HARLEY DAVIDSON V-LOGO REAR FENDER TRIM RAIL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-02-2011

download
INSTALLATION NOTE All models for which this kit is designed are equipped with a original equipment (stock) fender rail or bumper. Remove the stock bumper and install the kit rail using following the proce- dures. 1. See Figure 1 and Table 1. Install V-logo (4) to trim rail (1) with hex washer screws (3) and lock washers (2). 2. Reach under rear edge of fender and remove locknut (A) and washer (B). Retain locknut and washer and use to mount new trim rail. 3. Loosen and remove the two screws (C) and locknuts (D) which attach fender rail to saddlebag support bracket. Retain screws (C) and locknuts (D) and use to mount new trim rail. 4. Place new trim rail in position and install washer (B), locknut (A), screws (C) and locknuts (D). 5. Tighten locknut (A) to 45-85 in-lbs (5.0-9.6 Nm) and locknuts (D) to 15-20 ft-lbs (20.3-27.1 Nm) . SERVICE PARTS 2 3 4 1 A B C D is05379 Figure 1. Service Parts: V-Logo Rear Fender Rail Table 1. Service Parts Part Number Description (Quantity) Item Not Sold Separately Trim rail, rear fender 1 7115 Lock washer (2) 2 7611 Hex washer screw (2) 3 91112-94 V-logo 4 Items mentioned in text, but not included in kit. Locknut (2) A Washer (2) B Screw (2) C Locknut (2)

HARLEY DAVIDSON AM/FM ANTENNA RELOCATION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the Owner’s Manual and follow the instructions given to remove the left-side saddlebag. Gently pull the left-side cover from the frame downtubes (no tools are required), and remove the main fuse. 2. See Figure 1. Disconnect the antenna cable from the antenna base assembly (1). 3. Unscrew the antenna mast (2) from the antenna base, and set it aside for later installation. 4. Remove the lower locknut (3), and remove the antenna base from the mounting bracket (5). Save both locknuts, but discard the lockwasher (4). 5. Remove the two TORX® head screws (6) and lockwashers (7) retaining the antenna mounting bracket to the saddlebag rear support bracket (8). Discard the bracket and fasteners. 6. Carefully remove and discard any cable straps securing the antenna cable to the fender support and saddlebag rear support brackets. 8 9 6 3 2 5 7 4 3 1 is05436 1. Antenna base assembly 2. Antenna mast 3. Locknut (2) 4. Lockwasher 5. Original antenna mounting bracket 6. TORX head screw (2) 7. Split lockwasher (2) 8. Saddlebag rear support bracket 9. TORX Pan head screw and flanged locknut Figure 1. Original Antenna Mount 7. Remove and discard the TORX head screw and nut (9) that fastens the lower saddlebag support bar to the rear fender support bracket. 8. See Figure 2. Obtain the new antenna bracket (1), button head screw (2), flat washers (3 and 4) and flange nut (5) from the kit. NOTE If V-Logo Rear Fender Trim Rail Kit 91100-09 has been installed, the thick washer (4) is not used, and can be dis- carded.

Incoming search terms:

HARLEY DAVIDSON FLSTF FENDER TRIM INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
INSTALLATION 1. Thoroughly clean the fender tip in the area where the trim will be mounted. 2. Cover the fender with masking tape to protect the painted surface during positioning of the trim. 3. Place the trim in the desired location and hold it in position. Mark the hole locations with a felt tip pen or pencil. Remove the trim. 4. Carefully center punch the hole locations in the fender. 5. Drill the mounting holes using a 1/8 in. (3 mm) diameter drill bit. 6. Remove the masking tape from the fender. 7. Mount the trim on the fender using the screws and lock nuts provided in the kit