YAMAHA ROADLINER / STRATOLINER REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 04-01-2012

download
1. Cover the right frame tube in front of the exhaust with duct tape or any suitable material to protect frame during exhaust removal. 2. Remove the three capscrews holding the muffl er assembly to the support bar, loosen the muffl er clamp and carefully remove the muffl er from the motorcycle. 3. Remove and save the two 12mm bolts from the right side fl oorboard assembly (Figure 1) and carefully lower the fl oorboard out of the way. NOTE: Support the fl oorboard with a block of wood or other appropriate material, do not let it “hang” by the brake switch wire. 4. Remove the chrome cover over the power valve pulley. Using a 10mm wrench, remove both cables attached to the power valve pulley (Figure 2). 5. Remove and save the 5mm capscrew on the rear side cover to gain access to the O2 sensor harness plug and unplug O2 sensor from harness (Figure 3). 6. Remove the 4 nuts holding the exhaust system and carefully remove the exhaust system from the motorcycle (may require assistance). NOTE: It may be necessary to loosen the heatshield clamps to access the nuts on the front cylinder. 7. Trace the power valve cables to the drive motor (just under the rear fender on the right side). Remove the power valve cables and mounting clips from the motorcycle. 8. Using a 22mm wrench, carefully remove the O2 sensor from stock exhaust system and save for reuse with the new system. 9. Remove the plastic cover over the clutch banjo bolt (Figure 4). 10. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them

Yamaha FZ-1 TiForce exhaust system Installation Instructions (Slip-on)

0

Filed Under (Yamaha) by admin on 03-01-2012

download
Loosen the clamp where the stock tailpipe connects to the stock collector. 2. Remove the bolt holding the stock muffler assembly to the footpeg/exhaust bracket. 3. Remove the stock tailpipe and exhaust assembly as one piece. 4. Remove the nut securing the right side center stand support bolt. Install the new supplied bracket as shown in (See figure 1) 5. Remove the right rear footpeg assembly complete, bolt the new footpeg mounting bracket in place of the stock one using supplied bolts. 6. Carefully unbolt the footpeg from the bracket (Be careful there are springs and washers that will fall out if you are not careful), bolt the footpeg into the new billet footpeg bracket. Bolt the footpeg bracket to the footpeg- mounting bracket. (See figure 2) 7. Remove the stock exhaust gasket from the stock tailpipe and installthe gasket into the new tailpipe. 8. Slide the supplied clamp over the new tailpipe and slide the new tailpipe onto the stock collector. 9. Slide the TiForce end can into place. Loosely attach the two rubber bands, stainless steel bands K, and stayarm / hanger G to the end can using the supplied 6mm hardware H. See figure 4. 10. Place the bands approximately 150mm from the edge of the end can. See figure 5. 11. Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 12. Attach the supplied springs to connect the tailpipe and muffler assembly. 13. Make sure the exhaust system is free and clear, if necessary jigglethe system to adjust for proper clearance. 14. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can (figure 5), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure thatthe rubber pads fully cover the band(s). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. 15. Tighten the supplied clamp to secure the new tailpipe to the factory collector. 16. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire exhaust system to remove any residual oils, anti seize, fingerprints and dirt prior to starting the motor. FAILURE TO CLEAN THE TUBING AND CAN MAY RESULT IN PERMANENT STAINING OF THE SYSTEM WHEN HEATED. 17. Check that all hardware is tightened, then start the motor and check for exhaust leaks.

Yamaha V-Star 1100 Needle/ Jet Kit REMOVAL AND INSTALLATION MANUALS

0

Filed Under (Honda) by admin on 27-12-2011

download
To install this needle and jet kit: • Remove carburetors from the engine per Yamaha shop manual procedures. Note: Always perform internal carburetor work in a clean area. • Remove the vacuum slide from each carburetor. • Remove the OEM needle, spacer and washers, noting order of assembly. (Note; the washers are used as shims to raise the needle, each is equivalent to ½ clip position, use these to fine tune the needle) • Counting from the top to the bottom, install the new Baron needle clip on groove #4 of the replacement Baron adjustable needles. The top is the blunt end of the needle. • Reinstall the OEM spacer and washers as shown in the figure below. • Reinstall the vacuum slides along with the diaphragm spring and reattach the diaphragm covers Note: Verify that the slides maintain their full range of movement! • Drain the fuel from the float bowls and remove the bowl covers. • Remove the OEM main jets and replace them with Baron’s supplied Mikuni main jets. Install the “base setting” main jets as indicated above. NOTE: V-Star 1100 carburetion runs staggered jetting! Make sure the front cylinder’s carburetor gets the larger main jet (numerically), and the rear cylinder’s carburetor gets the smaller main jet . Important! Extra jets have been included in your kit. These will help you fine-tune the carburetors for changing conditions. These conditions include climate and weather patterns in your area as well as exhaust equipment on your motorcycle. Barons determines the jet and clip recommendations that best suit your average riding conditions based upon information supplied to us at the time of your order. Changes in weather, altitude or modifications to your exhaust system may require jets other than those supplied. • Thoroughly clean the inside of the float bowls prior to reinstalling them. 311 #1 Industrial Way – Fallbrook, CA 92028 – USA Phone: (760) 731-1200 Fax: (760) 731-1284 E-mail: tech@baronscustom.com Website: www.baronscustom.com Included in this kit: (4)Mikuni main jets #107.5, 110, 112.5, 115, (2) titanium needles, (2) clips, (8) cap-head allen screws Tools required: 3-4-5 mm allen wrenches, 10&12 mm sockets, 10mm end wrench, phillips & flat screwdrivers, pliers, drill. Revision 4.0 • Reassemble the carburetors by reversing the order of above steps. Use the new supplied cap head Allen screws in place of the OEM Phillips head screws for the float bowls. • Locate the fuel mixture screws – they will either be a screw head or a brass plug. If it is a screw head, skip to step c . If you see a brass plug with a small hole in the center, proceed as follows: a. With a 5/32″ drill bit, carefully and slowly drill through the fuel mixture plugs

Incoming search terms:

Honda TRX 400EX INSTALLATION And REMOVAL INSTRUCTIONS

0

Filed Under (Honda) by admin on 14-12-2011

download
Quiet cores are supplied with this kit but not installed. To install the quiet cores remove both rear end caps ((turn downs) and install the quiet cores with the tubes facing inward. Re-install the end caps. REMOVAL Remove seat, disconnect attery and remove. Remove front fenders and side skirts. Remove fuel tank (make sure to shut fuel off and drain remaining fuel in the line before removing). Remove stock muffler first, then remove stock headers. Retain the 4 stock header bolts to install on your new exhaust system. Remove the rear bolt from your stock air box. Loosen stock intake clamp at carburetor. Remove stock boost bottle from the side of the boot. Loosen stock snorkel clamp at the air box, remove stock retaining clip at the front of the snorkel. Remove stock air box, intake boot and snorkel together from the ATV. Slide tarter solenoid off of stock mounting prongs. Remove Phillips screws from fuse holder and remove from plastic housing. Remove plastic battery housing from the ATV. Unplug tail light from harness. Unclip harness from the 2 clips above the battery. CARBURATION Now would be a good time to replace your stock main jet, with the supplied 190 main jet and replace your stock pilot jet with the supplied 48 pilot jet. Make certain that all hoses are tight and routed as stock. Be certain carb clamp is tight when re-installed. INTAKE BOOT Remove the intake boot from the stock air box. Take an exacto knife or razor blade and trim off the rubber piece that the hard plastic snorkel slips into. Trim around the intake boot staying the same distance as the rest of the lip. Take a hax saw and cut the groove as the rest of the boot is, being
careful not to cut all the way through (Picture Fig.2).

2007-2008 HONDA CBR 600RR DUAL CANISTER SLIP- ON INSTALLATION

0

Filed Under (Honda) by admin on 04-12-2011

download
INSURE THE EXHAUST SYSTEM AND EXHAUST COMPONENTS ARE FULLY COOLED. 2. INSURE THE MOTORCYCLE IS STABLE ON KICKSTAND OR REAR CENTERSTAND OR SERVICE TABLE. 3. REMOVE BOTH THE FRONT AND REAR SEATS. 4. REMOVE THE 4 BOLTS HOLDING THE TAIL
FAIRING TO THE SUBFRAME AND REMOVE THE TAIL FAIRING. REMOVE 5. REMOVE TRIM PLASTIC JUST ABOVE RIGHT SIDE FOOTPEG. (REMOVE THE ONE BOLT AND UNCLIP) TRIM PLASTIC UNCLIP REMOVE 6. REMOVE LOWER FOOT PEG BRACKET AND REMOVE THE HEAT SHIELD BOLT. ALLOW THE FOOT PEG BRACKET TO HANG BY THE HOSE AND WIRES

2006-2007 Honda TRX450R SR4 4 Stroke racing system INSTALLATION

0

Filed Under (Honda) by admin on 30-11-2011

download
Install Motoworks header pipe using stock nuts, finger tight at this point ( Fig 4) 2. Install Motoworks tailpipe with muffler using bolt and spacer supplied in kit on upper rear mount, use stock nut and bolt on lower mount finger tight at this point. (Fig 5 and 6) 3. Torque header pipe nuts to 1.0 kg-m ( 7.3 lb-ft ) 4. Torque tailpipe mounting bolts to 2.5 kg-m ( 18 lb-ft ) 5. Re-check all your work 6. We recommend that you clean the entire exhaust system with a mild detergent, i.e. glass cleaner prior to starting as any oily residue may cause permanent stainingBefore operating check for proper clearance between Motoworks exhaust and ATV i.e. frame, plastic, brake line, fuel line etc if problems exist re-check work

Honda RC-51 / VTR-1000 SP1 – Installation Instructions

0

Filed Under (Honda) by admin on 23-11-2011

download
Remove the lower fairing. Remove the existing exhaust system from the mid pipes rearward. Save the exhaust clamps for reuse Save the stock exhaust can mounting bolts and nut for the end can to the passenger footpegs for reuse as well. Inspect the original exhaust gaskets. Replace as necessary. Slide the tail pipes into place. Do not tighten the clamps at this point. Slide the TiForce end cans into place. Loosely attach the two rubber bands, stainless steel bands K, and stay / hanger G to each end can using the supplied 6mm hardware H. See figure 1 for details. Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G
(see figure 1). Attach the supplied springs to all the joints (from the tail pipes to the TiForce end cans). Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can, then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure that the rubber pads fully cover the band(s). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO
BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN(s).

2008-2009 HONDA CBR 1000 RR DUAL CANISTER SLIP-ON INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 22-11-2011

download
INSURE THE EXHAUST SYSTEM AND EXHAUST COMPONENTS ARE FULLY COOLED. 2. INSURE THE MOTORCYCLE IS STABLE ON KICKSTAND OR REAR CENTERSTAND OR SERVICE TABLE. 3. REMOVE THE 3 PLASTIC BUTTONS HOLDING THE PLASTIC COVER OVER THE EXHAUST SERVO. (THIS IS LOCATED DIRECTLY INSIDE THE RIGHT REAR PASSENGER PEG BRACKET) DETACH THE CABLE END FROM THE SERVOnWHEEL AND REMOVE THE ENTIRE CABLE FROM THE RETAINING CLIP. THE ENTIREnCABLE WILL NOW REMOVE WITH THE REST OF THE EXHAUST.REPLACE THE PLASTIC COVER FOR THE SERVO AND REINSTALL THE 3 PLASTIC BUTTONS. 6. REMOVE THE STOCK MUFFLER MOUNTING BOLT. REMOVE 7. REMOVE THE STOCK EXHAUST CLAMP. (IT IS NOT UNCOMMON FOR THE CLAMP BOLT TO BREAK DURING REMOVAL.)b8. REMOVE THE ENTIRE STOCK EXHAUST ASSEMBLY. BE CAREFUL NOT TO SCRATCH THE SWING ARM DURING REMOVAL. 9. REMOVE THE STOCK EXHAUST GASKET FROM HEADER PIPE IF IT DID NOT COME OFF WITH THE STOCK EXHAUST. THIS GASKET WILL
NOT BE USED. 10. PREASSEMBLE THE HYPERFLO EXHAUST BEFORE INSTALLING. HYPERFLO RECOMMENDS YOU DO THIS PORTION ON CARPET OR A CLEAN PADDED AREA. YOU MAY ALSO USE THE PLASTIC BUBBLE PACKAGING AS A PAD TO PROTECT THE CANISTERS DURING PREASSEMBLY. 11. PREASSEMBLE THE LARGE DIAMETER CAN TO THE S-PIPE FIRST. INSTALL THE SPRING ON THE CANISTER FIRST AND PULL AWAY FROM THE CANISTER TO INSURE YOU DO NOT SCRATCH THE CANISTER

HONDA SHADOW AERO 750 STRAIGHTSHOT HS EXHAUST SYSTEM

0

Filed Under (Honda) by admin on 03-11-2011

download
Install mounting bracket (stamped 359-P) in the original bracket mounting position, using two 10mm bolts and
one 10mm nut (supplied)(Figure 2). 2. Remove head pipes and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark the outside edge of each heat shield to show location of hose clamp mounting clips (Figure 3). 3. Slide flanges onto head pipes and lay head pipes into
heat shields. Loosely install hose clamps by feeding tail end of clamp into heat shield clips (Figure 3). Take note of screw head direction (Figure 4). Screw head should be accessible when system is installed on motorcycle for adjustment purposes. Use #20 hose clamps for head pipe areas and #28 hose clamps for muffler areas.
4. Using stock nuts, carefully install head pipes into exhaust ports (Assistance may be required). NOTE: Do not tighten at this time.

TOYOTA L, 2L ENGINE REPAIR MANUAL FOR 2L-T ENGINE DESTINATIONS FUEL SYSTEM

0

Filed Under (Toyota Manuals) by admin on 21-05-2011

Download
INSUFFICIENT TURBOCHARGING PRESSURE Check turbocharging pressure (See page EM-6). If not within the  standard shown below, begin diagnosis from item 2. Standard pressure: 0.41 – 0.54 kg/cm2 (5.8 – 7.7 psi, 40 – 53 kPal RESTRICTED INTAKE AIR SYSTEM Check intake air system, and repair or replace parts as necessary. (See page EM-6)
3. LEAK IN INTAKE AIR SYSTEM Check intake air system, and repair or replace parts as necessary. (See page EM-6)
4. RESTRICTED EXHAUST SYSTEM Check exhaust system, and repair or replace parts as necessary, (See page EM-6)
5. LEAK IN EXHAUST SYSTEM Check exhaust system, and repair or replace