2002 Kawasaki 360 ATV WINCH ACCESSORY INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 08-05-2012

download
1. Remove the two 8mm bolts that attach the front bumper assembly to the ATV frame see figure 3. 2. Place Winch mounting plate (A1) into position and fasten the two bent down tabs to the ATV frame using the two 8mm bolts removed in step one, see figure 4, and figure 5. Do not tighten fully at this time. 3. Attach the front of the mounting plate using four 1/4-20 u- bolts (B1), eight lock washers (B2), and eight 1/4-20 hex nuts (B3), see figure 6. 4. Tighten all fastners for the mounting kit at this time. 5. Place winch into position behind the mounting plate. Attach the top two feet of the winch using two 5/16-18 hex cap screws and lock washer. These fasteners will be found in the hardware kit that came with the winch. Note: The winch has floating nuts in its feet. In some instances, a nut may be moved off to one side making it impossible to screw a bolt in. If this becomes the case, take a screwdriver and center the floating nut in the winch to the bolt hole opening. Now attach the bolt through the Winch Plate and into the winch. 6. If using a Cast Hawse Fairlead: It may be neccasary to remove the cast hawse fairlead from the fairlead mounting plate that came with the winch.

Incoming search terms:

Kawasaki ZX-14 Installation And Removal Manual

0

Filed Under (Kawasaki) by admin on 29-04-2012

download
1) Tools needed: 36mm socket / 32mm socket / 5mm Allen wrench / cordless drill / tap handle / hammer / razor blade. 2) The frame bracket serves as the drilling guide and we provide the transfer punch, tap, drill and step by step instructions for a relatively easy installation. However, do not attempt this installation unless you are skilled enough and confident that you can drill and tap (2) holes in your frame. We’ve also provided a picture of what it will look like should you decide to sell this bike later on, with your stabilizer removed. Follow these guidelines and you’ll find it’s quite easy. 3) Some photos may not be your exact bike but depict the idea of what needs to be done. 4) It is important to use Blue Loc-tite on all fasteners if you expect them to stay tight. 5) Cover the gas tank area with something substantial to protect the paint, in case of a slip. An old sweatshirt works well. It’s cheap insurance to actually just remove the tank shroud to avoid an accident. 6) Remove the stock 36mm nut AND washer , that holds the top triple clamp tight. Make a note of how tight it is. 7) Install the new “triple clamp damper mount” (TC mount) over the steering stem allowing it to match the exact shape of the triple clamp, with the “machined register” (lip) indexing over the back of the triple clamp. (See photo). 8) Install the new 32mm aluminum nut supplied in the kit (without any washer) with the Hex drive facing up and torque to 65ft. lbs. or more. (Check your manual for the recommended torque setting of this nut). 9) There is a slight amount of play in the “register” that fits over the back of the triple clamp to allow for variations in castings from the factory. If the TC mount tries to spin clockwise during tightening, which can misalign the stabilizer ever so slightly, you can slide something thin, like the edge of a razor blade, between the register and the back of the triple clamp to space it “just right” for alignment during tightening (see photo). Once it’s tight the razor blade will be stuck, so gently turn the 32mm socket as though you were going to loosen the nut but don’t actually loosen it. It will relieve enough pressure to allow the razor blade to come out. Double check your alignment again. 10) Remove the front tank mounting Allen bolt. Retain the stock washer that’s part of the rubber grommet. 11) Temporarily install the frame bracket and be sure the outer feet are touching or are very close to the frame. On rare occasions, the casting on the head tube prevents the feet from making contact. On these rare occasions you may have to slightly file the inner side of those feet until the bracket sits down flush. Not sure on this one? Call us. (note: 2007-on bikes have a larger casting area and early kits will not fit these late model bikes. All current kits now fit 2006-on)

HARLEY-DAVIDSON SPRINGER FORKS MOUNTING INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-04-2012

download
1. The shock mounts with the body up —shaft pointing down. The nitrogen fill valve can be positioned toward the rear of the motorcycle. 2. Make sure that both halves of the upper and lower bushings are in place. NOTE: Do not try to install the shock with only half of the bushings, as this will lead to poor performance and premature seal leakage. The amount of “float” in the bushing set is necessary to ensure smooth operation of the damper assembly. 3. It is easiest to install the shock when the forks are fully extended, however the shock can be installed with the bike on the kick stand. 4. Insert the body eye into the mounting channel on the fork crown. Rotate the shock down into the lower channel. NOTE: A thread locking compound such as Red Loctite 262 or other similar product should be used on the shock fasteners. 5. Install the upper mounting stud and nuts, finger tight. 6. Push the shaft up far enough to insert the lower mounting stud and nuts. This will take a little effort because of the gas pressure in the shock. 7. Torque the upper and lower shock mount nuts to 22 ft. lb.

2001-2008 Suzuki V-Strom DL650 And DL1000 Adapter Installation Manual

0

Filed Under (Suzuki) by admin on 15-02-2012

download
Adapter Parts List Item Desc. Quantity A. Front Adapter 1 B. Rear Adapter 1 C. Frame Grabber, Front 2 D. Frame Grabber 1 E. 5/16 x ½” Button Head Screws 4 F. M8 x 50mm Bolts 2 G. Washers (Not shown) 6 2. Assembly Instructions Familiarize yourself with all of the parts in the Main Arm and Motorcycle Adapter assemblies. Follow these installation instructions FIRST . The following instructions include our recommended torque values for all fasteners used to assemble the Johnny Rack™. Do not exceed those torque values when installing the rack, otherwise damage to the Main Arm may occur. When stock mounting points are used to mount the rack to the motorcycle, refer to the motorcycle user’s manual for recommended torque values. 1. Remove the seat, the rubber rack cover on the rear rack or if you have a Givi Top Case mounting plate remove it too. Remove the 4 bolts shown (A and B). 2. Align front frame grabbers over front grab bar mounting holes (A). 3. Reinstall original bolts that you removed. Torque to 150in.lbs. 4. Place rear frame grabber over holes on rear rack (B). 5. If you do not have side luggage racks installed on the motorcycle, you will need to place 3 stacked washers (3/4 ” OD) over each hole and under the frame grabber to take up the extra space.

Honda TRX 450R 2006 Rear Grab Bar INSTALLATION AND REMOVAL INSTRUCTIONS

0

Filed Under (Honda) by admin on 23-12-2011

download
To avoid injury or damage to your ATV, read these instructions before installation. 1. Parts List: Item Part Name Description Qty 1 H062060 Grab Bar 1 2. Preparation: a) Lock rear brake on bike. b) Remove OE grab bar, retaining all mounting hardware. c) Remove 3 OE rubber grommets from OE grab bar. 3. Installation: a) Install 3 rubber grommets on Pro Race Grab Bar.. b) Install Pro Race Grab Bar on bike, reusing all hardware and mounting locations. 4. Maintenance: Check fasteners for tightness and re-torque as required. 5. Care and Cleaning: Clean using mild soap. 6. Customer service: For further information call Pro Armor at 951-270-0559

Honda VT1100C Shadow, Aero, Sabre SPECIFIC-FIT SADDLEBAGS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 23-04-2011

download
The saddlebag supports are hinged 3 so they can adjust to any variance in your motorcycle’s fender strut bolt locations. The supports have a one-inch offset 4 that angles the supports outward so they space the bags away from the motorcycle’s chassis components, wheels, brakes, and moving parts. Before removing or changing any hardware, hold the supports next to the motorcycle to familiarize yourself with how they will be installed. Remove the original fender mounting bolts from one side of the fender strut and temporarily mount one support with a 10mm bolt, a plastic and steel spacer, and two washers into the front fender stay bolt hole. Then insert an 8mm bolt, a plastic and steel spacer, and two washers into the rear fender stay bolt hole. Verify that each bolt is the proper length. IMPORTANT: The VT1100 Shadow Classic, Aero, or Sabre models have 10mm (front) and 8mm (rear) threaded holes in the fender strut. Use care to not insert the wrong size mounting bolt in the strut. When installing a bolt into the fender strut, check to be sure that it does not extend inside the fender further than the original fasteners. If it does, the excess length of the bolt must be cut off, or exchanged for a shorter bolt you obtain from the hardware store or a motorcycle shop. After verifying the mounting bolts are the proper length, remove the support from the motorcycle’s fender strut. Install a grommet in each of the large holes 5 on the back side of each saddlebag. Then insert a plastic spacer 6 in each of the grommets TIP: Use soapy water to lubricate the grommets so they will slip into the holes in the bag. The vehicle images in this instruction set may be different than your motorcycle. Continued on next page… 3 Lay a support 7 (with the joint towards the rear of the bag) on the back of a bag. Temporarily put the mounting bolts 8 through the support’s holes and into the plas- tic spacers in the grommets. Place one of the support clips 9 over the center of the lower portion of the support, so the two holes in the clip align with the predrilled holes in the bag. Use the 3/16” screws and nuts from the hardware kit to attach the support clip to the backup plate inside the bag. Place the nuts on the outside of the bag. Do not over- tighten the hardware, as this may cause damage to the saddlebag. Remove the mounting bolts from the support and the plastic spacers

Incoming search terms:

HARLEY DAVIDSON ROAD KING CLASSIC FRONT FENDER SKIRT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-04-2011

download
INSTALLATION 1. Remove fasteners from stock fender skirt. NOTE Some early models have rivets for fasteners. These rivets will need to be drilled out. Drill the rivet heads to a sufficient depth to remove the head from the rivet shaft. Do not attempt to drill the rivet all the way through. This may scratch the fender?s painted surface. 2. Remove stock fender skirt. 3. Thoroughly clean the fender under the skirt. At this point it may be a good idea to wax this portion of the fender to prevent rust in the future. 4. See Figure 1. Cut the adhesive foam strip (5) into three equal parts. Remove the backing from the adhesive strips and apply adhesive on middle and two sides at the inside/bottom of the fender skirt (1). The foam strips will prevent rattling and unwanted noise. NOTE On some later FLT models, there may not be enough fender skirt support to allow the application of adhesive strips. If this is true for your motorcycle, you may install this kit without the adhesive strips. 5. Place the fender skirt in position, aligning fastener holes. 6. Install the screws (2) from the outside of the fender. Install the washers (4) and nuts (3) inside the fender. 3 2 4 1 5 is03865 1. Fender skirt 2. Screws 3. Locknuts 4. Washers 5. Adhesive foam strip Figure 1. Front Fender Skirt and Hardware

HARLEY DAVIDSON REAR SADDLEBAG GUARDRAILS INSTALLATION MANUAL

0

Filed Under (Harley Davidson, Uncategorized) by admin on 18-04-2011

download
Installation KITNUMBER 49087-01 1. Remove and save fasteners that retain saddlebag guardrails. 2. Replace stock saddlebag guardrails with new guardrails from kit. 3. Screw in and torque each stock fastener as follows: a. Four stock screws, Part No. 3678, using two new locknuts (1), Part No. 7667. Torque each screw to 19 ft-lbs. b. Two stock screws, Part No. 3601 using two new locknuts (2), Part No.7686. Torque each screw to 9 ft-lbs. For Domestic FLHRC/I Vehicles Only. (Does not apply to Harley Davidson International (HDI) vehicles): Federal Motor Vehicle Safety Standard (FMVSS) 108 requires all motorcycles to be equipped with side reflectors. Install, or have Dealer install, the reflectors, Part Nos. 59370-98 and 59371-98, which are purchased separately. Loss of visibility to other motorists could result in death or serious injury. 1. See Service Parts illustration. Position reflector so it is centered on the vertical portion of the saddlebag guard 1″ above the top end of the lower bend where the radius turns upward. Measure and use a small piece of tape to mark location for attachment of the lower edge of the reflector at the 1″ mark. 2. Remove protective tape backing from one reflector. Locate reflector above the 1″ mark. Apply reflector, using even pressure by rubbing back and forth on reflector. Repeat for other side. Note Reflectors are specific for each side. Reflectors have a flat end and a curved end. The curved end goes down. Top edge should be horizontal when positioned on guard. If not, reflector is for opposite side. KITNUMBER 49088-01 1. Remove and save fasteners that retain saddlebag guardrails. 2. Replace stock saddlebag guardrails with new guardrails from kit. 3. Using four hexsocket button head screws (4) removed earlier, attach saddlebag guards using the remaining two existing holes in each guardrail. 4. Screw in and torque each stock fastener as follows: a. Four stock screws, Part No. 3678, using two new locknuts (1), Part No. 7667. Torque each screw to 19 ft-lbs. b. Two stock screws, Part No. 3601 using two new locknuts (2), Part No.7686. Torque each screw to 9 ft-lbs

Incoming search terms:

HARLEY DAVIDSON FLSTC SOFTAIL SADDLEBAG KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 16-04-2011

download
Additional Fitment Information Detachables NOTE If motorcycle has not been altered from fixed saddlebag hardware to accessory mounting detachable docking points. the separate purchase of Turn Signal Mounting Bar (Part Number 68611-98) is required for sufficient lock clearance. This kit is available at your Harley-Davidson Dealer. Installing these saddlebags on models equipped with a detachable sissy bar or detachable luggage rack requires the additional purchase of mounting hardware kit as follows: Hardware Kit Fitment 53075-03 2003 and later FLSTC models with detachables 53009-03 1987 through 2002 FLSTC models with detachables See Service Parts Page for kit contents. Additional weight can affect motorcycle stability, handling characteristics, and safe operating speed. Do not exceed 7 lbs. (3.18Kg) maximum load in each saddlebag. Evenly distribute weight between each saddlebag. Improper loading can cause vehicle handling problems leading to death or serious injury. Wide Tire If a wide tire kit has been installed, utilize the hardware and installation instructions found in that kit to reorient the fasteners to come from the inside to the outside of the finder. Button head screws from wide tire kit must be installed from the inside out, with the button heads on the inside of the fender. Failure to do so could result in bolt contacting tire, which could result in death or serious injury. Installation NOTE A Service Manual for your vehicle is available at your Harley-Davidson Dealer. 1. Remove seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. (00048a) Disconnect the negative (-) battery cable first. If positive (+) cable should contact ground with the negative (-) cable connected, the resulting sparks may cause a battery explosion which could result in death or serious injury. (00049a) 2. Disconnect battery cables, negative cable first. 3. Following instructions in applicable Service Manual, remove original saddlebags from supports. Install Turn Signal Mounting Bar If motorcycle is not equipped with accessory mounting detachable docking points, install Turn Signal Mounting Bar (Part No. 68611-98) following instructions provided with the kit. See Figure 1

Incoming search terms:

HARLEY DAVIDSON SOFTAIL CHROME LOWER BELT GUARD INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-04-2011

download
REMOVING STOCK PLASTIC LOWER BELT GUARD 1. See Figure 1. Remove the hex head bolt (2), washer (3), acorn nut (5), hex head screw (4) and acorn bolt (8) attaching plastic belt guard to rear fork. 2. Remove the plastic belt guard. Save fasteners (2), and (4), washer (3), acorn nut (5) and acorn bolt (8) for installing new chrome belt guard. INSTALLING CHROME LOWER BELT GUARD 1. See Figure 2. Position the new chrome belt guard from kit over belt. Align the holes in guard with mounting lugs on rear fork. Install acorn bolt (9) through mounting lug and fasten to belt guard. Finger tighten only. 2. Install screw (4) with washer (5, from kit) through belt guard and fasten to threaded mounting lug. Position the guard for adequate clearance and finger tighten screw. 3. At the upper belt guard, install the original forward hex bolt (2) and original washer (3) through the upper guard (1), then through the upper hole in chrome belt guard and through mounting lug on rear fork. Secure with original acorn nut. 4. Tighten all hardware to 110 in-lbs (12.4 Nm)

Incoming search terms:

Incoming search terms: