Yamaha 1998-2001 YZF-R1 Installation Instructions (Slip on system)

0

Filed Under (Yamaha) by admin on 16-02-2012

download
Remove the lower fairing. 2. Remove the existing exhaust system from the EXUP valve rearward (EXUP valve is retained). Save the stock exhaust clamp for reuse. 3. Inspect the exhaust gasket. Replace if necessary. 4. Install the S-Bend to the rear of the EXUP valve, make sure the system fits flush. Reuse the stock exhaust clamp to connect the S-bend to the valve. 5. Install the TiForce end can to the S-bend tail pipe. 6. Loosely attach the two rubber bands, stainless steel bands (K), and stay to the end can using the supplied 6mm hardware (H) and the hanger / stay arm (G). (See figure 1) . 7. Place the bands approximately 180mm from the edge of the end can. (See figure 2) . 8. Using the stock provided mounting point on the passenger foot peg, use the M10x45mm bolt and hardware to mount the end can loosely, allowing for some adjustment. 9. Carefully align the two stainless bands so that they are parallel to each other, and spaced properly on the can. Tighten the 6mm hardware (H). Make sure that the rubber pads fully cover the bands (K). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. 10. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire exhaust system to remove any residual oils, anti seize, fingerprints and dirt prior to starting the motor. FAILURE TO CLEAN THE TUBING AND CAN MAY RESULT IN PERMANENT STAINING OF THE SYSTEM WHEN HEATED. 11. Attach the supplied springs to secure the end can to the S-bend pipe. Make sure the exhaust system is free and clear of the bike. If necessary, adjust for proper clearance. 12. Go back and tighten all fasteners. 13. Check that all fasteners are tightened per specifications, then start the motor and check for exhaust leaks. 14. Reinstall the fairing lowers.

Yamaha YZF-R1 and R6 TiForce slip on exhaust system REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 09-01-2012

download
1. Remove the fairing lowers. 2. For R1 owners, please remove the existing exhaust system from the EXUP valve rearward (EXUP valve is retained) and set aside. Save the stock exhaust clamp for reuse. For R6 owners, please disconnect the stock S-bend from the rear of the collector and set aside. Save the stock exhaust clamp for reuse (new clamp provided). Save the stock end can mounting bolt for reuse as well. 3. R1 owners only -Inspect the exhaust gasket. Replace if necessary (gasket provided). 4. For R1 owners -Install the S-Bend to the rear of the EXUP valve, make sure the system fits flush. Reuse the stock exhaust clamp to connect the S-bend to the valve. For R6 owners -Install the TiForce S-bend to the rear of the stock head pipes and collector. Make sure the system fits flush and snug. Reuse the stock exhaust clamp or the provided clamp and loosely attach for now. 5. Install the TiForce end can to the S-bend tail pipe. 6. Loosely attach the two rubber bands, stainless steel bands (K), and stay to the end can using the supplied 6mm hardware (H) and the hanger / stay arm (G). See figure 1 for the assembly procedure. 7. R1 owners -Place the bands approximately 180mm from the edge of the end can. See figure 2. R6 owners -Place the bands approximately 195mm from the edge of the end can. See figure 2. 8. R1 owners -Using the stock provided mounting point on the passenger footpeg, use the M10x45mm bolt and hardware to mount the end can loosely, allowing for some adjustment. 9. Carefully align the two stainless bands so that theyare parallel to each other, and spaced properly on the can. Tighten the 6mm hardware (H). Make sure that the rubber pads fully cover the bands (K). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. 10. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire TiForce exhaust system to remove any residual oils, anti seize, fingerprints and dirt prior to starting the motor. FAILURE TO CLEAN THE TUBING AND CAN MAY RESULT IN PERMANENT STAINING OF THE SYSTEM WHEN HEATED. 11. Attach the supplied springs to secure the end can to the S-bend pipe using a spring installation tool if available. Make sure the exhaust system is free and clear of the bike. If necessary, adjust for proper clearance. 12. Go back and tighten all fasteners. 13. Check that all fasteners are tightened per specifications, then start the motor and check for exhaust leaks. 14. Reinstall the fairing lowers.

Incoming search terms:

2008-2009 HONDA CBR 1000 RR DUAL CANISTER SLIP-ON INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 22-11-2011

download
INSURE THE EXHAUST SYSTEM AND EXHAUST COMPONENTS ARE FULLY COOLED. 2. INSURE THE MOTORCYCLE IS STABLE ON KICKSTAND OR REAR CENTERSTAND OR SERVICE TABLE. 3. REMOVE THE 3 PLASTIC BUTTONS HOLDING THE PLASTIC COVER OVER THE EXHAUST SERVO. (THIS IS LOCATED DIRECTLY INSIDE THE RIGHT REAR PASSENGER PEG BRACKET) DETACH THE CABLE END FROM THE SERVOnWHEEL AND REMOVE THE ENTIRE CABLE FROM THE RETAINING CLIP. THE ENTIREnCABLE WILL NOW REMOVE WITH THE REST OF THE EXHAUST.REPLACE THE PLASTIC COVER FOR THE SERVO AND REINSTALL THE 3 PLASTIC BUTTONS. 6. REMOVE THE STOCK MUFFLER MOUNTING BOLT. REMOVE 7. REMOVE THE STOCK EXHAUST CLAMP. (IT IS NOT UNCOMMON FOR THE CLAMP BOLT TO BREAK DURING REMOVAL.)b8. REMOVE THE ENTIRE STOCK EXHAUST ASSEMBLY. BE CAREFUL NOT TO SCRATCH THE SWING ARM DURING REMOVAL. 9. REMOVE THE STOCK EXHAUST GASKET FROM HEADER PIPE IF IT DID NOT COME OFF WITH THE STOCK EXHAUST. THIS GASKET WILL
NOT BE USED. 10. PREASSEMBLE THE HYPERFLO EXHAUST BEFORE INSTALLING. HYPERFLO RECOMMENDS YOU DO THIS PORTION ON CARPET OR A CLEAN PADDED AREA. YOU MAY ALSO USE THE PLASTIC BUBBLE PACKAGING AS A PAD TO PROTECT THE CANISTERS DURING PREASSEMBLY. 11. PREASSEMBLE THE LARGE DIAMETER CAN TO THE S-PIPE FIRST. INSTALL THE SPRING ON THE CANISTER FIRST AND PULL AWAY FROM THE CANISTER TO INSURE YOU DO NOT SCRATCH THE CANISTER

2005-2009 ROYAL STAR TOUR DELUXE & 1999-2010 VENTURE OVAL BAG SLASH SLIP-ON MUFFLER SET INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 09-11-2010

download
1. Loosen the bolt on the front clamp securing the muffler to the headpipe. Important: Do not unbolt the OEM headpipes. 2. Loosen and remove the bolt from the muffler hanger located beneath the saddlebag. 3. Pull the muffler off the headpipe. It may be necessary to rotate the muffler and wiggle it a bit to free it. 4. Place a new exhaust clamp on the front of your new Oval Slash pipe. 5. Slide the new exhaust over the headpipe by rotating it and pushing it forward at the same time. 6. Align the hole in the mounting bracket and reinsert the OEM rear mounting bolt with the supplied nut and lock washer. Finger tighten only at this point of the installation. 7. After the brackets are in place, securely tighten all exhaust pipe clamps and brackets. 8. Reinstall the saddlebag. 9. Repeat Step #1 through Step #9 for the other side of the motorcycle. 10. For optimum performance we recommend the carburetors air/fuel mixtures be adjusted for the change in exhaust flow and back pressure. For best results, this procedure should be performed by a qualified Yamaha service technician. 11. Tighten all bolts/nuts after riding 100 miles, including baffle retaining screws