Honda TRX 400EX INSTALLATION And REMOVAL INSTRUCTIONS

0

Filed Under (Honda) by admin on 14-12-2011

download
Quiet cores are supplied with this kit but not installed. To install the quiet cores remove both rear end caps ((turn downs) and install the quiet cores with the tubes facing inward. Re-install the end caps. REMOVAL Remove seat, disconnect attery and remove. Remove front fenders and side skirts. Remove fuel tank (make sure to shut fuel off and drain remaining fuel in the line before removing). Remove stock muffler first, then remove stock headers. Retain the 4 stock header bolts to install on your new exhaust system. Remove the rear bolt from your stock air box. Loosen stock intake clamp at carburetor. Remove stock boost bottle from the side of the boot. Loosen stock snorkel clamp at the air box, remove stock retaining clip at the front of the snorkel. Remove stock air box, intake boot and snorkel together from the ATV. Slide tarter solenoid off of stock mounting prongs. Remove Phillips screws from fuse holder and remove from plastic housing. Remove plastic battery housing from the ATV. Unplug tail light from harness. Unclip harness from the 2 clips above the battery. CARBURATION Now would be a good time to replace your stock main jet, with the supplied 190 main jet and replace your stock pilot jet with the supplied 48 pilot jet. Make certain that all hoses are tight and routed as stock. Be certain carb clamp is tight when re-installed. INTAKE BOOT Remove the intake boot from the stock air box. Take an exacto knife or razor blade and trim off the rubber piece that the hard plastic snorkel slips into. Trim around the intake boot staying the same distance as the rest of the lip. Take a hax saw and cut the groove as the rest of the boot is, being
careful not to cut all the way through (Picture Fig.2).

Incoming search terms:

1100cc Honda Goldwing Installation Manual

0

Filed Under (Honda) by admin on 29-04-2011

download
Receiver Hitch Installation Install all bolts loosely until all brackets are in place 1) Place motorcycle on center stand and be certain it is level. 2) Remove saddlebags if necessary for easier installation. 3) Mount bracket A to the lower front crash bar bolt Left side (new bolts provided) and top of left hitch arm. 4) Mount bracket B to the lower front crash bar bolt Right side (new bolts provided) and top of right hitch arm. 5) Bracket C mounts to rear of hitch and sub frame bolt located behind tail light (new bolt provided) This bracket mounts inside the rear fender. 6) Attach brackets D and E to rear of hitch. 7) Bracket F attaches to bottom of bracket D and trunk sub frame with U-bolts. Insert bottom U-bolts at step 9 8) Bracket G attaches to bottom of bracket E and trunk sub frame with U-bolts. Insert bottom U-bolts at step 9 9) Brackets D and E (with brackets F and G) attach to bottom rear saddlebag sub frame with U-bolts. 10) Tighten all bolts. INSTALLATION OF THE TOW-PAC HITCH CART. 1. Place your motorcycle on a smooth flat surface, like a garage floor, and rest it on its center stand. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle. Now push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bolt. 5. Push the motorcycle off of the center stand and risers if used. 6. Bolt leanstop braces to hitch. (Bolt inserts from the bottom) Be certain to replace washers/spacers in the same configuration as when you removed them. see diagram next page 7. Check all bolts for tightness. 8. You are now ready for the test ride. A. Keep your feet up! B. Ride slowly in first gear until you are comfortable with the Tow-Pac system.

Incoming search terms:

Honda Shadow A.C.E. v. Yamaha V-Star 1100 Middleweight Import Cruiser Shootout

0

Filed Under (Tips and Review) by admin on 25-11-2010

download
You want a big cruiser but you don’t need a large 1500 cc behemoth that weighs close to half-a-ton fully loaded. You want something you can cruise down the boulevard on but you want to be able to handle a corner or two. You want classic styling but you insist on reliability as well. If these are your guidelines, then Honda and Yamaha might have what you’re looking for in the guise of the Honda Shadow American Classic Edition and Yamaha V-Star 1100. Shadow ACE 1100 The ACE and V-Star have a few things in common: Both sport requisite V-twin powerplants (75° for the V-Star and 45° for the ACE) and both possess typical Japanese refinement. Aside from these similarities, the two rides are very different machines. While both machines are shaft driven, the ACE uses the shaft housing as the swingarm. Although this arrangement is effective, it’s a bit lacking style-wise. However, the whitewall tires and the classic fenders and tank help to create a traditional design that turns heads when you’re out and about. The V-Star uses a different approach, utilizing a pivoting sub-frame design with a hidden mono-shock that keeps the lines fluid and consistent with the rest of the bike. Although this beast isn’t equipped with whitewall tires, it still cuts a graceful, glittering profile. The only flaw we noticed was the small headlight that

Incoming search terms:

Honda Shadow750 ACE Installation Manual

0

Filed Under (Honda) by admin on 21-11-2010

download
1) Place motorcycle on a smooth level surface on its side stand. 2) Install leveling screw jacks so that motorcycle is in an upright and level position. 3) Remove saddlebags. 4) Mount bracket A ( left side ) to the 3 bolts that attach the rear fender and sub frame to the main motorcycle frame. new bolts provided 5) Mount bracket B ( right side ) to the 3 bolts that attach the rear fender and sub frame to the main motorcycle frame. new bolts provided 6) Bracket C mounts to the outside of bracket A at the rear lower hole. ( left ) 7) Bracket D mounts to the outside of bracket B at the rear lower hole. ( right ) 8) Bracket E ( left ) attaches to the outside of the motorcycle frame just under the rear foot peg and above the frame weld with the provided U-bolt. see diagram 9) Bracket F ( right ) attaches to the outside of the motorcycle frame just under the rear foot peg and above the frame weld with the provided U-bolt. see diagram 10) Bolt brackets C and D to the top rear of the receiver hitch. 11) Bolt brackets E and F to the top of the forward arms of the receiver hitch. 12) Tighten all bolts at this time. 13) Remount saddlebags and check all bolts for tightness. 1. Place your motorcycle on a smooth level surface and attach leveling jack stands. 2. Assemble axles, wheels, and fenders onto the tow-pac hitch cart. 3. Push the hitch mount into the receiver hitch. (this might bea little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bolt. 5. Align InstaTrike wheels. (initial installation only. Check periodically and realign if necessary) 6. Bolt lean stop braces to hitch. (Bolt inserts from the bottom) Be certain to replace washers/spacers in the same configuration as when you removed them.

Incoming search terms: