Wildfire WFH 150-T Touring Scooter Specification And Owner's Manual

0

Filed Under (Wildfire) by admin on 29-11-2010

download
Engine Oil Replacement • Replace the engine oil after the first 50 miles or 1 hour with 5w50, 10w50 or 15W50 synthetic engine oil. Then replace again every 1,500 miles or 1 each year. Check oil level every 500 miles, add oil if needed. Changing the Engine Oil (1).Warm up the engine for a few minutes. (2).Stop the engine. (3). Place scooter on center stand. (4).Place an oil pan under the engine and remove the dipstick. (5).Remove the drain plug and drain the oil. Reach in drain hole, pull out filter clean and reinstall, after all oil drains out. (6).Reinstall drain plug. (7). Fill the engine with oil until the level is in the designated area on the dipstick. (8).Start the engine and check for oil leaks. If a leak is found stop the engine immediately and look for cause. Rear Wheel Oil Replacement • Replace the gear oil after the first 500 miles with 5W/50 synthetic engine oil. Replace the gear oil again every 4 months or every 2000 miles. • Replacing the Gear Oil (1).Put the scooter on the center stand (please see photo below) . (2).Place an oil pan under the gear case (please see photo below) . (3).Remove the oil filler bolt and the drain plug to drain the oil (please see photo below) . (4).Reinstall and tighten the drain plug. (5).Fill the gear case with oil (please see photo below) . (6).Reinstall the oil filler bolt. (7).Check for oil leakage. Cleaning Air Cleaner Be sure to check the air cleaner regularly. (1).Place the scooter on the center stand. (2).Unscrew and remove the left side panel. (3).Remove the air cleaner cover by removing the screws. (4).Take out the air cleaner by removing the screws. (5).Remove the air cleaner element and wash it gently, but thoroughly in solvent. Replace if damaged. (6).Squeeze out the excess solvent and dry it. (7).Apply oil to the entire surface of the air cleaner and squeeze out the excess oil. It should be damp but not dripping. (8).Install the air cleaner, cleaner cover, and left side panel. center stand 1 oil pan 2 3 oil drain plug oil pan 5 Main Switches On Position: • Electrical circuits are switched on. The engine can be started and the key can not be removed.

Incoming search terms:

Honda VTX1800F, VTX1300C, VTX1800C Plated Saddle Bag Installation Manual

0

Filed Under (Honda) by admin on 14-11-2010

download
Instruction Manual > Your saddlebag supports will install in just a few minutes using common tools. Read all instructions carefully and completely before installing your new saddlebag supports. 1. Remove your stock fender rail bolts. 2. Place the supplied spacers in the recessed holes on the fender rails (large spacer to the front, small spacer to the rear). 3. Install your Cobra saddlebag supports using the supplied button head bolts (where the stock bolts were removed) the saddlebag supports should hang towards the rear and away from the motorcycle. 4. Torque bolts to factory specifications. Note: If using Cobra sissy bar mount the saddlebag supports over the sissy bar brackets and do not use supplied spacers. Cobra recommends you always wear a helmet while riding. Please never operate your motorcycle while under the influence of alcohol and/or drugs. Enjoy the new look of your motorcycle and please ride safely

SUZUKI VOLUSIA 800, C50, M50 Left/ Right Saddlebag Installation Manual

0

Filed Under (Suzuki) by admin on 14-11-2010

download
Your saddlebag supports will install in just a few minutes using common tools. Read all instructions carefully and completely before installing your new saddlebag supports. 1. Remove your stock fender rail bolts. 2. Install your Cobra saddlebag supports using the supplied 8mm x 65mm button head bolts (where the stock bolts were removed), the saddlebags should hang towards the rear and away from the motorcycle. 3. Torque bolts to factory specifications Cobra recommends you always wear a helmet while riding. Please never operate your motorcycle while under the influence of alcohol and/or drugs. Enjoy the new look of your motorcycle and please ride safely

Incoming search terms:

Aprilia ntic 500 Change

0

Filed Under (Aprilia) by admin on 07-11-2010

download
Time and Ease: Easy­ Under 30 Minutes Tools/Supplies: Ratchet w/sockets or wrenches, oil, oil pan, oil filter, rags, funnel Step 1: Put scooter on center stand and allow the engine to cool. Step 2: Unscrew and extract the cap­dipstick (1) . Step 3: Unscrew and remove the engine oil filter (3) . Step 4: Unscrew and remove the oil drain plug (4) . Allow the oil to drain completely. Step 5: Install a new oil filter (3) , being careful to lubricate the O­ring on the filter with oil. Step 6: Tighten the engine oil drain plug (4) . Step 7: Fill through the filling hole (2) with approximately 1.7 L of 5W­40 Synthetic or other that exceeds API ST Specifications. Step 8: Tighten the oil level dipstick (1) . Step 9: Start the engine and let run for a few minutes, Shut it off and let it cool. Check the engine oil level again using the dipstick (1) , and top it off if necessary, without ever exceeding the “MAX” level.

Incoming search terms: