2001-2003 EFI Harley Davidson Softail Deuce Power Commander Installation Manual

0

Filed Under (Harley Davidson) by admin on 14-03-2012

download
1 Remove the seat. 2 Remove the two bolts that hold the relay bracket (Fig. A). Fig.A Remove these bolts 3 Fig.B 3 Pull straight upwards on the bracket. Lift the bracket enough to expose the 3 zip ties that hold the wiring harness to the bracket (Fig. B). Cut these 3 zip ties. 4 Pull upwards on the retaining plate (which holds the relays) enough to clear the battery (Fig. C). Fig.C Cut these 3 zip ties 4 9 Fig.D Adjusting Your Power Commander Your Power Commander has been programmed with a base map for your application. You can adjust the base map or install an alternate map using your Computer. Please refer to the supplied CD-Rom for more information. You can also adjust your Power Commander using the face plate buttons as described below. 1. With the ignition off, hold down all three buttons on the Power Commander III unit. 2. While still holding down the buttons, turn the ignition on. 3. Release buttons. 4. Select the range you wish to adjust: Low, Med, High, by pushing the corresponding button once. 5. At this point holding that button down will move the lights down ( leaning out the mixture). 6. Pushing the button repeatedly will move the light up (richening the mixture). 7. When the two center light are lit up this is the “0″ setting. After making your adjustments wait 20 seconds before starting the bike or turning it off. This allows the settings to be saved to memory. To verify that it is safe to start the bike, move the throttle and watch to see if the lights move up and down the scale. If they do, you may start or turn off the bike. Tabs 5 Rotate this plate forward to locate the relay retaining tabs (Fig. D). Bend these tabs so they are flush with the plate. This allows the relays to sit lower in the slots

Incoming search terms:

DST-1200 WHEEL BALANCER INSTALLATION AND OPERATION MANUAL

0

Filed Under (Tips and Review) by admin on 27-11-2010

download
1. Remove the carton from the pallet. 2. Remove the shipping bolts making sure to keep hands clear of all pinch points. 3. Remove straps and plastic wrap holding the hood and tower in shipping position. z Do not use the control tower, face-plate, hood or threaded shaft to lift the balancer. z Use help to remove the balancer from the pallet. The unit is heavy and the weight is not evenly distributed. z Dropping the unit from the pallet may cause personal injury or equipment damage. Electrical Requirements YOUR MACHINE HAS A DUAL VOLTAGE MOTOR and can be run on either 110 or 220 volts. STANDARD WIRING IS 110 VOLTS. Your balancer features a dual voltage, (110/220volt) dual phase (50 or 60 HZ.) power system. Simply position the switch located at the back of the machine to the desired voltage setting then install a required plug if necessary

Incoming search terms:

1999-2001 EFI Harley Davidson Twin Cam 88 Power Commander IIIr Installation Instructions

0

Filed Under (Harley Davidson) by admin on 30-10-2010

download
1 Remove the seat. 2 Remove saddlebags if installed. 3 Remove left and right side covers. 4 Remove the battery (negative terminal first). 5 Loosen the two 7/16 nuts that retain the ECU (Fig. A) 6 From the left side (underneath the left side cover area) feed the PC III connectors in front of battery tray, and out the right side (in front of the ECU bracket)( Fig. B). 7 Attach PC III module to battery box. First, clean the PCII and battery box with the supplied alcohol wipe. Using the supplied velcro attach PCIII to the battery box. Also secure the unit with the included zip ties. If your bike has cruise control, attach the unit to the face of the cruise control module (Fig. C). 8 Disconnect the large connector from the ECU. Remove the rubber dust shield. 9 Install the dust shield onto the matching connector on the PC III. Zip tie the rubber dust shield to the PC III connector with zip tie provided. 10 Plug the PC III connector into the stock ECU. 11 Plug stock connector into the remaining connector fromthe PCIII(Fig. D). 12 Tighten the two 7/16 nuts that retain the ECU. 13 Route the connectors alongside the ECU and install the right side cover. 14 Replace the battery, the left side cover and the seat. 8 5 Adjusting Your Power Commander Your Power Commander has been programmed with a base map for your application. You can adjust the base map or install an alternate map using your Computer. Please refer to the supplied CD-Rom for more information. You can also adjust your Power Commander using the face plate buttons as described below. 1. With the ignition off, hold down all three buttons on the Power Commander II unit. 2. While still holding down the buttons, turn the ignition on. 3. Release buttons. 4. Select the range you wish to adjust: Low, Med, High, by pushing the corresponding button once. 5. At this point holding that button down will move the lights down ( leaning out the mixture). 6. Pushing the button repeatedly will move the light up (richening the mixture). 7. When the two center light are lit up this is the “0″ setting. After making your adjustments wait 20 seconds before starting the bike or turning it off. This allows the settings to be saved to memory. To verify that it is safe to start the bike, move the throttle and watch to see if the lights move up and down the scale. If they do, you may start or turn off the bike

Incoming search terms:

Incoming search terms: