HARLEY DAVIDSON SPLASH SHIELD KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
This kit is designed to fit 1980 – 1983 and 1988 and later FLHT and 1994 and later FLHR models without fairing low- ers. installation 1. Locate splash shield for left side. Bar and Shield should face forward and opening in splash shield should be on right side. 2. Slip splash shield on left side of engine guard. 3. An opening in the outer edge of the splash shield allows the splash shield to fit over highway footrests. 4. Place the wide attaching strap around the frame down- tube, do not put strap over clutch cable. 5. Slip buckles on attaching strap onto mating buckle halves attached to back side of splash shield. Latches will snap into locked position when buckle is properly closed. 6. Adjust the fit by lifting the Velcro®attached straps (on rear of splash shield) and changing length as required. 7. Repeat procedure for right side of vehicle. NOTE If splash shields cover amber reflectors mounted on frame down tubes, install reflectors included in kit as follows: 8. See Figure 1. Clean areas on both sides of fender (1) where amber reflectors are to be mounted. 9. Remove backing paper from rear of reflector and place reflectors in position (2). Federal Motor Vehicle Safety Standard (FMVSS) 108 requires motorcycles to be equipped with rear and side reflectors. Be sure rear and side reflectors are properly mounted. Low visibility of rider can result in death or serious injury. (00336a) NOTE To remove splash shields depress both latches with thumb and forefinger and gently pull buckle apart. Open remaining buckle and slide splash shield off engine guard

HARLEY DAVIDSON BLADE FRONT WHEEL KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2011

download
INSTALLATION 1. Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. or FXSTD: Discard tapered spacer. NOTE Install short valve stem (43157-83A) included in the installation kit. Discard all other valve stems. 2. See Figure 2. Install valve stem assembly (L) on wheel. Refer to TIRES in service manual. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. The side with the machined groove on the hub face is the primary bearing side for all kits except Kits 41681-07 and 40818-08. For Kit 41681-07: Install the wheel so that the hub markings are on the left side and the machined groove is on the right side of the motorcycle. • For 2006 and later FXDWG Models: When correctly installed, the tire will be 0.08-0.2 in (2-5 mm) off of center, compared to the fender. • For 2007 and later FX Softail and 2008 and later FXDWG Models: The left side of the wheel is the primary bearing side. • For 2006 and earlier FX Softail and 2007 and earlier FXDWG Models: The right side of the wheel is the primary bearing side. For Kit 40818-08: • Proper installation of this kit requires the separate purchase of two floating brake discs (44343-01 for 2004 – 2007 models and 44553-06A (stock) or 41500012 (polished) for 2008 and later models) and a tire (43371-07 on 2004-2008 models and 44026-09A on 2009-later models). The left side of the wheel has machined DOT markings to identify it as the primary bearing side. • For 2008 and later Touring: Install bearing shim (43903- 08) under the primary bearing. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in service manual. 4. For FLSTC and FLSTN Models: Install wheel kit and right hand wheel spacer provided in installation kit. Refer to FRONT WHEEL in service manual. For FXSTD Models: Install wheel kit, stock wheel spacer and right side wheel spacer provided in installation kit in place of the tapered spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install wheel kit, stock wheel spacers and spacer provided in installation kit between the left side wheel spacer and the left fork. For all other models: Install previously removed wheel spacers. Refer to FRONT WHEEL in service manual. 5. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly to verify that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant

Incoming search terms:

HARLEY DAVIDSON SOFTAIL CUSTOM SEAT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
Kit Contents See Figure 3 and Table 2 for complete kit contents. See Table 1 for the grab strap part number associated with each seat kit. Table 1. Kit Numbers and Grab Strap Usage Grab Strap Kit Number 51332-07 51310-07 51910-08 51936-08 51701-06 51308-07 51365-07 51367-07 51387-06A 51388-06 51389-06 51390-06 51391-06 51392-06 51398-07 51365-07 51410-08 51411-08 51412-08 51414-08 51415-08 51416-08 51407-08 The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley- Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308a) INSTALLATION NOTE When performing the following procedures, avoid scratching painted surfaces (fender, tank, etc.) with tools or metal seat tabs. FXST, FXSTB and FXSTS Models 1. See Figure 3 and Table 2. Unscrew the captive thumbscrew fastening the back of the original equipment (OE) seat to the vehicle. 2. Pull the seat slightly to the rear to disengage the tang at the front of the seat from the motorcycle frame. 3. Lift the front of the seat while pulling the seat carefully forward to remove the seat from the vehicle. 4. Remove the OE grab strap and attaching hardware. Save the hardware for later use. 5. Install the grab strap. See either “For Kit 51936-08″ or “For All Other Kits” to install the grab strap. 2007 and Later FLSTF Models 1. Remove original equipment (OE) seat and mounting hardware following the instructions in the Owner’s Manual. 2. Remove and discard the OE grab strap and attaching hardware. 3. See Figure 3. Install two flange nuts (9) from the kit onto the OE grab strap mounting studs (as shown in Figure 1, Item 1). 4. Install the grab strap. See either “For Kit 51936-08″ or “For All Other Kits” to install the grab strap.

HARLEY DAVIDSON FXSTD DETACHABLE WINDSHIELD AND DOCKING HARDWARE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
INSTALLATION NOTE Use the Docking Hardware Kit to assemble two upper and two lower clamps. See the Service Parts illustration. The upper clamps use a mounting pin (4) and the lower clamps use a button head screw (5) to fasten the windshield mounting bushing. 1. Assemble the windshield docking hardware as follows: a. Install a larger chrome washer (6) and bushing (7) onto a button head screw (5). Thread the screw into the boss on one of the clamps (1), and tighten finger tight. Repeat for a second lower clamp. b. Install a larger chrome washer (6) and bushing (7) onto a mounting pin (4). Thread the pin into the boss on one of the clamps (1), and tighten finger tight. Repeat for a second lower clamp. 2 1 3 4 4 5 is 02187 1. Upper clamp 2. Lower clamp 3. Fork tubes 4.1/8 inch (3 mm) approximately 5.3.0 inch (76 mm) Figure 1. Installing Clamps NOTE Place shop rags on the headlamp, front fender and front of the fuel tank to prevent scratches to these components. Be sure the windshield assembly does not contact chrome or painted parts. Contact will cause scratches to chrome or painted parts. 2. See Figure 1. Install a lower clamp onto a fork tube using a smaller chrome washer and lock nut from the kit. Adjust so the clamp is approximately 1/8 inch (3 mm) from the top of the lower triple clamp, then finger tighten the lock nut. Repeat with the second lower clamp and fork tube. NOTE Keep front wheel straight to prevent brackets from scratching fuel tanks. See Figure 1. Install the clamps on the fork tubes so the bushing center lines are 3 inches (76 mm) apart. 3. Install an upper clamp onto a fork tube using a smaller chrome washer and lock nut from the kit. Adjust so the clamp is approximately 1/8 inch (3 mm) from the bottom of the upper triple clamp. Ensure that the center lines of the upper and lower bushings are 3 inches (76 mm) apart, then finger tighten the lock nut. Repeat with the second upper clamp and fork tube

HARLEY DAVIDSON FRONT AND REAR FENDER TIP TRIM INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
Installation GENERAL The original equipment (stock) fender tip lamp assemblies must be removed and the wire(s) must be unplugged or removed as specified in the following instructions. FRONT FENDER TIP REMOVAL OF STOCK FRONT FENDER TIP LAMP ON 1994 AND LATER FLT MODELS 1. Refer to the applicable FLT Service Manual. Remove headlamp assembly with housing. 2. Locate the 3-place connector [32 in wiring diagram] through which 12vdc and electrical ground are connected to the fender tip lamp assembly. The connector locations are as follows: FLTC Ultra: Under fuse and circuit breaker block FLHT/C/C-U: On bottom of left outer fairing bracket FLHR: On left front above air suspension valve NOTE Before disassembling the connector in the next step, refer to the applicable wiring diagram and check wire colors and connections to assure that connector [32] has been located. 3. Refer to the “DEUTSCH ELECTRICAL CONNECTOR” section in the FLT Service Manual and remove the leads, connected to the fender tip lamp, from the socket half, connector [32B]. 4. Insert a small screwdriver blade in rectangular slot at top center of fender tip lamp lens and gently pry lens from lamp. 5. Remove two screws and nuts that fasten fender tip lamp assembly to front fender. Gently remove the lamp assembly taking care not to damage wires connected to lamp assembly. 6. Reach under left side of fender and gently pull wires through rear hole in left side of fender and then through clips on left side of fender and finally through front hole and out of trim strip. REMOVAL OF STOCK FRONT FENDER TIP LAMP ON 1993 AND EARLIER FLT MODELS, FLSTC AND FLSTN 1. Insert a small screwdriver blade in rectangular slot at top center of fender tip lamp lens and gently pry lens from lamp. 2. Remove two screws and nuts that fasten fender tip lamp assembly to front fender. Gently remove the lamp assembly taking care not to damage wire connected to lamp assembly. 3. Unplug wire connector located about 3 in. from lamp assembly. Cover the socket half of connector (connected to motorcycle wiring) with electrical tape. INSTALLING FRONT FENDER TIP TRIM FROM KIT-ALL MODELS 1. Position fender tip trim over holes in fender and guide outer ends of fender tip trim into trim strips on sides of fender. 2. Insert studs on fender tip trim through holes in fender and secure with locknuts included in kit. Tighten locknuts to 6 in-lbs . REAR FENDER TIP REMOVAL OF STOCK REAR FENDER TIP LAMP ON ALL MODELS Follow steps 1 through 3 given above for “1993 AND EARLIER FLT MODELS, FLSTC & FLSTN” INSTALLING REAR FENDER TIP TRIM FROM KIT-ALL MODELS 1. Position fender tip trim over holes in rear fender. 2. Insert studs on fender tip trim through holes in fender and secure with locknuts included in kit. Tighten locknuts to 6 in-lbs

Incoming search terms:

HARLEY DAVIDSON CHROME 1.00 INCH (25.4 MM) DIAMETER HANDLEBAR KITS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and follow the instructions given to remove the main fuse. 2. Remove the outer fairing. See the service manual. 3. Remove the fairing cap. See the service manual. 4. FLHX Models: Handlebar-mounted mirrors (purchased separately) are required for proper installation of this handlebar. Removal of the inner fairing may be required, refer to the service manual. If fairing-mounted mirrors are being removed: Install the two small black plugs and large black plugs (purchased separately) to plug the fairing mirror holes. Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will dama ge painted and bod y panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) NOTE Immediately wipe up any brake fluid spillage with a clean, dry, soft cloth. Follow up by thoroughly wiping affected area with a clean, damp, soft cloth (small spills) or washing with a large quantity of soapy water (large spills). Cover nearby motorcycle surfaces with a polyethylene protective sheet to help protect against damage to finish caused by spillage or splashes of DOT 4 brake fluid. 5. Drain the brake fluid from the front brake reservoir and lines per the instructions in the service manual. NOTE Cover the front fender and the fuel tank with clean shop towels to prevent scratching. 6. Models with Radio: Remove the radio. See the service manual. Models without Radio: Remove the storage box. See the service manual. a. The four socket head screws fastening the radio or storage box to the left and right radio support brackets can be accessed through the oblong holes in the fairing brackets. Use a long shank ball-end socket to remove the screws. b. Pull the radio or storage box forward to remove it from the opening in the inner fairing. Remove brake line components carefully. Damage to seating surfaces can cause leakage. (00320a) 7. Remove and retain the button head screw on the underside of the fork stem and bracket assembly that holds the brake line manifold tee. 8. Note the front brake line routing and the orientation of the banjo fittings. Disconnect the brake line from the front brake calipers and the front brake master cylinder assembly. Save the banjo bolts, but discard the two gaskets found at each banjo fitting. See the service manual. 9. Remove the front brake line assembly. NOTES Refer to the parts catalog for this year and model for a replacement OE brake line assembly and clutch cable, if needed. Ask a Harley-Davidson dealer about the selection of Genuine Motor Accessory Custom Braided Clutch Cables and Brake Lines that are available. 10. Remove the front brake master cylinder and clutch lever assemblies from the handlebar. 11. Disconnect the clutch cable from the clutch lever. See the service manual.

Incoming search terms:

HARLEY DAVIDSON BASEPLATE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
51138-07 2007 VRSCAW, VRSCX, and VRSCDX 51220-07 2007 VRSCD 51120-07 Kit Contents See Figure 9 and Table 2. INSTALLATION 2 1 3 is02795 1. Seat tether 2. Hex nut 3. Seat post nut Figure 1. Remove Pillion 1. See Figure 1. Open rider’s seat and remove tether (1) from pillion base. 2. Remove and save seat post nut (3) and hex nut (2) from the pillion base for reinstallation. Lift pillion tabs off frame studs and push the pillion forward to release bottom of the pillion from pillion post on fender. Lift the pillion away from the motorcycle and temporarily set aside. 1 is02786 1. Electronics Caddy Figure 2. Remove Electronics Caddy 3. See Figure 2. Make note of electronics caddy location and wiring routes under pillion base. Press on the caddy’s retaining tabs and remove the caddy from the fender. Move the caddy and wiring to the side. 2 1 2 is02787 1. Pillion post 2. Screws and washers Figure 3. Remove Fender Support Screws and Washers 4. See Figure 3. Remove the four fender support screws and washers (2). Discard screws, but save three washers for re-installation. From under the fender use an allen wrench to hold the lower pillion screw while removing the upper pillion post (1). Save the pillion post and lower washer for reinstallation. 5. Thoroughly clean fender at pillion mounting area of all dirt and debris

HARLEY DAVIDSON FLSTN SADDLEBAG GUARD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
REMOVAL All Models 1. If equipped with saddlebags, removal may ease installation. Follow the instructions in the appropriate Service Manual or Instruction Sheet. 2. See Figure 1. Remove and discard the forwardmost fender support bolt (1). Repeat for the other side. 3. See Figure 2. On the left side, remove the footrest support mounting bolt (1) and footrest support bracket assembly (2). Discard the mounting bolt. 2005 – 2006 Models 1. Loosen the exhaust shields as necessary following the instructions in the appropriate Service Manual. Move as necessary for access. 2. Loosen the exhaust header nuts following the instructions in the appropriate Service Manual. 3. See Figure 3. Remove bolt (1) connecting the exhaust system (2) to the support bracket (3). 4. See Figure 4. Remove the two rear muffler bracket bolts (1). 5. See Figure 5. Move mufflers enough to access the rear bolt attaching the exhaust mounting bracket to the frame. Remove bolt (1) and discard. 2007 – Later Models NOTE On 2007 – later models, the frame tab (4) has a plug instead of a bolt (see Figure 6, item 1). 1. Remove plug and discard. 1 is05313 1. Fender support bolt (discard) Figure 1. Remove Docking Hardware 1 2 is05320 1. Footrest support mounting bolt 2. Footrest support bracket assembly Figure 2. Footrest Support Bracket Assembl NSTALLATION Right Side See Figure 5 or Figure 6. 1. See Figure 7. Install upper screw (7) in the fender support. Tighten screw finger-tight. 2. Install the lower screw (4 or 5) with the saddlebag guard, washer (9) and locknut (6) inside the frame. Tighten screw finger-tight. 3. Tighten the upper screw to 30 ft-lbs (41 Nm) . 4. Tighten the lower screw to 40 ft-lbs (54 Nm) . Tighten nut to 30 ft-lbs (41 Nm) . 5. 2005 – 2006 Models: a. Loosely install the exhaust header bolts. b. See Figure 4. Loosely install two rear muffler bracket bolts (1). c. See Figure 3. Loosely install bolt securing exhaust system (2) to support bracket (3). d. Tighten exhaust header bolts following the instructions in the appropriate Service Manual. e. Tighten support bracket bolt and rear muffler bracket bolts following the instructions in the appropriate Service Manual. f. Tighten exhaust shields following the instructions in the appropriate Service Manual. 6. Install saddlebag (if removed) following the instructions in the appropriate Service Manual or Instruction Sheet. 1 2 3 4 is05333 1. Lower saddlebag guard screw 2. Upper saddlebag guard screw 3. Saddlebag guard 4. Exhaust support bracket Figure 5. Install Saddlebag Guard – Right Side Shown (2005 Models) -J04645 2 of 4
2 1 3 4 is05332 1. Lower saddlebag guard screw 2. Upper saddlebag guard screw 3. Saddlebag guard 4. Frame tab Figure 6. Install Saddlebag Guard – Right Side Shown (2007-Later Models) Left Side 1. Loosely install upper screw (7) through the saddlebag guard and the fender support. NOTE Spacer (8) must be installed with the chamfer facing out. 2. See Figure 7. For 2005-2006 Models: Install lower screw (3) through the saddlebag guard, saddlebag guard spacer (8), footpeg support and the frame. Tighten to 30 ft-lbs (41 Nm) . For 2007 and later Models: Install lower screw (10) through the saddlebag guard, footpeg support and the frame. Tighten to 30 ft-lbs (41 Nm) . 3. Tighten upper screw to 30 ft-lbs (41 Nm)

Incoming search terms:

HARLEY DAVIDSON VRSC ACCESSORY SEATS AND PILLIONS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
INSTALLATION Installing Seat and Pillion Kits: 51584-01, 52028-02, 52036-01, 53432-02, or 52927-05 NOTE Proper installation of 53432-02 (Sundowner) and 52927-05 (Tallboy) requires installation of Fender Base Plate Kit 51120- 01 1. Refer to the appropriate Service Manual and remove the stock seat and pillion. 2. See Figure 2. Remove the two mounting bolts (2) from the passenger grabstrap (1). Save the bolts for re-installa- tion. NOTE The grabstrap must loop toward the rear. Check that the “Harley-Davidson” text on the grabstrap can be read from the front of the vehicle. 3. See Figure 2. Install stock grabstrap bolt, and one end of grabstrap as shown. While holding the grabstrap end parallel to the formed line of the fender, tighten the bolt to 8-12 Nm (71-106 in-lb ) . Repeat for opposite end of grabstrap. NOTES The new pillions included in Kits 52028-02 (Custom), 52036- 02 (Badlander) and 51584-01 (Leather Badlander) are installed from front-to-back. The pillion included in Kits 53432-02 (Sundowner) and 52927- 05 (Tallboy) must be installed through the grabstrap from back- to-front. To install the Sundowner or Tallboy Pillion on a motorcycle having a sissybar upright installed on Fender Base Plate Kit 51120-01, remove the upright before installing the pillion. Reinstall the upright after the Sundowner Pillion is installed. For kit numbers 52028-02 (Custom), 52036-01 (Vinyl Bad- lander) and 51584-01 (Leather Badlander) Seat Kits, be aware of the following: The 2003 Model Year 100th Anniversary VRSCA vehicle with two-tone sterling silver and vivid black paint has protective tape covering the rear under-the-seat area of the airbox cover. For the seats listed above, it will be necessary for cosmetic reasons, to carefully remove the protective tape and reapply it so it is in the correct position for these shorter-nose seats. Some trimming of the lower portion of the protective tape may be necessary to eliminate interference with the airbox cover latch. If necessary, reorder protective tape (48403-03). 4. Install new pillion into position through grabstrap. Prevent pinching TSSM control wiring by routing the cable through the channel on the underside of the pillion (see Figure 2) and away from the pillion mounting bolt. Pinched wiring may damage the TSSM system. 1 3 2 is00014 1. Pillion 2. Grabstrap 3. Pillion base mounting hole Figure 3. Pillion Base Mounting Hole 5. See Figure 3. Push the pillion (1) forward through the grabstrap (2) until the pillion mounting hole is approximately 25 mm (1 in.) forward of the hole (3) in the frame. 6. See Figure 2. Push down on the pillion and slide the pillion toward the rear to engage the pillion slot with the fender tongue (5). Push rearward until the pillion mounting holes align. After installing pillion, pull upward to be sure it is locked in position. While riding, a loose pillion can shift causing loss of control, which could result in death or serious injury. (00387a) 7. Install original pillion mounting bolt. Tighten bolt to 11-14 Nm (97-124 in-lb ) . 8. Re-install the sissybar upright, if removed earlier. 9. Position the seat (as if opened) onto the frame. Slide the seat forward to insert the seat-hinge pins into the bushings on the frame. 10. See Figure 1. Clip the plastic seat-hinge sleeve (2) over the seat hinge. 11. See Figure 1. Insert the seat tether (3) into the hole in the motorcycle frame. 12. Refer to the applicable Owner’s Manual and close the seat. Installing Seat Kits: 51595-05, 52024-01, or 51647-06 Kit 51595-05 requires the use of pillion kit 51594-05. Kit 51647-06 requires the use of pillion kit 51648-06. Kit 52024-01 requires the use of either the stock pillion or Touring Pillion 52023-01A. 1. Refer to the appropriate Service Manual and remove the stock seat.

Incoming search terms:

HARLEY DAVIDSON DYNA PASSENGER PILLION SEAT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
REMOVE SEAT NOTE When performing the following installation procedures, avoid scratching painted surfaces (fender, tank, etc.) with tools or metal seat tabs. 1. Remove screw to detach rear seat mounting bracket from fender. 2. Remove two capscrews that attach seat mounting bracket to bottom of stock seat. 3. Remove the existing seat from the motorcycle. Save the seat bracket and mounting screws for installation of the new seat. 4. If motorcycle has a grabstrap installed, remove nut and washer that holds passenger strap in place and remove strap. 5. See Figure 1. Remove the plastic cap from rearmost fender hole (3). 6. Remove the seat retention nut and washer from the solo seat mounting hole. 7. See Figure 2. A cable strap may be used as an installation aid to remove and reinstall the retention nut and washer. Place the retention nut (1) over the cable strap (3) so the wide end of the nut rests on the eye of the cable strap. Thread the cable strap up under the fender and through the rearmost fender hole. Pull up on the cable strap to hold the nut snug against the underside of the fender. 8. With the rib on the retention nut seated into the notch in the fender hole, slide the retention washer (2) into place from the rear. This will lock the retention nut in place. Remove the cable strap. 2 5 1 2 1 3 6 7 4 is00363 1. Retention nut and washer (2-up seat positon) 2. Retention nut and washer (solo seat position) 3. Rear-most fender hole 4. Middle fender hole 5. Grabstrap mounting hole 6. Flange screw 7. Plastic retention nut