HARLEY DAVIDSON HIGH OUTPUT ALTERNATOR INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
this kit is designed for use on 1980 and later FLT and FLTC models, 1982 and later FXR, FXRS, and FXRT models and 1984 and later FXRD, FLHT, FLHTC, FXRDG, FXRS-SP, FXLR, FLHS and FXRC model vehicles. This kit contains the following parts: QTY DESCRIPTION 4 Screw, sockethead torx 1 Ring terminal 6 Cable strap 1 Rotor assembly 1 Spacer, thick 1 Spacer, thin 1 Stator assembly 1 Regulator Installation 1. Refer to applicable Service Manual for detailed removal and installation procedures. 1 CAUTION Disconnect battery (negative cable first) before performing any electrical system servicing. 2. Observe the following guidelines to ensure proper operation. A. Do not drop or pound on the new rotor assembly. Permanent damage can result. B. Do not install a new style rotor with an old style rectifier. Permanent rectifier damage can result. C. Do not install a new style rectifier with an old style rotor. Permanent rectifier damage can result. D. Route the black rectifier wire away from hot or moving parts. Secure it to the frame with cable straps. Trim excess wire length, crimp on ring terminal and attach to positive battery terminal. 3. See Figure 1. When installing rotor and stator use thin spacer inside and thick spacer outside of rotor

1999-2002 Indian Motorcycle Mirror Housing Removal and Replacement

0

Filed Under (Indian) by admin on 31-10-2010

download
1. Remove seat. 2. Disconnect battery. 3. Remove handlebar cover on top-center of handlebar. 4. Remove left-side clutch-bracket assembly. This exposes an access hole on the underside of the handlebar. 5. Pass the end of the Signal® mirror wires through one of the small holes located on the underside of the clutch-bracket assembly housing. 6. Take piano wire/fish tape and insert at the access hole located on the underside of the handlebar to the center of the handlebar (center handlebar cover removed). 7. Fasten the end of the Signal® mirror wires to the piano wire/fish tape and pull through the handlebars to the center opening. 8. Pull excess wire through the handlebars leaving approximately 2″ of extra wire at the mirror side. 9. Re-assemble clutch-bracket assembly allowing the Signal® mirror wire to wrap around the outside edge of the cover assembly into the underside access hole. Secure Signal® mirror with enclosed 1.5″ long 5/ 16 ” – 24 Allen head bolt. 10. Loosen throttle assembly side and slide back to expose access hole. DO NOT REMOVE THROTTLE ASSEMBLY. Proceed to pass the Signal® mirror wire through the handlebar at the opposite side and re-assemble the throttle assembly. 11. Run both sets of wires under the fuel tank along the topside of the frame to the battery compartment. 12. Connect both black wires to the enclosed ring connector for connection to the battery ground terminal. 13. Locate the male/female electrical connector that is located behind the battery. This wiring assembly is for your tail lamp assembly for braking and turning (see photo). 14. Make sure the harnesses are routed securely to the wire connectors and enough slack is left for splicing or soldering. Cut the heat shrink into (4) equal pieces (approx. 2″ each). 15. Slide the heat shrink over the passenger side Signal® mirror wire. Solder the Right Signal® mirror wire to the Brown wire. Slide the heat shrink over to cover the soldered area. Heat the shrink tube into place with a heat shrink gun or hair dryer. 16. Repeat sliding the heat shrink over the driver side Signal® mirror wire. Solder the Left Signal® mirror wire to the Purple wire. Slide the heat shrink over to cover the soldered area. Heat the shrink tube into place with a heat shrink gun or hair dryer. 17. Connect ground and positive battery connections. 18. Re-install seat.

Incoming search terms: