HARLEY DAVIDSON REAR SADDLEBAG GUARDRAILS INSTALLATION MANUAL

0

Filed Under (Harley Davidson, Uncategorized) by admin on 18-04-2011

download
Installation KITNUMBER 49087-01 1. Remove and save fasteners that retain saddlebag guardrails. 2. Replace stock saddlebag guardrails with new guardrails from kit. 3. Screw in and torque each stock fastener as follows: a. Four stock screws, Part No. 3678, using two new locknuts (1), Part No. 7667. Torque each screw to 19 ft-lbs. b. Two stock screws, Part No. 3601 using two new locknuts (2), Part No.7686. Torque each screw to 9 ft-lbs. For Domestic FLHRC/I Vehicles Only. (Does not apply to Harley Davidson International (HDI) vehicles): Federal Motor Vehicle Safety Standard (FMVSS) 108 requires all motorcycles to be equipped with side reflectors. Install, or have Dealer install, the reflectors, Part Nos. 59370-98 and 59371-98, which are purchased separately. Loss of visibility to other motorists could result in death or serious injury. 1. See Service Parts illustration. Position reflector so it is centered on the vertical portion of the saddlebag guard 1″ above the top end of the lower bend where the radius turns upward. Measure and use a small piece of tape to mark location for attachment of the lower edge of the reflector at the 1″ mark. 2. Remove protective tape backing from one reflector. Locate reflector above the 1″ mark. Apply reflector, using even pressure by rubbing back and forth on reflector. Repeat for other side. Note Reflectors are specific for each side. Reflectors have a flat end and a curved end. The curved end goes down. Top edge should be horizontal when positioned on guard. If not, reflector is for opposite side. KITNUMBER 49088-01 1. Remove and save fasteners that retain saddlebag guardrails. 2. Replace stock saddlebag guardrails with new guardrails from kit. 3. Using four hexsocket button head screws (4) removed earlier, attach saddlebag guards using the remaining two existing holes in each guardrail. 4. Screw in and torque each stock fastener as follows: a. Four stock screws, Part No. 3678, using two new locknuts (1), Part No. 7667. Torque each screw to 19 ft-lbs. b. Two stock screws, Part No. 3601 using two new locknuts (2), Part No.7686. Torque each screw to 9 ft-lbs

Incoming search terms:

HARLEY DAVIDSON SPLASH SHIELD KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
This kit is designed to fit 1980 – 1983 and 1988 and later FLHT and 1994 and later FLHR models without fairing low- ers. installation 1. Locate splash shield for left side. Bar and Shield should face forward and opening in splash shield should be on right side. 2. Slip splash shield on left side of engine guard. 3. An opening in the outer edge of the splash shield allows the splash shield to fit over highway footrests. 4. Place the wide attaching strap around the frame down- tube, do not put strap over clutch cable. 5. Slip buckles on attaching strap onto mating buckle halves attached to back side of splash shield. Latches will snap into locked position when buckle is properly closed. 6. Adjust the fit by lifting the Velcro┬«attached straps (on rear of splash shield) and changing length as required. 7. Repeat procedure for right side of vehicle. NOTE If splash shields cover amber reflectors mounted on frame down tubes, install reflectors included in kit as follows: 8. See Figure 1. Clean areas on both sides of fender (1) where amber reflectors are to be mounted. 9. Remove backing paper from rear of reflector and place reflectors in position (2). Federal Motor Vehicle Safety Standard (FMVSS) 108 requires motorcycles to be equipped with rear and side reflectors. Be sure rear and side reflectors are properly mounted. Low visibility of rider can result in death or serious injury. (00336a) NOTE To remove splash shields depress both latches with thumb and forefinger and gently pull buckle apart. Open remaining buckle and slide splash shield off engine guard

Incoming search terms:

HARLEY DAVIDSON SPORTSTER LEATHER SADDLEBAG KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
SADDLEBAG INSTALLATION 1. See Figure 3. Remove the rear shock absorber bolt (Figure 1, Item 1). Position the 0.531 x 0.75 x 0.25 inch spacer (7) and the front saddlebag bracket attachment hole over the rear shock absorber bolt location. Secure with the 1/2- 13 x 3.75 inch screw (5). 2. See Figure 3. Position the 0.325 x 0.75 x 0.25 inch spacer (8) and the rear saddlebag attachment hole over the second hole on the rear of the fender, fender support cover, and relocation pad. From the underside of the fender, insert a 5/16-18 x 3.00 inch screw (6) and secure with locknut (10). Tighten locknut (10) to 24-27 ft-lbs (32.5-36.6 Nm) . 3. Tighten the front screw (5) to 21-27 ft-lbs (28.5-36.6 Nm) . 4. See Figure 3. Assemble an isolator washer (12) onto an isolator bushing (13). Place a screw (15) through the bushing. 5. Place the screw and bushing assembly into the top hole inside the saddlebag back. 6. See Figure 3. Push a saddlebag isolator (14) over bushing with cone shape toward saddlebag. 7. Place saddlebag in position on bracket and insert the new screw (15) into the bracket. Do not tighten. 8. Repeat steps 4 through 7 for remaining holes. With all isolators in place, tighten screws to 96-120 in-lbs (10.8- 13.6 Nm) . 9. Repeat Steps 1 through 8 for the opposite saddlebag. 10. Raise rear wheel until the rear shock absorbers align with shock absorber mounting holes on the swingarm. Support the wheel to prevent it from falling during the following step. 11. See Figure 1. Attach rear shock absorber to swingarm by installing bolt (1), washer (2) and nut (4). Tighten bolt to 45-50 ft-lbs (61.1-67.9 Nm) . Repeat step on opposite side of motorcycle. INSTALL REFLECTORS Federal Motor Vehicle Safety Standard (FMVSS) 108 requires motorcycles to be equipped with rear and side reflectors. Be sure rear and side reflectors are properly mounted. Poor visibility of rider to other motorists can result in death or serious injury. (00336b) 1. See Figure 3. Measure approximately 1-1/2 in. (38 mm) from the bottom edge of the saddlebag. Orient the reflector horizontally and carefully center the reflector mount between the straps of bags with straps or locate it at the rearward portion of bags without straps. Mark hole location. 2. Using appropriate tool, make two 3/16 in. holes in sad- dlebag. 3. Install reflector mount (3) on saddlebag using two pushnuts (2). 4. Remove adhesive backing from reflector (4) and install on mount. 5. Repeat steps 1 through 4 for the opposite saddlebag. INSTALL SEAT After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 1. See Service Manual instruction to install the seat

Incoming search terms: