2004 KTM 250 EXC-R exhaust system INSTALLATION

0

Filed Under (KTM) by admin on 07-02-2012

download
1. Remove the rear shock and the standard exhaust pipe. And attach the rear shock again. (Standard exhaust flange should remain the current position) 2. Lightly attach the front exhaust pipe to the engine. (See Photo. 2) 3. Insert the joint and tail pipe to lightly attached front exhaust pipe in step 2. Shake the whole for the better fitting. Then, attach the supplied springs to the joint. Lightly attach this tail pipe with the standard bolt. *Insert the two inner collars to the joint. 4. Lightly assemble the silencer and the silencer stay. Insert this to the tail pipe. Lightly attach this tail pipe to the standard attachment position with supplied bolt and collar. Check the best position for the silencer band. (See Photo. 3) 5. Remove the silencer attached in step 4. Securely fasten the bolt of the silencer band. Insert this silencer to the tail pipe and lightly fasten the bolt of the stay. 6. Securely attach the tail pie followed by the silencer stay. 7. Attach supplied springs to the joint of the silencer. 8. Clean all surfaces. Remove any oil on the exhaust pipe and silencer. 9. Make sure all bolts and nuts are securely fastened. Run the engine and ensure there are no exhaust gas leaks. (See Photo. 4) *Carburetor adjustment will be required in the weather and course

YAMAHA VIRAGO 700/ 1100 2 into 2 EXHAUST SYSTEM REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 20-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the slip joint clamp on the front and rear head pipe, which are located at the muffler box. 2. Remove the two nuts that hold the front head pipe to the engine. Slip the head pipe out of the muffler box and set it aside. Note: Do not remove the rear head pipe, it has been incorporated in the design of the new exhaust system. 3. Remove the muffler box mounting bolt located in front of the passenger foot rest on the left side. 4. Remove two bolts from the right passenger foot rest assembly and set the foot rest aside. 5. Slide the muffler box off of the rear head pipe and set it aside. 6. Replace the muffler box mounting bolt (from step #3) using the washer and nut (supplied) on the back side. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Attach the mounting bar to the motorcycle frame behind the right passenger foot rest. Align the two holes in the largest bracket on the mounting bar with the two holes on the frame, be sure the bend in the mounting bar is pointing to the center of the motorcycle. 2. Install the round steel spacer (supplied) to the rear most hole in the bracket. 3. Attach the foot rest using the two 8mm x 1.25 x 25mm bolts (supplied). 4. Slide the new exhaust flange (supplied) onto the front head pipe. 5. Install the two heat shields to the front head pipe using the four hose clamps (supplied). Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Place the heat shields onto the front head pipe. Note: Be sure the bend in the heat shield matches the bend in the head pipe exactly. Wrap the hose clamp around the head pipe and give the screw three to four turns, leaving heat shield loose on the head pipe. Repeat this step with the heat shield on the rear head pipe. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 6. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 7. Slide a chrome pinch clamp (supplied) onto the expanded end of the new rear head pipe. Install a 3/8″ x 1″ bolt with a flat washer on either side of the clamp followed by a lock nut (hardware supplied). Repeat this step on the inlet end of each muffler using the two muffler clamps with 5/16″ x 1 1/4″ bolts (hardware supplied) but leave the clamp loose at this time. 8. Slip the new rear head pipe with the heat shield attached, over the stock rear pipe and gasket, but leave the clamp loose at this time. 9. Install the front head pipe, with the heat shield attached and stock gasket in place, to the front cylinder using the stock nuts, leave them loose at this time

Incoming search terms:

BUELL BLAST SS2-R Exhaust System Removal And Installation

0

Filed Under (Tips and Review) by admin on 18-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the two nuts that mount the header to the cylinder head. 2. Remove the rear muffler mounting bolts. Remove the bolt from the insulated mount at the front of the muffler. Save the nuts and bolts for reuse. 3. Remove the stock head pipe and muffler assembly. 4. Using circlip pliers carefully remove the circlip and flange from the stock exhaust system.Save for reuse. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Slide the circlip and flange over the VHR head pipe. NOTE: If the circlip looks bent or twisted replace it with a new circlip. 2. Slide the supplied clamp over the head pipe. 3. Install the head pipe into the exhaust port using the stock flange nuts. Leave finger tight at this time. 4. Bolt the head pipe clamp to the engine using the supplied bracket stamped #311. Refer to Fig. 1for the assembly order of the front mounting hardware. Leave loose at this time. 5. Slide the supplied clamp onto the notched end of the muffler assembly. 6. Slip the muffler assembly onto the head pipe. Bolt the muffler assembly to the original mounting points at the rear of the frame, using the supplied 5/16″-18×3/4″ socket head capscrews, stock nuts and washers. 7. Tighten the exhaust flange nuts and muffler clamp. 8. Tighten the two bolts that mount the muffler assembly to the motorcycle. 9. Be sure to tighten all hardware before starting your motorcycle. RE-JETTING INSTRUCTIONS Re-jetting the carburetor will result in realizing the “full” potential of this performance exhaust system. Vance & Hines offers jet kits for most applications

Incoming search terms:

PIAGGIO Power Program with SIP Stainless Steel Joint Pipe Installation Manual

0

Filed Under (Piaggio) by admin on 28-10-2010

download
First, loosen and remove both screws between joint pipe and exhaust. Then, remove the other two upper screws, as in illustration 2, between cylinder and joint pipe. This may be a little difficult to reach. For additional ease removing screws, raise up motor frame with a crowbar or chisel. Now, remove old joint pipe and replace with SIP stainless steel pipe. Don’t forget to replace old gaskets with new gaskets, included in delivery. Join us in the SIP Article Forum for further handy tips and tricks from those in the know at www.sip-scootershop.com Turn down screws bit by bit, one after another, to ensure balanced fit, making sure to loosen muffler screws shortly. If you should have difficulty getting a good fit, here’s a tip: drill longer holes on exhaust flange to get better adjustment. Finito; put away the tools and take a test drive

Kawasaki ZRX-1100 / 1200 exhaust system Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the existing exhaust system and save the flange nuts for reuse. Save the stock exhaust can mounting bolt and nut for reuse as well. 2. Inspect the exhaust gaskets. Replace if necessary. 3. Attach the head pipes 1, 2, 3 , and 4 to the exhaust ports of their respective cylinders, using the flange nuts saved from step 1 above. Loosely apply the flange nuts for now, allowing for ome adjustment. 4. Attach the Y-pipe collectors to the head pipes. Please note that one collector goes to pipes #1 and #4 and one collector goes to pipes #2 and #3 (collectors are labeled). Make sure the ends of the head pipes fit flush and snug in the ports. Do not install the springs at this time. 5. Install the S-Bend to the rear of the two Y-pipe collectors. Do not install the springs at this time. 6. Go back and retighten the head pipe flange nuts per factory specifications – make sure the head pipes are centered in each port. 7. Slide the TiForce end can into place on the S-bend pipe. 8. Loosely attach the two rubber bands, stainless steel bands K, and the stay / hanger G, to the end can using the supplied 6mm hardware H. (See figure 1) . Make sure that the rubber bands fully cover the stainless bands to prevent scratches to the can. 9. Place the bands approximately 108mm from the edge of the end can. (See figure 2) . 10. Go back and tighten the exhaust flange nuts per factory specification. Do not over tighten. 11. Using the stock provided mounting point on the right passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 12. Attach the supplied springs to all the joints, starting from the head pipes and working back to the end can. 13. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance. 14. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can (refer to step 11 / figure 2), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure that the rubber pads fully cover the band(s). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. 15. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire exhaust system to remove any residual oils, anti seize, fingerprints and dirt prior to starting the motor. FAILURE TO CLEAN THE TUBING AND CAN MAY RESULT IN PERMANENT STAINING OF THE SYSTEM WHEN HEATED. 16. Check that all hardware is properly tightened, and then start the motor and check for exhaust leaks

Incoming search terms: