Suzuki M- 109 Front Head Pipe Installation Manuals

0

Filed Under (Suzuki) by admin on 18-02-2012

download
1. Remove seat (Fig 1) remove right side (Fig 2) panel with allen 6mm bolt and push-pin snap. (Fig 3) Figure 1 Figure 2 Figure 3
- 3 – 2. Remove 6mm bolt on heat shield and remove heat shield. (Fig 4) Figure 4 3. Remove two 8mm bolts on top muffler and remove two 8mm stock bolts on bottom muffler and remove mufflers. (Fig.5 & 6) Figure 5 Figure 6 4. Remove frame cover with stock allen 6mm bolt. (Fig 7) Figure 7 FFF – 4 – 5. Loosen brake pedal bolts to allow more room to remove the exhaust. (Fig 8) Figure 8 6. Remove exhaust system by removing stock 8mm bolts on exhaust flanges. (Fig 9) Figure 9 7. Unplug EXCVA wire connectors. (Fig 10) Figure 10 – 5 – 8. Remove three 8mm stock mufflers mounting brackets bolts as shown. (Fig 11) Figure 11 ffff 9. Remove EXCVA unit from the stock muffler bracket. (Fig 12) Figure 12 10. Remove the stock pulley from the EXCVA actuator unit as shown. (Fig 13)

Incoming search terms:

HARLEY DAVIDSON RONT & REAR HEADPIPE AND HEATSHIELDS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 10-11-2010

download
1. Remove both left and right saddlebags and set them aside. 2. Remove the right side floorboard from the frame and set aside. 3. Unplug the O 2 sensors on front and rear headpipes from motorcycle wire harnesses. 4. Remove the stock exhaust system. It may be necessary to lubricate the slip joints of the exhaust with WD-40 or similar lubricant to aid in disassembly. The stock muffler slide hangers may be left in place in the rubber mounts for later reinstallation of the mufflers. 5. Remove the stock rear headpipe support-mounting bracket by removing the two starter mounting bolts, this bracket will not be reused. Note: Use caution when removing the bolts so that any tools used do not come in contact with the positive post on the starter. Install the Cobra supplied, exhaust support-mounting bracket, see Figure 1. 6. Remove the stock exhaust flanges, retaining rings and O 2 sensors from the stock headpipes and headpipe support clamp from the front headpipe. Remove the new front headpipe from packaging and install the stock flange, retaining rings and O 2 sensor on to the pipe. 7. On the front headpipe slide the stock headpipe support clamp over it. Install the front headpipe on the motorcycle using the stock flange nuts to secure it to the exhaust port studs, but do not tighten at this time. Slide the headpipe support clamp forward on the headpipe and over the stock exhaust mount on the right side engine case, make sure the clamp’s rectangular hole is on top and the flat part of the clamp is downward, see Figure 2. Install the carriage bolt and nut to secure the tube clamp but do not tighten at this time. 8. Reinstall the muffler onto the front headpipe using one muffler slip clamp. Reinsert two stock 5/16- inch bolts into rear muffler mount, tighten to factory torque specs, do not tighten front muffler slip clamp at this time. (NOTE: On some models equipped with saddlebags the bag rail may need to be adjusted outward to allow proper clearance between muffler body and swing arm / axle nut.) 9. Tighten front headpipe flange nuts then headpipe support clamp to factory torque specifications. 10. Remove front heatshield and hose clamps from packaging. Unscrew the hose clamps and feed the tail end of the clamps through the clips on the inside of the heatshield from the bottom, so the screws are facing toward the bottom and accessible with a screw driver once the heatshield is installed. Install the heatshield over the front headpipe. (Hint: Spread the hose clamps apart slightly to make it easier to slide them over the muffler assembly and headpipes.) Align heatshield with headpipe and snug clamps but do not tighten .

SUZUKI M109 1800 cc EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 10-11-2010

download
1. Remove the seat and right side fairing cover (with M109 insignia), behind the fuel tank. To remove the fairing, release the plastic peg on top by pushing the center inward and pulling the fairing upwards until the peg releases, remove the M6 button head bolt at the bottom of the fairing. Pull the fairing outward from the rear and upward near the plastic peg to release it. Once it is free from all plastic pegs pull it forward to release it from the bottom of the fuel tank. 2. Remove the right side cover above the exhaust-mounting bracket secured by one M6 button head bolt, retain bolt for later. Remove the chrome steel cover above the exhaust secured by two remaining bolts, (this chrome piece will no longer be used.) Remove the large left rear rubber grommet and flanged steel collar from this chrome piece, to do this press the steel collar out of the rubber grommet first, once the collar is removed push the rubber grommet out of the wire loop on the chrome piece, set aside for later use. 3. Locate the exhaust valve actuator solenoid and harness and disconnect the black 3-prong electrical connector and white 2-prong electrical connector. 4. Remove the socket head bolts securing exhaust flanges to cylinder heads, set these fasteners aside for later use in reassembly. Support the weight of the exhaust system and remove the 2, 8 mm bolts and one 8 mm nut securing the exhaust mounting bracket and exhaust assembly. Keep these fasteners for use later. Remove the stock exhaust system as one complete unit; this includes the stock exhaust bracket, headpipes and muffler, exhaust valve solenoid and cables. 5. The exhaust valve actuator solenoid must now be removed from the stock exhaust-mounting bracket. To perform this, loosen the two nuts securing each cable to the exhaust valve cable-mounting tab, Position A in Figure 1. Make enough slack in the cables so that the ends of the cables’ threaded sheath may be disengaged from the end of the mounting tab. Now remove the two M6 hex head bolts securing the solenoid to the stock exhaust bracket. The stock exhaust mounting bracket, headpipes and muffler and exhaust valve solenoid cables will not be used anymore with the your new Cobra Exhaust System. 6. Remove the dust cover from the solenoid to expose the rotating cam and cables. DO NOT TRY TO ROTATE THE CAM RELATIVE TO THE ACTUATOR SELENOID TO REMOVE THE CABLES; DOING SO MAY DAMAGE THE INTERNAL COMPONENTS OF THE SOLENOID. To remove the cables from the cam, use the slack in the cables obtained in Step 5 to disengage the cable barrels from the cam, see Figure 1. THE DUST COVER WILL NOT BE REINSTALLED. 7. Now prepare the exhaust valve actuator solenoid for reuse. SECURELY HOLD THE CAM TO PREVENT IT FROM ROTATING IN THE SOLENOID. WHILE PREVENTING THE CAM FROM ROTATING, remove the 10 – 32 flange bolt securing it, see Figure 2. Replace the cam with the Cobra supplied cam, BE SURE TO PREVENT THE CAM FROM ROTATING WHEN REINSTALLING THE BOLT, OTHERWISE DAMAGE MAY OCCUR TO THE SOLENOID , see Figure 3. Torque to factory specifications.

Incoming search terms:

Incoming search terms: