Kawasaki Mule 3010 Hood Rack Installation And Operations Manual

0

Filed Under (Kawasaki) by admin on 28-04-2012

download
1. Install the Seizmik Brush Guard. – Have a friend hold the brush guard (G) in place while you slide the 1.0″ dia. tube clamps (K) in place over the middle tube of the OEM bumper, as shown in Figure 1. Secure each one in place with one of the 3/8″ x 2.25″ bolts (N), two 3/8″ washers (Q), and one 3/8″ nylock nut (R). Repeat at the top tube of the OEM bumper using the 1.5″ dia. tube clamps (J), and 3/8″ x 1.75″ bolts (O). VEHICLE FRONT Figure 2. 2. Mounting brackets – Attach the two hood rack mounting brackets to the mounting pads of the brush guard, as shown in Figure 2. Use four of the 3/8″ x 1.0″ bolts (P), eight 3/8″ washers (Q), and four 3/8″ nylock nuts (R) per mounting pad. Snug down the fasteners but do not fully tighten them yet. 3 Figure 3. 3. Crush sleeves – Insert a crush sleeve (B) into each cantilever arm assembly (C & D), as shown in Figure 3. 4. Cantilever arms – Position the Driver side cantilever arm (C) on the mounting bracket, and insert a 3/8″ dia. pivot bolt (M), as shown in Figure 4. Add a 3/8″ washer (Q) and nylock nut (R) on the other side and snug down the assembly; leave the fasteners loose enough so the components can be repositioned for fitment. Repeat this step for the passenger side. Figure 4. 4 Figure 5. 5. Lock pins – Insert the 1/2″ lock pins (Y) into the tabs on each side of the Brush Guard, fixing the cantilever arms in place, as shown in Figure 5.

Incoming search terms:

Harley-Davidson Amp Module – Base Kit Installation Manual

0

Filed Under (Harley Davidson) by admin on 10-03-2012

download
Technique for removal of Ampseal contacts from the connector housing (refer to Photos 5 and 6): Grab the wire to be removed (shown in the next section) with needle nose pliers or hemostats. While rotating the wire back and forth over a half turn (1/4 turn in each direction), gently pull the wire until the contact is removed. Photo 5- Pin Removal, Step 1 Photo 6- Pin Removal, Step 2 End of Removal Technique Installing Kennedy Harnesses part #85910 and 85911 Locate Kennedy harnesses part #85910 and 85911 and 5 pieces of 1/8″ diameter x 2″ shrink-wrap, from kit part number 85615-10. Refer to Figure 1 (Pre-’06) and Figure 1a (2006 and Newer) on the next page, and make the connections between Ampseal connector 28B and Kennedy harness 85910, and harness 28B and Kennedy Harness 85911.

HARLEY DAVIDSON FXSTD DETACHABLE WINDSHIELD AND DOCKING HARDWARE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
INSTALLATION NOTE Use the Docking Hardware Kit to assemble two upper and two lower clamps. See the Service Parts illustration. The upper clamps use a mounting pin (4) and the lower clamps use a button head screw (5) to fasten the windshield mounting bushing. 1. Assemble the windshield docking hardware as follows: a. Install a larger chrome washer (6) and bushing (7) onto a button head screw (5). Thread the screw into the boss on one of the clamps (1), and tighten finger tight. Repeat for a second lower clamp. b. Install a larger chrome washer (6) and bushing (7) onto a mounting pin (4). Thread the pin into the boss on one of the clamps (1), and tighten finger tight. Repeat for a second lower clamp. 2 1 3 4 4 5 is 02187 1. Upper clamp 2. Lower clamp 3. Fork tubes 4.1/8 inch (3 mm) approximately 5.3.0 inch (76 mm) Figure 1. Installing Clamps NOTE Place shop rags on the headlamp, front fender and front of the fuel tank to prevent scratches to these components. Be sure the windshield assembly does not contact chrome or painted parts. Contact will cause scratches to chrome or painted parts. 2. See Figure 1. Install a lower clamp onto a fork tube using a smaller chrome washer and lock nut from the kit. Adjust so the clamp is approximately 1/8 inch (3 mm) from the top of the lower triple clamp, then finger tighten the lock nut. Repeat with the second lower clamp and fork tube. NOTE Keep front wheel straight to prevent brackets from scratching fuel tanks. See Figure 1. Install the clamps on the fork tubes so the bushing center lines are 3 inches (76 mm) apart. 3. Install an upper clamp onto a fork tube using a smaller chrome washer and lock nut from the kit. Adjust so the clamp is approximately 1/8 inch (3 mm) from the bottom of the upper triple clamp. Ensure that the center lines of the upper and lower bushings are 3 inches (76 mm) apart, then finger tighten the lock nut. Repeat with the second upper clamp and fork tube

Incoming search terms:

HARLEY DAVIDSON SOFTAIL DELUXE SEATS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
These kits fit 2005 and later FLSTN model motorcycles. Additional Parts Required NOTE A Service Manual for your model motorcycle is available from a Harley-Davidson Dealer. Kit Contents See Figure 3 and Table 1. INSTALLATION 1. Remove existing seat according to Owner’s Manual Instructions. Save all attaching hardware. 2. See Figure 1. Install two flange nuts (1) from kit onto the seat mounting studs. Tighten flange nuts to 5-8 ft-lbs (7- 11 Nm) . 1 is03023 1. Install flange nuts Figure 1. Flange Nut Locations NOTE See Figure 3 for Steps 3-6. 3. Remove two screws (A) and rear mounting bracket (B) from stock seat. Save all hardware. 4. Install the rear mounting bracket (B) removed in Step 3 onto the new seat using the seat bracket screws (A). Tighten screws to 19 in-lbs (2.1 Nm) . 5. Install new seat (1) on the motorcycle by inserting the tab at the front of the seat into the slot at the rear of the fuel tank. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 6. Fasten rear seat bracket (B) to fender nut using stock mounting screw (C). 7. See Figure 2. To install grabstrap, remove front screw and washer from rear fender support. Install grabstrap with thick washers (1), thin washers (3) and screws (4) from kit. Tighten to 21-27 ft-lbs (28-37 Nm)

HARLEY DAVIDSON VRSC SADDLEBAG SUPPORT KIT (WIDE TIRE) REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
REMOVAL Remove Pillion and Rear Fender NOTE If possible, lift the rear of the motorcycle up so the rear wheel drops to the bottom of shock travel. This will help provide clearance between the rear tire and fender when installing the mounting brackets. 1. Open the rider seat. 2. See Figure 1. Remove rider seat post (1), nut (2), and washer (3) from passenger pillion. Slide grabstrap (4) forward off pillion. Save mounting hardware for kit installation. 3. Push passenger pillion forward to release slot on bottom of pillion from post on fender tongue. 4. See Figure 2. Lift pillion up to remove lanyard (1) from hole in center of passenger pillion (2). Then lift pillion away from motorcycle. 5. Disconnect turn signal and tail light electrical connections from back of rear electrical caddy. Note position for later installation. 6. See Figure 3. Unsnap rear electrical caddy (1) from rear inner fender. 7. Remove and save two fender support bolts (2), washers (3), and grabstrap (4) from rear fender. 1 2 3 4 is03548 1. Rider seat post 2. Nut 3. Washer 4. Grabstrap Figure 1. Passenger Pillion and Mounting 2 1 3 i03571 1. Seat lanyard 2. Hole in pillion 3. Passenger pillion Figure 2. Seat Lanyard and Passenger Pillion 8. Remove four remaining fender support bolts (2) and washers (3) near center of rear fender. 9. Remove rear fender from vehicle. 3 2 4 2 3 2 3 1 is03544 1. Rear electrical caddy 2. Fender support bolt (6) 3. Washer (6) 4. Grabstrap Figure 3. Grabstrap, Rear Electrical Caddy, and Fender INSTALLATION Install Attach/Release Weldment, Rear Fender, and Grabstrap NOTE Apply Loctite 243 (blue) to last four threads of leave-on bracket screws. 1. See Figure 4. Install leave-on bracket (1) to outside surface of inner fender using two button head screws (2) and nuts (3). Tighten screws to 48 Nm (35 ft-lbs). Repeat for opposite side. 2. See Figure 5. Install release/attach weldment (1) to leave- on brackets (2) using two washers (3) and socket head cap screws (4). Tighten screws to 25 Nm (18 ft-lbs). Repeat for opposite side.

HARLEY DAVIDSON SPORT WIND DEFLECTOR AND WINDSHIELD KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 03-03-2011

download
HEADLAMP VISOR INSTALLATION (2004 ONLY) 1 2 is 01467 1. Headlamp 2. Headlamp bracket mounting screws Figure 1. Remove Headlamp Mounting Screws (Left Side Shown) 1. See Figure 1. While holding the headlamp (1), remove the left and right headlamp bracket mounting screws (2). 2. See Figure 5. Obtain the headlamp visor (2) from the kit. 3. See Figure 2. Orient the headlamp visor (1) between the headlamp and headlamp mounting bracket (2) and reinstall the headlamp bracket mounting screws (3) securing the visor and headlamp to the headlamp mounting bracket. 4. Refer to the Service Manual and adjust the headlamp for the correct angle. 2 1 3 is01468 1. Headlamp visor 2. Headlamp mounting bracket 3. Headlamp mounting bracket screw Figure 2. Install Visor Between Headlamp and Mounting Bracket (Left Side Shown) 1 2 3 is03212 1. “RT” or “LFT” marking 2. Hinge-pin head faces up 3. Clamp post socket faces outward Figure 3. Fork Tube Clamp and Post Identification (Right-Side Clamp Shown) WINDSHIELD INSTALLATION 1. See Figure 5. Obtain one of the lower mount kits from the windshield kit carton. Identify the fork tube clamp for right- side (RT) or left-side (LFT) installation as indicated in Figure 3. NOTE The lower grommets (4) have been pre-installed into the Lexan® windshield. 2. Insert the rounded end of the post into the socket in the fork-tube clamp, oriented as shown in Figure 5. Lining up the hole in the end of the post with the hole in the clamp. With a 3 mm hex key, fasten the post to the clamp with the flat-head screw (16) from the kit, and tighten to 6.8 Nm (60 in-lbs ). 3. Place the clamp around the correct-side fork tube with the hinge-pin head facing up. Insert the two longer screws (15) from the lower mount kit through the counterbored holes in the outboard side of the clamp, and thread the screws part-way into the tapped holes in the inboard half. 4. Position the clamp so the top surface is approximately 6 to 13 mm (1/4 to 1/2 inch) below the upper triple-tree, and the hinge pin is straight forward. With a 4 mm hex key, tighten the screws just enough to hold the clamp in posi- tion. 5. Obtain the remaining lower mount kit and repeat Steps 2 through 4 to install the clamp to the opposite fork tube. 6. Obtain the upper mount kit from the windshield kit carton. NOTE The upper grommets (4), socket assemblies (3), windshield mount caps (6) and 5 mm screws (9) have been pre-installed into the windshield. 7. Place one of the handlebar clamps (5) onto one side of the handlebar, in the straight section between the riser and the handlebar controls, oriented as shown in Figure 4. NOTE Temporarily disengage the switch harness retainer from the handlebar to allow installation of the clamp.

HARLEY DAVIDSON ENRICHENER KNOB COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-02-2011

download
Additional Parts Required Loctite® 222 (purple) Installation NOTE If there are any rough edges around enrichener knob that prevent enrichener knob cover from sliding in place, remove them using fine grit sandpaper or emery cloth. 1. See Figure 1. Install collet (4) to the enrichener knob (A), the enrichener knob cover (2) and gasket (3) as shown. Apply Loctite 222 (purple) to threads of screw (1). Line up hole in collet with hole in enrichener cover and insert screw. Tighten screw. 1 2 3 A 4 is03857 1. Screw 2. Enrichener Knob Cover 3. Gasket 4. Collet Figure 1. Enrichener Knob Cover Installation

HARLEY DAVIDSON SPORTSTER HAND GRIPS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
Remove and Install the Left Grip 1. See Figure 1. Using a T27 TORX®drive head, remove the two screws with flat washers securing the handlebar clamp (3) to the clutch lever bracket. Remove the clamp and position the clutch hand lever assembly away from the handlebar. 2. Using a T25 TORX®drive head, loosen but do not remove the upper and lower switch housing screws (1). 3. Remove the end cap from the existing left handlebar grip if so equipped. Remove the grip by carefully cutting it away from the handlebar using a sharp blade or knife. Do not lubricate left handlebar grip before installation. Lubricating grip can cause it to come off while riding, which could result in loss of control and death or serious injury. (00315a) NOTE Make sure that the handlebar surface and the inside of the grip are smooth, dry and thoroughly cleaned of all dirt or adhesive residue. 4. Position the new left grip (4) so the larger flange (5) is at the bottom. Push the grip fully onto the handlebar. 5. Fit the grooves (2) on the outboard side of the upper and lower switch housing over the flanges on the end of the grip, then loosely fasten the two screws. 6. Position the clutch hand lever assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the bottom of the clutch lever bracket. 7. Align the holes in the handlebar clamp with those in the clutch lever bracket, and loosely fasten the two screws with flat washers. Adjust the switch housing and clutch hand control position for rider comfort. 8. Using a T27 TORX®drive head, tighten first the upper, then the lower handlebar clamp screws to 60-80 in-lbs (6.8-9.0 Nm). 9. Using a T25 TORX®drive head, tighten first the lower, then the upper switch housing screws to 35-45 in-lbs (4.0-5.1 Nm). Remove and Install the Right Grip 1. Refer to the RIGHTHANDLEBARSWITCH section of the service manual for removal of the switch housing assembly. This is necessary to access the throttle cables. 2. Refer to the THROTTLECONTROL section of the service manual to disconnect the throttle cables and remove the existing right grip/throttle sleeve assembly. After removal, make sure that the handlebar end is clean and smooth. 3. Follow instructions in the service manual to install the new right grip/throttle sleeve to the handlebar and connect the throttle cables. 4. Verify that the right grip/throttle sleeve rotates and returns freely and does not bind on the handlebar or switch housing.

HARLEY DAVIDSON PIVOT BOLT COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 22-02-2011

download
This kit fits all 2004 and later XL (Sportster®) model motorcycles INSTALLATION Right-Side Pivot Bolt Cover Installation Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. See Figure 1. Start a set screw (2) from the kit into one of the pivot bolt covers (1) about two or three turns. 2. Note the position of the bottom-most flat on the rear-fork pivot hex-head bolt (3). Line up the pivot bolt cover over the bolt head so the set screw is centered on the hex flat. Use the 3/32 inch hex key from the kit to tighten the set screw securely to the head of the rear-fork pivot bolt. 3. Make sure the pivot bolt cover is clean and free of any oil or grease. Remove the protective backing from the adhesive disk on the back of the decorative insert (9). Install the decorative insert onto the end of the pivot bolt cover with the image or text upright and parallel to the ground. Press the insert firmly against the end of the pivot bolt cover and hold pressure for 30 seconds. After releasing pressure, avoid direct contact with the insert for about 20 minutes. Left-Side Pivot Bolt Cover Installation 4. Models without passenger footrests: Use an 8 mm hex key to remove the bolt (5) retaining the double-tube clamp (4). Models with passenger footrests: Use an 8 mm hex key to remove the two bolts (5) and the left-side passenger footrest and bracket assembly (6). 5. Start a set screw (2) from the kit into one of the pivot bolt covers (1) about two or three turns

Incoming search terms:

HARLEY DAVIDSON SUPPLEMENT ARY 12 VOLT POWER SOURCE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
Installation NOTE This power source can be mounted on either side cover of the motorcycle, except on models with cruise control, which must have the power source mounted on the right side cover. 1. Remove seat and the side cover chosen for installation (see note above). 1 WARNING To avoid accidental start-up of motorcycle, and possible personal injury, disconnect the battery cables (negative cable first) before performing any of the following procedures. If the positive cable should contact ground with the negative cable installed, the resulting sparks may cause a battery explosion resulting in personal injury. 2. Disconnect battery, negative cable first. 3. See Figure 1. A 7/8 inch diameter hole needs to be drilled in the top of the side cover to mount the power source. It is important that the hole is properly located as follows, before cutting : a. Cut out template on page 3. Line the template up on the outside top of the cover using the top and rear cover edges as guides as shown in the illustration. Tape the template in place. b. After the template is in place, locate the appropriate hole on the template that matches the applicable year and side cover. Check to be sure that the entire hole area is on the flat top surface of the cover. No part of the hole should extend onto the sharply curved edge of the cover. 4. Carefully drill a 7/8 inch diameter hole at the location marked on the template. Drill from the outside of the cover to the inside. 5. See Figure 2. Unscrew outer sleeve of socket assembly (1) from socket body. Place the socket body into the cover hole and secure the socket in place by screwing

Incoming search terms: