YAMAHA SINGLE SIDED SWINGARM REMOVAL AND INSTALLATION MANUALS

0

Filed Under (Yamaha) by admin on 27-12-2011

download
1. Disconnect Battery 2. Lift and secure bike 3. Remove brake-side floorboard 4. Remove exhaust. 5. Remove rear fender 6. Remove front pulley cover 7. Remove wheel, pulley, and brake assembly simultaneously. Now remove front pulley from transmission. (Keep up with the stock nut and lock washer; these will be used during assembly) 8. Remove Passenger pegs; now remove the plastic covers in the frame that cover the pivot tube bolts. 9. Remove the stock shock bolts ( keep for re-assembly) 10. Remove the pivot tube bolts. 11. Remove the stock swingarmb12. Install “new” belt at this time. 13. Install supplied pivot tube, and bearings in RC swingarm. 14. Install shock bolt with red loctite in RC swingarm. (Do not tighten bolt at this time) 15. Insert supplied pivot bolts with red loctite through frame and supplied bushings into the RC swingarm. (Right side bushing has flats) 16. Torque shock and pivot bolts to factory specs. 17. Install belt adjustment bolts and single side keys into swingarm.

Incoming search terms:

2000-2002 Aprilia Falco INSTALLATION INSTRUCTIONS

0

Filed Under (Aprilia) by admin on 26-10-2010

download
1) It is a good idea to use Blue Loc-tite on all bolts you are about to remove and replace. 2) This kit has extremely close tolerances and in order for all the parts to clear the triple clamp and gas tank, you will probably have to loosen and align most of the associated bolts. We have tried very hard to make this as compact as possible but we know the factory varies quite a bit from bike to bike. Be patient, the results are worth it. 3) Remove the large 14mm Allen nut and washer that holds your triple clamp on. You will not re-use either part. 4) Install the new “Triple clamp damper mount” Part # 22-2919-00 into the recess area where the stock, Allen-head bolt was sitting. There is a machined recess or washer on the bottom of our mount to match the recess on your triple clamp. The 2 knubs that hang downward, should match the rear contour of your triple clamp precisely. Use loc-tite and retighten the 14mm Allen nut, without any washer, to your factory specs, usually a minimum of 35 ft lbs. and a maximum of 85 ft.lbs. 5) Grease the tower pin and drop it in the tower pin hole portion of the frame bracket. The tower pin is designed to “float” and requires no retaining devices. Keep the tower pin lightly greased! 6) Remove both front fuel-tank retaining bolts and washers. You will use the longer bolts provided in our kit. 7) Install the frame bracket (part #22-8636-00) that mounts to your front (2) tank bolts holes. Make sure it does not make contact with the triple clamp. We’ve machined a recess on one side of this bracket to allow for extra clearance (see photo below). The casting ridge on the back of your triple clamp can vary from bike to bike, which might require some slight filing of that ridged seam to avoid contact with our frame bracket. 8) Now check to be sure the tower pin is not abrazing the tank. The tank mounts are adjustable, try to position the tank so nothing is touching. In some rare cases you might have to elongate the rear tank mounting brackets to allow clearance at the front. Use Loc-tite on the longer Allen bolts supplied and tighten the frame bracket 9) Install the stabilizer using the (2) 6×20 Allens with the slot in the link arm matching the tower pin. 10) Since the tank is rubber mounted, you want to be sure it won’t push forward and rub the frame bracket. After riding the first time, be sure the tank has not shoved forward by your body making contact with it. Remember, under heavy braking your entire body weight is pushing the tank forward. Until you have verified sufficient clearance between the tank and the tower pin, it might be smart to put something between the tank and tower pin to protect the tank. 11) Read your damper manual for initial settings on the controls. The damper is infinitely adjustable and totally up to the user to find their preference. Start with softer (counter clockwise) settings. Normally where we set the unit, at 8 clicks out on the base valve, is a good starting point.

Incoming search terms: