Harley-Davidson FLTR/ FLH/ FLHT/ FLHR EFI models 1995-2001 Variable Pressure Fuel Regulator Intallation manual

0

Filed Under (Harley Davidson) by admin on 27-04-2012

download
1 . Ensure vehicle runs correctly through all rpm ranges and idles correctly before attempting any work. It is highly recommended that a pressure / flow test be carried out before & after installation of the VariReg to determine fuel system condition . Stock HD 300 kPa / 44 psi, VariReg as delivered 360 kPa / 52 psi Note: In some countries gas stations do not “final filter” the fuel & therefore we recommend that the fuel filter canister be replaced every 15,000 klms (10,000 miles). Restriction of the fuel by way of a blocked or partially blocked filter will result in difficulty in tuning or failure to obtain satisfactory results during tuning. Should you experience difficulties in tuning, see Diagnosing fuel filter and pump faults 2. Remove air filter cover, air filter and backing plate. Check Throttle Position Sensor value at completely closed throttle as best performance will be obtained at the nominated settings. This will require backing off the idle screw and cold start idle actuator and screw adjustment as described in the workshop manual. The original T.P.S. values should be recorded for possible future reference. To set TPS values without the HD breakout box see VariReg TPS Setting for Harley-Davidsons The T.P.S. values must be set to 1995 – 1996 175 mV (+/- 25mV) 1997 – 2001 275 mV (+/- 25mV) Record the original TPS value here. ………………..mV YOU MUST ENSURE THROTTLE PLATES ARE COMPLETELY CLOSED AND NO BINDING EXISTS IN CABLES to obtain the correct value setting. 3. Reset idle screws to approximate previous settings, no need to start the engine. 4. Complete full or partial fuel tank removal as described in workshop manual. 5. Remove stock fuel pressure regulator as described in workshop manual and leave Horn removed from vehicle until after tuning, this will allow ease of access to the regulator

BMW F650 CS Front belt wheel not correctly secured

0

Filed Under (BMW) by admin on 23-11-2010

download
2.1 Removal of the front belt wheel Remove the front belt wheel in accordance with the instructions detailed in the F 650 CS Repair Manual. Remove the securing screw of the activated charcoal filter and let the filter canister hang by one side by the hoses, or remove it and lay it aside. Clean the splines and threads of the main shaft in order to remove all traces of Loctite. If necessary, remove corrosion from the main shaft spline (use only a brass bristle brush). 2.2 Visual inspection Check the splines of the main shaft for damage. Replace the main shaft if the splines are damaged (broken, chipped, bent or damaged teeth). Refer to the F 650 CS Repair Manual for this procedure 2.3 Wear check gearbox main shaft- It is extremely important that the techni- cian always check that the dimensions of the gearbox main shaft splines are to specification before proceeding with the installation of a new front belt wheel. This note only applies to motorcycles with accumulated mileage, not to new motorcycles from the crate. If the visual inspection was satisfactory and the main shaft was not replaced for visual damage, a main shaft wear check will be necessary. This check requires the use of BMW Special Tool # 23 4 571 . The adapters are designed for micrometer gauges with stud diameters from 6.35 mm to 6.6 mm. Do not use cellulose-lacquer thinners to clean the adapters as there is a risk of damaging the measuring instruments. Make sure that the micrometer gauges and the adapters are perfectly clean

BMW F 650 CS Rear belt wheel cracks Removal And Installation Manual

0

Filed Under (BMW) by admin on 12-11-2010

download
Relieve the tension of the toothed belt and lift the belt off the belt wheel (refer to F 650CS Repair Manual, 00.57). 2) Remove 6 screws (see arrow in photo at right). 3) Remove the rear belt wheel. 4) Clean and degrease the tapered bores and the threads of the mounting screws 5) Carefully place the new belt wheel in position on the damper, coat the screw threads with Loctite 243 and hand tighten the securing screws. 6) Tighten the securing screws to the specified torque maintaining a diagonally opposite tightening sequence throughout (Torque to 28 NM, curing time 12 hours). 7) Measure the vertical runout of the belt wheel (refer to F 650 CS Repair Manual, 33.15). 8) Install and adjust the rear drive belt (refer to F 650 CS Repair Manual 00.57 – 00.58) 2.1 Removal of the front belt wheel Remove the front belt wheel in accordance with the instructions detailed in the F 650 CS Repair Manual. Remove the securing screw of the activated charcoal filter and let the filter canister hang by one side by the hoses, or remove it and lay it aside. Clean the splines and threads of the main shaft in order to remove all traces of Loctite. If necessary, remove corrosion from the main shaft spline (use only a brass bristle brush). 2.2 Visual inspection Check the splines of the main shaft for damage. Replace the main shaft if the splines are damaged (broken, chipped, bent or damaged teeth). Refer to the F 650 CS Repair Manual for this procedure.

Incoming search terms: