bolts holding the beauty cover and filter cap from your engine. There are five Allen bolts holding the beauty cover (so named, because most of the cover just covers the chromed side of the engine
There are five bolts holding the cover. Ignore the three on the “Yamaha” cap in the middle – these just hold the Yamaha cap to the beauty cover itself. One bolt is hidd – in this picture – just be the Yamaha ca en low p

Corolla & Matrix 2005 – 2006 1ZZ-FE ENGINE NO START OR EXTENDED CRANK CONDITION

0

Filed Under (Toyota Manuals) by admin on 29-05-2011

Download
Some 2005 and 2006 model year Corolla and Matrix vehicles equipped with a 1ZZ–FE engine may exhibit a “no start” or “extended crank” condition. This may be caused by insufficient fuel pressure after the vehicle has been parked for a period of time. The fuel pump assembly manufacturing process has been improved to correct this condition. Applicable Vehicles S 2005 – 2006 model year Corolla and Matrix (2WD) vehicles equipped with the
1ZZ–FE engine. Parts Information PREVIOUS PART NUMBER 77020–02180 77144–04010 77169–02050 CURRENT PART NUMBER Same Same Same PART NAME Fuel Suction w/Pump & Gauge Tube Assembly Fuel Pump Gauge etainer
Fuel Suction Tube Set Gasket

Incoming search terms:

Toyota Yaris 2006 up models 5 speed and Automatic Instruction Manual

0

Filed Under (Toyota Manuals) by admin on 23-05-2011

Download
Using the ⑥ bolt (1) and #15 bracket spacer B (1), attach #5 alternator bracket as shown in illustration. Install the alternator upside down. Using the ⑧ head bolt (1) and washer (1), attach alternator to #5 Alternator Bracket.
6. Using ⑱ bolt (1) and ⑬ nut (1), attach the alternator on bottom alternator mount (lowest hole on Bracket A).
7. After installing alternator, make sure the A/C line does not interfere with belts. If it does, push the A/C line forward and make sure the alternator has enough clearance. ⑧Bolt Washer 8. Some models will have addition A/C lines near engine mount (not shown here). Please adjust A/C line to clear alternator pulley. Please find a suitable spot where the A/C line will not interfere with the pulleys and tie theline down with zip ties

Incoming search terms:

YAMAHA VMX12W1 (C) OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 25-11-2010

download
Brake pedal The brake pedal is on the right side of the motorcycle. To apply the rear brake, press down on the brake pedal. EAU13060 Fuel tank cap To remove the fuel tank cap 1. Push the levers on the left and right side of the rider seat backrest as shown and slide the rider seat backrest forward. 2. Insert the key into the lock, and then turn it 1/4 turn clockwise. The lock will be released and the fuel tank cap can be removed. To install the fuel tank cap 1. Insert the fuel tank cap into the tank opening with the key inserted in the lock and with the mark on the cap facing forward. 2. Turn the key counterclockwise to the original position, and then remove it. 3. Slide the rider seat backrest rearward and push it down. NOTE: The fuel tank cap cannot be installed 1. Brake pedal 1. Opening lever 1. Unlock.
INSTRUMENT AND CONTROL FUNCTIONS 3-7 2 3 4 5 6 7 8 9 unless the key is in the lock. In addition, the key cannot be removed if the cap is not properly installed and locked. WARNING EWA10130 Make sure that the fuel tank cap is properly installed before riding. EAU13211 Fuel Make sure that there is sufficient fuel in the tank. Fill the fuel tank to the bottom of the filler tube as shown. WARNING EWA10880 * Do not overfill the fuel tank, otherwise it may overflow when the fuel warms up and expands. * Avoid spilling fuel on the hot en- gine. CAUTION: ECA10070 Immediately wipe off spilled fuel with a clean, dry, soft cloth, since fuel may deteriorate painted surfaces or plastic parts. EAU13300 CAUTION: ECA11400 Use only unleaded gasoline. The use of leaded gasoline will cause severe damage to internal engine parts, such as the valves and piston rings, as well as to the exhaust system. Your Yamaha engine has been designed to use regular unleaded gasoline with a pump octane number [(R+M)/2] of 86 or higher, or a research octane number of 91 or higher. If knocking (or pinging) occurs, use a gasoline of a different brand or premium unleaded fuel. Use of unleaded fuel will extend spark plug life and reduc

YAMAHA YZF-R125 SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 25-11-2010

download
Fuel tank cap To remove the fuel tank cap 1. Open the fuel tank cap lock cover. 2. Insert the key into the lock and turn it 1/4 turn counterclockwise. The lock will be released and the fuel tank cap can be removed. To install the fuel tank cap 1. Push the fuel tank cap into position with the key inserted in the lock. 2. Turn the key clockwise to the original position, and then remove it. 3. Close the lock cover. NOTE: The fuel tank cap cannot be installed unless the key is in the lock. In addition, the key cannot be removed if the cap is not properly installed and locked. WARNING EWA11140 Make sure that the fuel tank cap is properly installed before riding. EAU13211 Fuel Make sure that there is sufficient fuel in the tank. Fill the fuel tank to the bottom of the filler tube as shown. WARNING EWA10880 Do not overfill the fuel tank, otherwise it may overflow when the fuel warms up and expands. Avoid spilling fuel on the hot en- gine. 1. Fuel tank cap lock cover 2. Unlock. 1. Fuel tank filler tube 2. Fuel level
INSTRUMENT AND CONTROL FUNCTIONS 3-8 3 CAUTION: ECA10070 Immediately wipe off spilled fuel with a clean, dry, soft cloth, since fuel may deteriorate painted surfaces or plastic parts. EAU43420 CAUTION: ECA11400 Use only unleaded gasoline. The use of leaded gasoline will cause severe damage to internal engine parts, such as the valves and piston rings, as well as to the exhaust system. Your Yamaha engine has been designed to use premium unleaded gasoline with a research octane number of 95 or higher. If knocking (or pinging) occurs, use a gasoline of a different brand. Use of unleaded fuel will extend spark plug life and reduce maintenance costs. EAU13442 Catalytic converters This vehicle is equipped with catalytic converters in the exhaust system. WARNING EWA10860 The exhaust system is hot after operation. Make sure that the exhaust system has cooled down before doing any maintenance work. CAUTION: ECA10700 The following precautions must be observed to prevent a fire hazard or other damages. Use only unleaded gasoline. The use of leaded gasoline will cause unrepairable damage to the catalytic converter. Never park the vehicle near possible fire hazards such as grass or other materials that easily burn. Do not allow the engine to idle too long.

YAMAHA V-Star 1100 Motorcycle Enhancements Remote Oil Filter Installation Manual

0

Filed Under (Yamaha) by admin on 10-11-2010

download
Removing Your Old Filter and Beauty Cover In order to install the new Remote Oil Filter Kit, you’ll need to remove the stock Yamaha “beauty cover” and the old filter and filter cover. Remove the engine parts necessary to access the stock filter as outlined in the V-Star owner’s manual. The parts should come off in this order: 1. Muffler assembly 2. Front exhaust pipe 3. Rear brake reservoir cover bolt and brake cover (the reservoir should not be removed, it can remain in place and be moved aside as needed) 4. Right floorboard (this can be simply loosened, by loosening the two bolts underneath) With the above parts removed, you can remove the Allen bolts holding the beauty cover and filter cap from your engine. There are five Allen bolts holding the beauty cover (so named, because most of the cover just covers the chromed side of the engine There are five bolts holding the cover. Ignore the three on the “Yamaha” cap in the middle – these just hold the Yamaha cap to the beauty cover itself. One bolt is hidd – in this picture – just be the Yamaha ca en low p. The bottommost bolt on the beauty cover will likely leak some oil when you remove it – it holds on the inner oil filter cover. Once you remove the beauty cover, you can remove the oil filter cover, and the oil filter Keep these two “O” rings, you’ll need them for the remote kit Old oil filter. Toss it away; you’ll never need one again! Throw away the old filter, and carefully remove the orange and black “O” rings from the filter cover (see picture above). These two “O” rings will go on the new engine cap in the same order as on the old filter cover. “O” ring for bottom bolt. When the beauty cover and filter cover are removed, be sure not to lose the tiny “O” ring that the bottom bolt goes through. Preparing the Remote Oil Filter Kit Remove the orange and black “O” rings from the stock filter cover plate, and place them on the Remote Oil Filter Kit engine cap – black on the inside, orange on the outside – just like on the stock filter cover.

Incoming search terms:

Incoming search terms: