Harley-Davidson CHROME HANDLEBAR SWITCH CAP KITS installation and REMOVAL manual

0

Filed Under (Harley Davidson) by admin on 09-03-2012

download
1. Open or remove seat according to the instructions in the Service Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Disconnect battery cables, negative (-) cable first. 3. Remove left and right-hand switch housing assemblies. Refer to HANDLEBAR SWITCHES in Service Manual. NOTE It is not necessary to disconnect the switch wiring to replace the switch caps. 4. Remove individual switches from switch housing. Refer to SWITCH REPAIR/REPLACEMENT in Service Manual. INSTALLATION Upper Housing Switches 1. For HORN and START switch caps, release torsion spring leg from hole in switch cap tab. Take note of how the spring is installed. The other leg of the spring can remain in the switch bracket hole. 2. See Figure 1 and Figure 5. Carefully pry stock black switch cap up off the splined actuator shaft (2) on left side of switch. -J02633 1 of 5 5 2 1 1 3 4 is 01405 1. Switch cap installed correctly 2. Switch cap removal from splined shaft 3. Switch cap removal from pivot pin 4. Switch cap installation onto pivot pin 5. Switch cap installation onto spined shaft Figure 1. Switch Cap Removal and Replacement 3. Pry the switch cap up and away from pivot pin (3) on right side of switch, and remove cap. NOTE Use the clear protective cover film to protect the chrome surface of the switch caps during installation. Remove the film after the installation is complete. 4. See Figure 5. Select proper chrome replacement switch cap from kit. 5. See Figure 1. Place cap onto switch, angling the hole on right side over pivot pin (4) on switch. 6. Carefully press switch cap down onto splined actuator shaft (5), rocking and moving the cap until shaft snaps into place in splined hole. 7. For HORN and START switch caps, insert torsion spring leg into hole in switch cap tab. 8. Toggle switch back and forth, checking for proper opera- tion. Turn Signal Switches 1. See Figure 1 and Figure 5. Carefully pry stock black switch cap up off the splined actuator shaft (2) on switch. 2. Pry the switch cap up and away from pivot pin (3) on switch, and remove cap. 3. Select proper chrome replacement switch cap from kit. Peel a clear protective installation cover from the sheet and place it over the surface of the cap. 4. See Figure 1. Place cap onto switch, angling the hole on top over pivot pin (4) on switch. 5. Carefully press switch cap onto splined actuator shaft (5), rocking and moving the cap until shaft snaps into place in splined hole. 6. Toggle switch back and forth, checking for proper opera- tion.

Incoming search terms:

HARLEY DAVIDSON POWER LOCK KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-04-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery, negative (-) battery cable first, following the instructions in the appropriate Service Manual. 2. Remove seat following the instructions in the appropriate Service Manual. Preparing the Saddlebags for Power Locks 1. Remove saddlebags following the instructions in the appropriate Service Manual. 2. See Figure 1. Remove lid (1) and hinge (2) from sad- dlebag. 3. Remove lock (3) from saddlebag. 4. See Figure 2. Set drill template on hinge surface of the saddlebag aligning the template (5) with hinge mounting holes (7). 5. See Figure 3. Drill 0.344 (11/32) inch diameter hole (1). 6. Place the template on the back of the saddlebag (4) aligning front mounting grommet (2) and forward latch bracket (1). 7. See Figure 4. Drill 0.500-0.515 inch diameter hole (1). 8. Repeat on the other saddlebag. 1 2 3 is04988 1. Saddlebag lid 2. Saddlebag hinge 3. Saddlebag lock Figure 1. Remove Lid, Hinge and Lock from Saddlebag

HARLEY DAVIDSON NARROW BEACH HANDLEBAR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-04-2011

download
INSTALLATION Preparation To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the battery cables, negative cable first. Retain all seat mounting hardware. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. Loosen the fuel tank. Refer to FUEL TANK REMOVAL in the appropriate section (Carbureted or EFI Engine) of the Service Manual. Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a

HARLEY DAVIDSON SOFTAIL 6 SPEED TRANSMISSION – COMPLETE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-04-2011

download
Removal of Original Transmission 1. Position motorcycle on a suitable lift. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the battery cables, negative cable first. 3. Refer to the TRANSMISSION CASE REMOVAL in the Service Manual and follow the instructions given to remove the components with the following steps. 4. Refer to PRIMARY CHAINCASE COVER REMOVAL in the Service Manual and follow the instructions given to remove the primary chaincase cover. Wear safety glasses or goggles when removing or installing retaining rings. Retaining rings can slip from the pliers and could be propelled with enough force to cause serious eye injury. (00312a) 5. See the PRIMARY CHAIN and COMPENSATING SPROCKET REMOVAL in the Service Manual and use the instructions given to remove the primary drive assem- bly. 6. Refer to the STARTER REMOVAL in the Service Manual and remove the the starter. 7. See the VEHICLE SPEED SENSOR section and unplug the vehicle speedometer sensor connection and remove the mounting bolt. Lift sensor from the transmission case and set aside for later re-installation. 8. Refer to NEUTRAL SWITCH and disconnect the connectors from the neutral switch. 9. Refer to PRIMARY CHAINCASE in the Service Manual and follow the instructions given to remove the primary chaincase housing. 10. Refer to EXHAUST SYSTEM in the Service Manual and remove the exhaust. 11. See the REAR WHEEL REMOVAL and loosen but, do not remove rear axle to relieve drive belt tension and remove the belt from the sprocket from the transmission. 12. Refer to OIL TANK REMOVAL in the Service Manual and follow the instructions given to drain, remove the oil tank and detach the vent, feed and return lines. 13. Refer to CLUTCH CONTROL in the Service Manual and follow the instructions given to remove the clutch cover and disconnect the clutch cable end from the cover. Set the cable aside for later re-installation

Incoming search terms:

HARLEY DAVIDSON HIGH INTENSITY DISCHARGE (HID) DUAL BULB HEADLAMP KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
REMOVAL 1. Remove seat according to the instructions in the service manual. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. 2003-Earlier Models: Disconnect battery cables, negative (-) cable first. Refer to the service manual. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 3. 2004-Later Models: a. Remove left saddlebag. Refer to the service manual. b. Remove left side cover and main fuse. Refer to the service manual. 4. Remove fuel tank according to the instructions in the service manual. 5. See Figure 1. Remove the Phillips screw (1) at the bottom of the bezel and remove the bezel. Save parts for installa- tion. 1 2 is03916 1. Phillips screw 2. Bezel Figure 1. Remove Bezel 6. See Figure 2. Remove and save Phillips screws (1) that secure mounting ring assembly (2) to nacelle. 7. Gently pull headlamp assembly out far enough to disconnect wiring. Save short wire harness for installation. 8. Remove wire connector at the back of the headlamp bulb. 9. See Figure 2. Remove three screws (3) securing the retaining ring (4) and headlamp assembly to mounting ring assembly. Discard mounting ring assembly, but save three screws and retaining ring for installation

HARLEY DAVIDSON DYNA BATTERY COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-03-2011

download
INSTALLATION 1. Remove seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Disconnect battery cables, negative cable first. 3. Follow instructions in applicable Service Manual to loosen and lower battery tray. 4. Remove top and side covers and discard. 5. See Figure 1. Install cover from kit as follows: a. Align bottom of cover with tray (2) making sure that three clips on bottom properly seat (center) on both sides of retaining lip (6) at the base of the battery tray. b. Position top of cover (5) under the frame tube. 6. Raise tray and cover following instructions in Service Manual and tighten bolts (3,4) securely. 5 3 2 1 4 6 is 01648 1. Battery 2. Battery tray 3. Upper mounting bolt 4. Lower mounting bolt 5. Battery cover 6. Retaining lip Figure 1. Battery Cover and Mounting Hardware Connect positive (+) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00068a) 7. Connect battery cables, positive cable first. 8. Install seat

HARLEY DAVIDSON HARDWARE/ TURN SIGNAL RELOCATION KIT FOR SPORTSTER LEATHER SADDLEBAG KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-03-2011

download
Installation Instructions for 79052-04 and 79073-04 Do not exceed 7 lbs (3.17 kg) maximum load in each saddlebag. Additional weight can affect a motorcycle’s stability, handling characteristics, and safe operating speed which may lead to an accident resulting in death or serious injury. NOTE A pick tool (Snap-on TT600-3) will be required for 1996 and later models for removing and reinstalling a multi-lock amp con- nector. NOTE A Service Manual for your vehicle is available from your Harley- Davidson Dealer. Installation – Hugger Models Only (1994-1997) To perform the following steps for Hugger Models only, fender and frame must be sufficiently supported, as both shocks will need to be removed at the same time. An improperly supported vehicle could result in death or serious injury. A Service Manual is needed to install this kit. The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have your Harley-Davidson Dealer perform the installation. Improper installation of this kit could result in death or serious injury. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Remove seat, sissy bar and sideplate, if applicable. Retain hardware for reinstallation. Disconnect battery, negative cable first. 2. Properly support motorcycle under frame to prepare for removal of right and left shocks. 3. Remove rear buttonhead screw on each side of fender. 4. See Figure 1. With rear fender and frame securely supported, remove left and right shocks by removing upper nut (2), washer(s) (3) and shock cover (4). Remove bolt (6), washer (7) and locknut (8) at lower shock mount. Remove shock

HARLEY DAVIDSON VRSC TURN SIGNAL RELOCATION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
INSTALLATION Removing Turn Signals To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Remove the 40 amp Maxi-Fuse or disconnect the battery cables, negative cable first. Never touch the quartz bulb. Fingerprints will etch the glass and decrease bulb life. Grab the bulb with paper or a clean, dry cloth. Failure to do so could result in bulb damage. (00210a) 2. For VRSCA models, remove headlamp assembly. For VRSCB models, continue to Step 4. a. While facing the headlamp from behind (looking toward front of motorcycle), reach behind the headlamp bucket and twist the headlamp bulb approximately 45 degrees counterclockwise, then gently pull straight out of the headlamp. Repeat for remaining bulb. Temporarily secure bulbs out of the way for the following steps. b. See Figure 1. Remove the two mounting screws securing the headlamp bracket to the upper triple clamp and remove headlamp assembly. Save hard- ware

HARLEY DAVIDSON SECURITY SYSTEM SMART SIREN AND SMART SIREN II KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
INSTALLATION 1. Refer to the owner’s manual and follow the instructions given to disarm the security system and remove the left- side cover. Models with main FUSE: To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. Refer to the owner’s manual and follow the instructions given to remove the main fuse. ALL models: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 3. Refer to the owner’s manual and follow the instructions given to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. NOTE For 2004 and later XL (Sportster┬«) models, the negative battery cable is most easily disconnected at the engine crankcase . 4. Remove the battery from the vehicle. 2 1 3 4 is 01377 1. Three-pin connector on siren harness 2. Three-pin connector [142B] on vehicle harness 3. Siren harness 4. Frame rear crossmember (not visible) Figure 1. Connect the Siren Harness to the Vehicle Harness 5. See Figure 1. Locate the siren connector (2) on the main harness, behind the harness shield forward of the battery location. It is covered by a dust cap. Pull the dust cap from the connector, and feed the connector downward and out from behind the shield. 6. Select the correct siren harness (3) for this model year vehicle from the kit. Route the three-pin connector (1) of the siren harness from the bottom of the motorcycle, between the primary cover and frame tube. Plug the connector into the siren harness connector (2) on the vehicle main harness. 7. Secure the connectors to the diagnostic harness using a cable strap from the kit. Route the long lead of the siren harness over the frame rear crossmember

HARLEY DAVIDSON AUXILIARY LAMP WITH CLEAR LENS AND VERTICAL REFLECTOR OPTICS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
1. Disconnect the battery cables, negative cable first. 2. See Figure 1. Remove passing lamp molding screw (1) and nut (2) from passing lamp molding (3). Remove molding and hardware. Retain for future use. 3. Disconnect the wire harness plug from back of auxiliary lamp assembly (4). 4 See Figure 2. Remove assembly (1) and nesting ring (2). Discard lamp but retain nesting ring. 5. Place the nesting ring at back of new lamp with concave side facing away from lamp. Install new harness provided in kit. Attach leads to the wires inside the lamp hous- ing. 6. Connect new wire harness to the new lamp. Locate lamp in housing and be sure to align tabs on lamp (3) with pockets in the nesting ring. 7. Install passing lamp molding over lamp. Rotate lamp molding so that screw is centered at bottom. Install nut and screw and secure until snug. 8. Repeat for the lamp on the opposite side. Connect positive (+) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00068a) 9. Connect the battery cables, positive cable first. 10. Test the auxiliary lamps for proper operation. If necessary, aim the lamps (see AUXILIARYLAMPS, ADJUSTMENT in the Service Manual), and tighten the lamp mounting nuts

Incoming search terms: