HONDA 2005 CBR 600 RR FULL S/S EXHAUST HEADER INSTALLATION

0

Filed Under (Honda) by admin on 01-12-2011

download
Place the motorcycle in a vise or on it’s kick stand and make sure it is safe and secure. NOTE: If reusing the stock midpipe and muffler, skip ahead to step #5. 2) Remove the rider and passenger seats. Unplug the tail light, license plate light, and turn signals wires inside the tail section. 3) Remove the four bolts that secure the tail section to the subframe. Carefully remove the tail section from the subframe. 4) Remove the four bolts that secure the license plate/turn signal mount to the subframe. Remove the mount from the motorcycle. 5) Remove the upper and lower front fairing pieces. 6) Remove the two bolts that attach the right side footpeg assembly to the motorcycle. Disconnect the rear brake light switch and swing the footpeg assembly out of the way. Remove the outer plastic foot guard. Remove the aluminum heat shield from the motorcycle. 7) If equipped, remove the o2 sensor from the stock midpipe assembly.
NOTE: If reusing the stock midpipe and muffler, loosen the midpipe mounting bolts, and loosen the clamp securing the headpipe to midpipe connection. Skip ahead to step #9 8) Remove the midpipe mounting bolt, located on the right side of the subframe. Remove the
muffler mounting bolts. Lower the muffler and remove the rear exhaust section from the midpipe. 9) Remove the eight hex flange nuts securing the header flanges to the cylinder. 10)Remove the bottom header mounting bolt from the midpipe assembly. Remove the complete header from the motorcycle. 11)Remove the hat washer and rubber grommet from the stock midpipe assembly. Install the rubber grommet and hat washer into the hole provided on the Jardine midpipe assembly. 12)Slide the four headpipes into the new collectors. The headpipes are numbered from #1 thru #4, with #1 being the furthest toward the left side of the motorcycle, then work your way to the right. Do not install the provided springs at this time

Vespa PE/ PX Part Installation

0

Filed Under (Vespa) by admin on 28-10-2010

download
Section 2 – Engine Section 3 – Clutch Section 4 – Gearbox / Kickstart Section 5 – Gear Selector Section 6 – Rear Axle / Axle Bearing / Axle Seals / Gears Section 7 – Flywheel / Stator / Points / Condensor Section 8 – HT Coil Section 9 – Fuel / Oil Systems Section 10 – Starter Motor Section 11 – Rear Wheel / Rear Brake Section 12 – Exhaust Section 13 – Frame / Legshield Trim / Legshield Badges Section 14 – Centre Stand / Stand Feet Section 15 – Seat / Bag Hook Section 16 – Fuel / Oil Tank Section 17 – Horncover / Horncover Badges Section 18 – Side Panels / Panel Badges / Spare Wheel Cover Section 19 – Toolbox / Toolbox Lock Section 20 – Steering Bearings / Bearing Races / Steering Locks Section 21 – Forks / Fork Covers Section 22 – Front Suspension Section 23 – Rear Suspension Section 24 – Front Brake / Speedo Drive Section 25 – Floor Strips / Floor Rubber / End Caps Section 26 – Front Mudguard / Mudguard Crest / Flashes Section 27 – Front Hub / Front Hub Bearings / Hub Seals Section 28 – Hand Grips / Hand Levers / Gear Change Tube Section 29 – Handlebar / Speedometer Section 30 – Throttle Tube / Front Brake Switch / Master Cylinder Section 31 – Brake Pedal / Pedal Rubber Section 32 – Cable Set / Gear Cable Section 33 – Clutch Cable / Throttle Cable Section 34 – Speedo Cable / Choke Cable / Rear Brake Cable Section 35 – Wheel Rim / Rim Nut Section 36 – Headlight Section 37 – Taillight Section 38 – Light Switch / Rear brake Switch / Horn / Ign Switch Section 39 – Indicators / Indicator Switch / Flasher Unit Section 40 – Regulator / Battery Strap Section 41 – Wiring Loom Section 42 – Starter Relay

Incoming search terms: