2005 SUZUKI SV1000 SPECIFICATIONS AND SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
TIRE PRESSURE FUEL + OIL COLD INFLATION TIRE PRESSURE FRONT REAR SOLO RIDING ITEM Fuel type kPa 250 250 DUAL RIDING kPa 250 290 NOTE E-03, 28, 33 The others E-33 The others Fuel tank Engine oil type Engine oil capacity SPECIFICATfON Use only unleaded gasoline of at least 87 pump octane (R12 + M12) or 91 octane or higher rated by the research method. Gasoline containing MTBE (Methyl Tertiary Butyl Ether), less than 10% etha- nol, or less than 5% methanol with appropriate cosolvents and corrosion inhibitor is permissible. Gasoline used should be graded 91 octane or higher. An unleaded gasoline is recommended. 16 L (4.2/3.5 USnrnp gal) 17 L (4.513.7 USIlmp gal) * SAE 10W-40, API SFlSG or SHISJ with JASO MA kgf/cm2 2.50 2.50 Change Filter change Overhaul psi 36 36 kgflcrn2 2.50 2.90 2 700 rnl (2.912.4 USllmp qi) 2 900 ml (3.112-6 US/lmp qt) 3 300 ml (3.U2.9 USllrnp qt) psi 36 42 CRANKCASE-CRANKSHAFT BEARING SELECTION Select the specrffed bearings from the crankcase bore I. D. code. The crankcase bore I.D. code (A) “A, “6″ or “C”, is stamped on the inside of each crankcase half. Bearing selection table Bearing thickness I.D. code @9 A B C Bearing must be replaced as a set. I.P. specification 52.000 – 52.006 mrn (2.0472 – 2.0475 in) 52.006 – 52.01 2 mm (2.0475 – 2.0477 in) 52.01 2 – 52,018 mm (2.0477 – 2.0479 in) Color (Part No.) Green (1 2229-1 6GOO-OAO) Black (1 2229- tGG00-OBO) Brown (I 2229- 16GOO-OCO) Color code 9 Bearing Green Black Brown Thickness 1.999 – 2.002 mrn (0.0787 – 0.0788 in) 2.002 – 2.005 mm (0.6788 – 0.0789 in) 2.005 – 2.008 rnm (0.0789 – 0.0791 in) FI SYSTEM WIRING DIAGRAM I ECM TERMINAL (For KCModel) ‘& ECM TERMINAL (For K5-Model) FAIL-SAFE FUNCTION & FI system is provided with fail-safe function ta allow the engine to start and the motorcycle to run in a mini- mum performance necessary even under malfunction condition

SUZUKI SV650 Fl SYSTEM DIAGNOSIS SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
PRECAUTIONS IN SERVICING When handling the component parts or servicing the FI system, observe the following points for the safety of the system . ELECTRICAL PARTS CONNECTOR/COUPLER • * When connecting a connector, be sure to push it in until a click is felt. •With a lock type coupler, be sure to release the lock when isconnecting, and push it in fully till the works when connecting it. • * When disconnecting the coupler, be sure to hold the coupler body and do not pull the lead wires . • * Inspect each terminal on the connector/coupler for looseness or bending. • * Inspect each terminal for corrosion and contamination. The terminals must be clean and free of any foreign material which could impede proper terminal contact . •Inspect each lead wire circuit for poor connection by shaking it by hand lightly. If any abnormal condition is found, repair or replace. •When taking measurements at electrical connectors using a tester probe, be sure to insert the probe from the wire harness side (backside) of the connector/coupler . 0 4 40 O/ 40 16~ Id •When connecting meter probe from the terminal side of the coupler (connection from harness side not being possible), use extra care not to force and cause the male terminal to bend or the female terminal to open . Connect the probe as shown to avoid opening of female ter- minal. Never push in the probe where male terminal is supposed to fit. •Check the male connector for bend and female connector for excessive opening. Also check the coupler for locking (looseness), corrosion, dust, etc . FUSE • * When a fuse blows, always investigate the cause correct it and then replace the fuse . • * Do not use a fuse of a different capacity . • * Do not use wire or any other substitute for the fuse . ECMNARIOUS SENSORS •Since each component is a high-precision part, great care should be taken not to apply any sharp impacts during removal and installation. • * Be careful not to touch the electrical terminals of the ECM . The static electricity from your body may damage this part . FI SYSTEM DIAGNOSIS 4-3
4-4 FI SYSTEM DIAGNOSIS • When disconnecting and connecting the ECM, make sure to turn OFF the ignition switch, or electronic parts may get dam- aged. • * Battery connection in reverse polarity is strictly prohibited . Such a wrong connection will damage the components of the FI system instantly when reverse power is applied . • * Removing any battery terminal of a running engine is strictly prohibited. The moment such removal is made, damaging counter electromotive force will be applied to the ECM which may result in serious damage.

SUZUKI SV 1000 RADIATOR (COOLING SYSTEM) SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
FI SYSTEM MALFUNCTION CODE AND DEFECTIVE CONDITION MALFUNCTION CODE DETECTED ITEM DETECTED FAILURE CONDITION CHECK FOR COO NO FAULT C11 Camshaft position sen- sor The signal does not reach ECM for more than 3 sec . after receiving the starter signal . The camshaft position sensor wiring and mechanical parts (Camshaft position sensor, intake cam pin, wiring/coupler con- nection) C12 Crankshaft position sensor The signal does not reach ECM for more than 2 sec . after receiving the starter signal . The crankshaft position sensor wiring and mechanical parts (Crankshaft position sensor, wiring/coupler connection) C13 Intake air pressure sensor The sensor should produce following voltage . (0.50 V < sensor voltage < 4 .85 V) Without the above range, C13 is indicated. Intake air pressure sensor, wiring/coupler connection C14 Throttle position sen- sor The sensor should produce following voltage . (0.20 V < sensor voltage < 4 .80 V) Without the above range, C14 is indicated. Throttle position sensor, wiring/coupler connection C15 Engine coolant temperature sensor The sensor voltage should be the following. (0.15 V <_ sensor voltage < 4 .5 V) Without the above range, C15 is indicated. Engine coolant temperature sensor, wiring/coupler connection C21 Intake air temperature sensor The sensor voltage should be the following. (0.15 V < sensor voltage < 4 .5 V) Without the above range, C21 is indicated. Intake air temperature sensor, wiring/coupler connection C22 Atmospheric pressure sensor The sensor voltage should be the following. (0.50 V < sensor voltage < 4 .5 V) Without the above range, C22 is indicated. Atm. pressure sensor, wiring/coupler connection C23 Tip over sensor The sensor voltage should be the following for more than 2 sec . after ignition switch turns ON . (0 .20 V < sensor voltage < 4 .80 V) Without the above value, C23 is indicated. Tip over sensor, wiring/coupler connection C24 or C25 Ignition signalCrankshaft position sensor signal is produced and ECM determines the ignition signal but signal from ignition coil is interrupted continuous by 4 times or more. In this case, the code C24 or C25 is indicated. Ignition coil, wiring/coupler connection, power supply from the battery SERVICING INFORMATION 8 .3 C28 Secondary throttle valve actuator No operating voltage is supplied from the ECM, C28 is indicated. STVA can not operate. STVA lead wire/coupler, STVA C29 Secondary throttle valve position sensor The sensor should produce following voltage . (0.10 V < sensor voltage < 4 .90 V) Without the above range, C29 is indicated . Secondary throttle position sensor, wiring/coupler connection C31 Gear position signalGear position signal voltage should be higher than the following for more than 2 seconds. (Gear position switch voltage >_ 0 .6 V) Without the above value, C31 is indicated. Gear position sensor, wiring/coupler connection, gearshift cam, etc. C32 or C33 Fuel injector Crankshaft position sensor signal is produced and ECM determines the injection signal but fuel injection signal is interrupted continuous by 4 times or more. In this case, the code C32 or C33 is indicated. Injector, wiring/coupler connection, power supply to the injector C41 Fuel pump relay No voltage is applied to fuel pump although fuel pump relay is turned ON, or voltage is applied to fuel pump although fuel pump relay is turned OFF . Fuel pump relay, connecting lead, power source to fuel pump relay C42 Ignition switchIgnition switch signal is not input in the ECM . Ignition switch, lead wire/coupler C44 Heated oxygen sensor (HO2S) [For E-02, 19] During 02 feedback control, 02 sensor voltage is higher or lower than the specification . No signal is detected during engine operation or no electrical power is supplied from the battery . HO2S lead wire/coupler connection Battery voltage supply to the HO2S C49 PAIR control solenoid valve (PAIR valve) When no operating voltage is supplied from the ECM, C49 is indicated. PAIR valve can not operate. PAIR valve lead wire/coupler

Incoming search terms: