YAMAHA R1 OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 28-12-2011

download
The majority of fatalities from motorcycle accidents are the result of head injuries. The use of a safety helmet is the single most critical factor in the prevention or reduction of head injuries. Always wear an approved helmet. Wear a face shield or goggles. Wind in your unprotected eyes could contribute to an impairment of vision that could delay seeing a hazard. The use of a jacket, heavy boots, trousers, gloves, etc., is effective in preventing or reducing abrasions or lacerations. Never wear loose-fitting clothes, otherwise they could catch on the control levers, footrests, or wheels and cause injury or an accident. Never touch the engine or exhaust system during or after operation. They become very hot and can cause burns. Always wear protective clothing that covers your legs, ankles, and feet. A passenger should also observe the above precautions. Modifications Modifications made to this motorcycle not approved by Yamaha, or the removal of original equipment, may render the motorcycle unsafe for use and may cause severe personal injury. Modifications may also make your motorcycle illegal to use. Loading and accessories Adding accessories or cargo to your motorcycle can adversely affect stability and handling if the weight distribution of the motorcycle is changed. To avoid the possibility of an accident, use extreme caution when adding cargo or accessories to your motorcycle. Use extra care when riding a motorcycle that has added cargo or accessories. Here are some general guidelines to follow if loading cargo or adding accessories to your motorcycle

BUELL ACCESSORY GAS CAP KIT INSTALLATION MANUAL

0

Filed Under (Buell) by admin on 29-03-2011

download
Installation NOTE When performing the following Steps, use the Fuel Tank Vent Valve Installation Kit (Part Number 91432-96Y). This kit consists of: * Fuel Tank Vent Valve Installation Aid * Fuel Tank Vent Valve Fitting Socket To protect against shock and accidental start-up of vehicle, disconnect the battery cables, negative cable first, before proceeding. Inadequate safety precautions could result in death or serious injury. Always disconnect the negative battery cable first. If the positive battery cable should contact ground with the negative cable installed, the resulting sparks may cause a battery explosion which could result in death or serious injury. 1. Disconnect battery cables, negative cable first. An open flame or spark may cause a fuel tank explosion if all traces of fuel are not purged from the tank. Use extreme caution when servicing fuel tanks. Gasoline is extremely flammable and highly explosive. Do not smoke or allow open flame or sparks anywhere in the area when working on fuel system components. Inadequate safety precautions could result in death or serious injury. 2. Remove gas cap. 3. Carbureted Models: Drain fuel tank. Disconnect hose clamp and fuel supply hose from fuel supply valve and drain fuel into suitable, clean container. See applicable Service Manual, Section 4 for complete, detailed procedure. Fuel Injected Models: Relieve pressure from fuel system. See applicable Service Manual, Section 4 for complete, detailed procedure. Drain fuel tank. a. Using suitable external fuel pump, such as a Gas Caddy, pump fuel from tank and into a suitable, clean container. b. See instructions for external fuel pump for correct use. 4. See Figure 1. Cut cable tie securing vent hose to fitting and remove vent hose from fuel tank. Even with the fuel tank completely drained, a small amount of gasoline may leak from the bore when the fuel supply valve is loosened or removed. Thoroughly wipe up any fuel immediately and dispose of rags in a suitable manner. Gasoline is extremely flammable and highly explosive. Inadequate safety precautions could result in death or serious injury. 5. If the fuel supply valve requires cleaning or repair, refer to applicable Service Manual, Section 4, for complete, detailed procedures. 6. See Figure 1. Remove the fuel filler cap and O-ring. 7. Remove the eight self-tapping screws from fuel clamp flange and remove fuel cap flange

JMJ-1500 Motorcycle/ ATV Jack OWNER'S MANUAL

0

Filed Under (Tips and Review) by admin on 23-11-2010

download
1. Secure hydraulic ram (20) to the lift base (4) with two screws (21 & 21A). 2. Insert foot pedal assembly (19) into hole over pump piston and secure it with screw (19A) and flat washer (19B). 3. Raise lifting frame (17) to the proper height and align holes in the hydraulic ram (20) with the holes in the middle of the lifting frame. Secure ram to lifting frame with clevis pin (18) and R-pin (22) provided. 4. Place the spring (18A) in position between the clevis pin (18) and screw (18B). Operation 1. Before each use, visually inspect jack for abnormal conditions such as cracked welds, leaks, and damaged, loose or missing parts. 2. To raise the jack, center it directly below object to be lifted. Pump the foot pedal (19) slowly, making sure saddle takes up weight firmly and centrally. Check positioning under slight load to confirm load is centered on jack and load will not shift or slip. 3. Continue to raise jack slowly by pumping foot pedal to reach desired height. 4. Once desired height has been reached, raise safety arms (8) or built-in jack stands, to engage in raised tabs on lift base (4). SLOWLY press pump release foot pedal (23) to allow load to lower and rest on safety arms. 5. Secure load to jack with hold down straps (not included). Fasten hold down straps to steel loops on front and rear of frame. 6. To transport jack under load, lower jack with foot pedal (23) SLOWLY to the lowest position and always use the tow handle (1). Use EXTREME CAUTION when transporting jack under load! 7. To lower jack, raise load slightly with foot pedal (19) and disengage safety arms (8) from lift base (4). Press pump release foot pedal (23) until jack has been completely lowered. Unfasten hold down straps and remove jack from vehicle. Maintenance Adding/Changing Hydraulic Oil: Maintain oil at full level. For best performance and long life, replace hydraulic fluid once a year. 1. With saddle (10) lowered completely, remove oil plug located in hydraulic ram (20). 2. Drain fluid into appropriate container. Always dispose of oil in accordance with local regulations. 3. Use only good quality hydraulic jack oil. Fill until oil is level with inner cylinder as seen from the opening of the filler hole. Reinstall oil plug. Lubricate the jack as indicated on a regular basis with 30W oil. 1. Saddle and linkage on foot pedals and all moving and pivoting parts. 2. Front and rear lifting arms. Always store jack in the fully lowered position. Inspect jack annually for defective parts, missing safety labels or decals. If jack is found to be damaged or defective in any way, or operates abnormally, it shall be removed from service until repaired

Incoming search terms: