HARLEY DAVIDSON HERITAGE CHROME FRONT FENDER RAIL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
INSTALLATION NOTE See Figure 1. Be careful not to crack plastic fender lamp lens (2) or chrome plate when removing lens. 1. Remove fender lamp light lens (2) by placing screwdriver in slot in top of lens and carefully prying cover loose. Retain lens and gasket for later installation. 2. Loosen four hex socket head screws (1) which attach fender (4) to fender mount. 3 2 4 1 is03805 1. Fender mount screws (4) 2. Fender lamp light lens 3. Fender Rail 4. Fender Figure 1. Installed Front fender Rail NOTE When installing fender rail (3), be sure fender rail supports are inside of fender. 3. Place fender rail (3) from kit into position, aligning the front bracket hole of rail with hole in front of fender (4). Fender rail supports will fit snugly inside fender. NOTE Be careful not to damage the fender lamp wire when securing front fender rail into place. 4. Use a magnet to place a 10-32 x 1/2 inch phillips screw through the hole in front fender and through front bracket hole of fender rail (3). 5. Loosely secure fender rail (3) to fender (4) with 1/2 inch flat washer and hex locknut. 6. On right side only, remove two hex socket head screws and nuts. Retain nuts for installation. 7. Replace original two socket head screws with 5/16-18 x 2 inch screws from kit. 8. For vehicles without caliper/rotor covers: On left side of fender (4) only, install a washer between rail (3) and fender for both screws. Replace original two hex socket head screws with 5/16-18 x 2 inch screws from kit. For vehicle with caliper/rotor covers: Do not replace hex socket head screw that supports caliper/rotor cover. On left side of fender (4), install a washer between fender (4) and rail (3) on screw that does not support the caliper/rotor cover (towards the front of the vehicle). Replace remaining hex socket head screw with 5/16-18 x 2 inch screw from kit. 9. Install four original nuts. 10. Tighten front bracket Phillips screw securely. Tighten four hex socket head screws to 14-18 ft-lbs (19-24 Nm). 11. Install gasket and fender lamp lens removed earlier

Incoming search terms:

HARLEY DAVIDSON HERITAGE REAR FENDER RAIL DISASSEMBLY AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-02-2011

download
DISASSEMBLY NOTE See Figure 1. Saddlebags must be removed to insert spacer (1). 1. Using a small flat head screw driver, remove rear fender tip light lens cover (A) by gently prying cover away from assembly. (There is a notch at top of cover to ease removal.) Remove and retain cover (A) and gasket (C). 2. Remove fender tip light assembly (B) by removing two screws, four star washers, and two nuts (not shown) using a #2 Phillips screw driver and a 3/8 inch wrench. Retain all hardware for reassembly. 3. Remove hole plugs from rearmost fender strut holes on both sides of fender. 4. Mark fender on both sides of bike using rear most fender strut hole as a template. Do not contact tire with drill bit when drilling fender holes. Drill bit contact with tire can lead to premature tire failure, which could result in death or serious injury. (00403f) 5. Carefully remove fender strut and drill a 11/32 inch hole through each side of fender in locations marked in Step 4. 6. Loosely reinstall fender strut (D), allowing enough room to slip spacer (1) between fender (E) and strut. INSTALLATION 1. Align rear fender rail (2) from kit with rearmost fender strut (D) mounting holes, making sure lower mounting tab (3) is inside fender (E). Place large chrome washer (4) from kit next to head of button head socket bolts (5) from kit. Insert bolt through fender rail (2), fender strut (D), spacer (1) and fender (E), in that order. Install large unfinished washer (6) from kit onto end of bolt (5). Secure assembly into place by threading locknuts (7) from kit onto ends of bolts (5) from inside of fender (E). Tighten loosely at this time. 2. Install truss head screw (8) from kit through fender (E) and rear fender rail mounting tab (3). Secure into place using small washer (9) and locknut (10) from kit. Use #2 Phillips screwdriver and a 3/8 inch wrench to tighten rear mounting assembly securely. 3. Tighten fender strut bolts (5) to 21-27 ft-lbs.(28-37 Nm) 4. Reinstall fender tip light assembly (B), gasket (C) and lens (A) using original hardware (not shown)

Incoming search terms:

HARLEY DAVIDSON V-LOGO REAR FENDER TRIM RAIL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-02-2011

download
INSTALLATION NOTE All models for which this kit is designed are equipped with a original equipment (stock) fender rail or bumper. Remove the stock bumper and install the kit rail using following the proce- dures. 1. See Figure 1 and Table 1. Install V-logo (4) to trim rail (1) with hex washer screws (3) and lock washers (2). 2. Reach under rear edge of fender and remove locknut (A) and washer (B). Retain locknut and washer and use to mount new trim rail. 3. Loosen and remove the two screws (C) and locknuts (D) which attach fender rail to saddlebag support bracket. Retain screws (C) and locknuts (D) and use to mount new trim rail. 4. Place new trim rail in position and install washer (B), locknut (A), screws (C) and locknuts (D). 5. Tighten locknut (A) to 45-85 in-lbs (5.0-9.6 Nm) and locknuts (D) to 15-20 ft-lbs (20.3-27.1 Nm) . SERVICE PARTS 2 3 4 1 A B C D is05379 Figure 1. Service Parts: V-Logo Rear Fender Rail Table 1. Service Parts Part Number Description (Quantity) Item Not Sold Separately Trim rail, rear fender 1 7115 Lock washer (2) 2 7611 Hex washer screw (2) 3 91112-94 V-logo 4 Items mentioned in text, but not included in kit. Locknut (2) A Washer (2) B Screw (2) C Locknut (2)

SUZUKI VOLUSIA 800, C50, M50 Left/ Right Saddlebag Installation Manual

0

Filed Under (Suzuki) by admin on 14-11-2010

download
Your saddlebag supports will install in just a few minutes using common tools. Read all instructions carefully and completely before installing your new saddlebag supports. 1. Remove your stock fender rail bolts. 2. Install your Cobra saddlebag supports using the supplied 8mm x 65mm button head bolts (where the stock bolts were removed), the saddlebags should hang towards the rear and away from the motorcycle. 3. Torque bolts to factory specifications Cobra recommends you always wear a helmet while riding. Please never operate your motorcycle while under the influence of alcohol and/or drugs. Enjoy the new look of your motorcycle and please ride safely

Incoming search terms:

Honda VTX1800C Plated Saddle Bag Installation Manual

0

Filed Under (Honda) by admin on 14-11-2010

download
Instruction Manual > Your saddlebag supports will install in just a few minutes using common tools. Read all instructions carefully and completely before installing your new saddlebag supports. 1. Remove your stock fender rail bolts. 2. Place the supplied spacers in the recessed holes on the fender rails (large spacer to the front, small spacer to the rear). 3. Install your Cobra saddlebag supports using the supplied button head bolts (where the stock bolts were removed) the saddlebag supports should hang towards the rear and away from the motorcycle. 4. Torque bolts to factory specifications. Note: If using Cobra sissy bar mount the saddlebag supports over the sissy bar brackets and do not use supplied spacers. Cobra recommends you always wear a helmet while riding. Please never operate your motorcycle while under the influence of alcohol and/or drugs. Enjoy the new look of your motorcycle and please ride safely.

Ridley Auto-Glide Installation Manual

0

Filed Under (Ridley) by admin on 01-11-2010

download
Place motorcycle in a secure upright position 2) Remove saddle bags (if applicable) 3) Remove rear fender mounting bolts (3 each side) 4) Tap indicated rear fender mounting holes with a 3/8″ – 16 tap. (2 holes each side) It is highly recommended that cutting/tap oil is used. Use care when tapping holes. Be certain to tap holes completely through. 5) Ensure 2 large attachment bolts are tight. 6) Attach Bracket C (left) and Bracket D (right) to rear fender rail. Use new bolts provided on outer tapped holes (2) and one of the longer original bolts for center hole. Place one washer between brackets C & D and rear fender rail on each bolt. (3 each side) Place washer and thin nut on inside of rear fender on new bolts (2 each side) These replace original fender washers. It may be necessary to reattach saddle bag attachment hardware when attaching brackets C and D. All saddle bag hardware should be attached to the OUTSIDE of brackets C and D. 7) Attach front of Bracket A (left) and B (right) to existing hole in motorcycle frame just above swing arm pivot. 8) Attach rear of bracket A (left) B (right) to TOP of forward hitch arms. Snug bracket A and B attachment bolts at this time. 10) Attach top of Bracket E (left) and F (right) to outside of lower tabs on bracket C & D. 11) Attach bottom of brackets E and F to top of rear hitch plate. 12) Tighten bolts at this time. Use caution not to over tighten and strip tapped holes in rear fender rail. Bracket Identification

Incoming search terms: