Harley Davidson Softail 1987 to Current Trike Conversion Installation Manual

0

Filed Under (Harley Davidson) by admin on 05-03-2012

download
Protect yourself and others when you have a vehicle up in the air. Anytime you lift a vehicle, either by hoist or a jack, make sure that it is securely supported. b. c. d. e. f. Make sure the engine is turned off before you begin work. • Carbon Monoxide poisoning from exhaust gases: Be sure there is adequate ventilation whenever you run the engine. • Burns from hot parts: Let the engine and exhaust system cool before working on those areas. • Injury from moving parts: If running the engine, keep hands, fingers and clothing away from moving/rotating parts. Gasoline vapor and hydrogen gases from batteries are explosive. To reduce the possibility of fire or explosion, be careful when working near gasoline and batteries. Use only nonflammable solvent, not gasoline, to clean parts Never drain or store gasoline in an open container. Keep all cigarettes, sparks or flame away from the battery and all fuel related parts. 1.4 Specifications Overall Length: 66″ Body Length: 92″ Wheel Base: 53″ Load Capacity: 620 Lb Tire Size (15″): 205 / 70 / R15 Wheel Size (15″) (4 lug) Offset +35 mm 15x7JJ 4×4.5 – (Current Installations – Alum Rear End) Wheel Size (15″) (5 lug) Offset +35 mm 15x7JJ 5×4.5 – (Later Installations – Black Rear End) Tire Size (16″) 215 / 60 / R16 Wheel Size (16″) (5 lug) Offset +40 mm 16x7JJ 5×4.5 – (First Installations – Black Rear End) Tire Pressure: 20 PSI Suspension: Internal Swing Arm utilizing OEM shocks Rear Differential: Custom-built rear differential utilizing OEM drive belt. Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 3.75 cubic feet. 2 full-face helmets and additional storage

Harley davidson American Classic Straights on a 1988-2001 VLX 600 Shadow Installation Instructions

0

Filed Under (Harley Davidson) by admin on 01-03-2012

download
Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove bolts that are holding pipes at rear mounting bracket. 3. Loosen clamps at mufflers. 4. Remove mufflers. 5. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 6. Remove rear exhaust pipe assembly. 7. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 8. Remove front exhaust pipe assembly. 9. Remove exhaust-mounting bracket from frame. Hard-Krome Exhaust System Installation NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design, configuration and location. WARNING : Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessary on a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system.
1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. (See Illustration) 3. Install Front exhaust header pipe, taking care to not scratch chrome surfaces on pipe, engine or motorcycle — use masking tape as needed. 4. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 5. Install nut strip into slotted bracket of front pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 6. Carefully install rear pipe. 7. Install the two nuts to secure the flange that holds the exhaust header pipe to the rear cylinder head — DO NOT TIGHTEN NUTS! 8. Install nut strip into slotted bracket of rear pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 9. Tighten the two bolts that secure the rear exhaust header pipe flange. 10. Tighten the two bolts that secure the front exhaust header pipe flange. 11. Tighten front pipe bolts at mounting bracket. 12. Tighten rear pipe bolts at mounting bracket. 13. Reinstall foot peg assembly or floorboard. 14. If applicable to your model install foot peg relocating brackets and foot pegs as shown in illustration. 15. Before starting bike wipe off any fingerprints and grease off pipes. Start bike and check for any exhaust leaks.

Incoming search terms:

HARLEY DAVIDSON DYNA SIDESHOTS BLACK INSTALLATION AND REMOVAL PROCEDURE

0

Filed Under (Harley Davidson) by admin on 25-02-2012

download
Remove seat to gain access to rear oxygen sensor connector. Unplug sensor and feed end of wire through frame so that it is free from motorcycle. NOTE: Pay attention to wire routing for re-installation. 2. Remove two bolts holding rectifi er onto front of frame (near front tire). Open plastic cover to gain access to front oxygen sensor connector. Unplug sensor from harness. Remove cable tie holding wire to frame and feed end of wire through so that it is free from motorcycle. 3. Loosen heat shield clamps on both the front and rear head pipes. 4. Remove two cylinder exhaust port fl ange nuts from each head pipe, located at the cylinder head. 5. Remove front head pipe clamp bolt. 6. Remove the bolt that attaches muffl ers to the frame mounting bar. 7. Remove the complete exhaust system and set aside. Assistance may be required. 8. Remove stock mounting bar and the studs in the transmisson cover. Save the bolts, one will be re-used. 9. Remove left bolt below the transmission cover. Position mounting bracket 405-P over mounting location to determine which bolts to remove (Figure 1). Install this bolt in the top hole left vacant by the new bracket. 10. Carefully remove the fl anges and circlips from the stock exhaust system using snapring pliers. NOTE: Replace bent or damaged circlips. Check condition of stock exhaust gaskets. Replace if worn or damaged. (Recommended replacement exhaust port gaskets, Screamin’ Eagle part number 17048-98)

2007 SUZUKI SV650 CUP RULES

0

Filed Under (Suzuki) by admin on 22-02-2012

download
suzuki SV650 Cup motorcycles must meet the requirements of Lightweight Sportbike Equipment except as noted: a) The exhaust system may be replaced with commercially available aftermarket exhaust systems meeting mandatory track noise limits. b) The rear shock may be replaced with an after-market shock. c) Front forks must remain stock. Internal springs, valving, and oil may be changed with any aftermarket components. d) All riders must race on the same brand of tires. For 2007 the spec tire will be Pirelli . The Pirelli SuperCorsa Pro 120/70-17 SC1 (Super Soft) front and the Pirelli SuperCorsa Pro 160/60-17 SC2 (Soft) rear for dry weather and the Diablo Rain 120/70-17 SCR1 (Super Soft) front, 160/60-17 SCR1 (Super Soft) rear for wet weather conditions. e) Steel braided brake lines may be used to replace stock lines. Calipers and rotors must remain stock. (After market brake pads are acceptable.) f) Horsepower limit: 75hp measured at the rear wheel (Sanctioning body to enforce if required). g) Suzuki SV Cup Machines must weigh no less than 365 pounds in the same condition in which they finish the race, including all fluids such as oil, water and fuel. Weights will be checked immediately following races, and no fluid may be added prior to the determination of weight or before the post race horsepower check on the dyno.

Incoming search terms:

Suzuki M- 109 Front Head Pipe Installation Manuals

0

Filed Under (Suzuki) by admin on 18-02-2012

download
1. Remove seat (Fig 1) remove right side (Fig 2) panel with allen 6mm bolt and push-pin snap. (Fig 3) Figure 1 Figure 2 Figure 3
- 3 – 2. Remove 6mm bolt on heat shield and remove heat shield. (Fig 4) Figure 4 3. Remove two 8mm bolts on top muffler and remove two 8mm stock bolts on bottom muffler and remove mufflers. (Fig.5 & 6) Figure 5 Figure 6 4. Remove frame cover with stock allen 6mm bolt. (Fig 7) Figure 7 FFF – 4 – 5. Loosen brake pedal bolts to allow more room to remove the exhaust. (Fig 8) Figure 8 6. Remove exhaust system by removing stock 8mm bolts on exhaust flanges. (Fig 9) Figure 9 7. Unplug EXCVA wire connectors. (Fig 10) Figure 10 – 5 – 8. Remove three 8mm stock mufflers mounting brackets bolts as shown. (Fig 11) Figure 11 ffff 9. Remove EXCVA unit from the stock muffler bracket. (Fig 12) Figure 12 10. Remove the stock pulley from the EXCVA actuator unit as shown. (Fig 13)

Incoming search terms:

SUZUKI GSR 600 Accessories

0

Filed Under (Suzuki) by admin on 12-02-2012

download
YBA – Pearl suzuki deep blue no.2 P/N 99000-99074-69N YD8 – Metallic sonic silver P/N 99000-99074-70N YHL – Candy sonoma red P/N 99000-99074-71N YKV – Metallic matt black no.2 P/N 99000-99074-72N YAY – Pearl nebular black P/N 000-99074-73N YMD – Metallic mistic silver P/N 99000-99074-74N YME – Candy max orange P/N 99000-99074-75N YLF – Metallic thunder gray P/N 99000-99074-76N 1 Not in combination with crash pad set (pos. 110) From exhaust to cockpit: the GSR600 is all dressed up 3 102 103 104 106 107 105 102 GSR600 exhaust system by Yoshimura 1 GSR600, model year 2006-2009 P/N 99000-79N12-023 103 Chain guard GSR600, model year 2006-2009 Polished aluminium P/N 990D0-44G10-000 104 Frame covers set GSR600, model year 2006-2009 Carbon look P/N 990D0-44GFC-CRB 105 Tankpad P/N 990D0-44G00-PAD 106 Rear lamp cover GSR600, model year 2006-2009 For original equiped exhaust system P/N 990D0-44G25-PAD For Yoshimura exhaust system P/N 990D0-44G30-PAD 107 Ignition lock cover GSR600, model year 2006-2009 P/N 990D0-44G15-PAD 108 Speedometer cover GSR600, model year 200

1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

Yamaha 1999-2002 YZF-R6 TiForce exhaust system Installation Instructions (full system)

0

Filed Under (Yamaha) by admin on 12-01-2012

download
1. Remove the lower fairing. Remove the lower radiator mounting bolts, loosen the upper bolts and pivot the radiator forward to provide more access to the exhaust nuts (flange nuts). 2. Remove the existing exhaust system and save the flange nuts for reuse. Save the mounting bolt and nut for the end can to the passenger footpeg for reuse as well. 3. Inspect the exhaust gaskets. Replace if necessary. 4. Assemble the head pipes 1, 2, 3 , and 4 by matching the joints of the same color to the pair of front Y-pipes. Do not install the exhaust springs at this time. 5. Attach the assembled head pipe sections to the exhaust ports, but do not tighten the flange nuts fully, allowing for some adjustment in the remainingsteps. Reuse the flange nuts saved from step 3 above. Make sure the ends of the headpipes fit flush and snug in the ports before tightening. 6. Install the S-Bend to the front section of the headpipes and two Y-pipes. 7. Go back and retighten the head pipe flange nuts per factory specifications. 8. Slide the TiForce end can into place. Loosely attach the two rubber bands, stainless steel bands K, and stayarm / hanger G to the end can using the supplied 6mm hardware H. (See figure 1) . 9. Place the bands approximately 195mmfrom the edge of the end can. (See figure 2) . 10. Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 11. Attach the supplied springs to all the joints, starting from the headpipes and working back to the end can. 12. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance

Yamaha YZF-R1 and R6 TiForce slip on exhaust system REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 09-01-2012

download
1. Remove the fairing lowers. 2. For R1 owners, please remove the existing exhaust system from the EXUP valve rearward (EXUP valve is retained) and set aside. Save the stock exhaust clamp for reuse. For R6 owners, please disconnect the stock S-bend from the rear of the collector and set aside. Save the stock exhaust clamp for reuse (new clamp provided). Save the stock end can mounting bolt for reuse as well. 3. R1 owners only -Inspect the exhaust gasket. Replace if necessary (gasket provided). 4. For R1 owners -Install the S-Bend to the rear of the EXUP valve, make sure the system fits flush. Reuse the stock exhaust clamp to connect the S-bend to the valve. For R6 owners -Install the TiForce S-bend to the rear of the stock head pipes and collector. Make sure the system fits flush and snug. Reuse the stock exhaust clamp or the provided clamp and loosely attach for now. 5. Install the TiForce end can to the S-bend tail pipe. 6. Loosely attach the two rubber bands, stainless steel bands (K), and stay to the end can using the supplied 6mm hardware (H) and the hanger / stay arm (G). See figure 1 for the assembly procedure. 7. R1 owners -Place the bands approximately 180mm from the edge of the end can. See figure 2. R6 owners -Place the bands approximately 195mm from the edge of the end can. See figure 2. 8. R1 owners -Using the stock provided mounting point on the passenger footpeg, use the M10x45mm bolt and hardware to mount the end can loosely, allowing for some adjustment. 9. Carefully align the two stainless bands so that theyare parallel to each other, and spaced properly on the can. Tighten the 6mm hardware (H). Make sure that the rubber pads fully cover the bands (K). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. 10. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire TiForce exhaust system to remove any residual oils, anti seize, fingerprints and dirt prior to starting the motor. FAILURE TO CLEAN THE TUBING AND CAN MAY RESULT IN PERMANENT STAINING OF THE SYSTEM WHEN HEATED. 11. Attach the supplied springs to secure the end can to the S-bend pipe using a spring installation tool if available. Make sure the exhaust system is free and clear of the bike. If necessary, adjust for proper clearance. 12. Go back and tighten all fasteners. 13. Check that all fasteners are tightened per specifications, then start the motor and check for exhaust leaks. 14. Reinstall the fairing lowers.

Incoming search terms:

Yamaha XVS 13AW Owner's Manual REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 06-01-2012

download
GASOLINE IS HIGHLY FLAMMA- BLE: Always turn the engine off when refueling. Take care not to spill any gasoline on the engine or exhaust system when refueling. Never refuel while smoking or in the vicinity of an open flame. Never start the engine or let it run for any length of time in a closed area. The exhaust fumes are poisonous and may cause loss of consciousness and death within a short time. Always operate your motorcycle in an area that has adequate ventilation. Always turn the engine off before leaving the motorcycle unattended and remove the key from the main switch. When parking the motorcycle, note the following: The engine and exhaust system may be hot, therefore, park the motorcycle in a place where pedestrians or children are not likely to touch these hot areas. Do not park the motorcycle on a slope or soft ground, otherwise it may fall over. Do not park the motorcycle near a flammable source, (e.g., a kerosene heater, or near an open flame), otherwise it could catch fire. When transporting the motorcycle in another vehicle, make sure that it is kept upright. If the motorcycle should lean over, gasoline may leak out of the fuel tank. If you should swallow any gasoline, inhale a lot of gasoline vapor, or allow gasoline to get into your eyes, see your doctor immediately. If any gasoline spills on your skin or clothing, immediately wash the affected area with soap and water and change your clothes

Incoming search terms: