HARLEY DAVIDSON EFI INTAKE MANIFOLD COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-04-2011

download
INSTALLATION 1. See Figure 1. Remove screw (A) that holds the air cleaner cover (B) and seal (C). 2. Remove three T27 TORX® screws (D) to release the cover bracket (E) from the filter element (F). 3. Remove the filter element, pulling the two breather tubes (G) from hole on the inboard side of element. 4. Remove the two breather tubes (G) from the fittings on the two cylinder head breather bolts (I). 5. Remove the two breather bolts (I) and O-ring seals (K) from the air cleaner backplate (J) with a 7/16 inch deepwell socket. 6. Remove the backplate and gasket (H) from the injection module. 7. Aligning the flat edge of a new cover gasket (2) with the backplate molded tab, install a gasket (2), chrome cover (1) and second gasket, in order, on the air cleaner back- plate. 8. Install the breather bolts through the air cleaner backplate. Re-install O-ring seals onto each breather bolt. Install a washer (3) from the kit on each breather bolt. Apply Loctite 243 to the breather bolts and align holes in the backplate with the holes in the cylinder heads and install the breather bolts. Use a 7/16 inch deepwell socket and alternately tighten the breather bolts to 120-144 in-lbs (13.6-16.3 Nm) . 9. Slide gasket over the sleeve on the inboard side of filter element. 10. Install breather tubes about 1/4 inch (6.4 mm) into holes on inboard side of filter element. 11. Install breather tubes onto fittings of two cylinder head breather bolts. NOTE Air cleaner mounting without installation of the breather tubes allows crankcase vapors to be vented into atmosphere in violation of legal emissions standards. 12. Place the filter element onto backplate, with the flat side down, so that the hole on the inboard side of element fits over the molded boss in the backplate. 13. Align holes in cover bracket with those in filter element and start three screws. Stamp on cover bracket points downwards. Use a T27 TORX drive head, alternately tighten screws to 20-40 in-lbs (2.3-4.5 Nm) . 14. Make sure that the rubber seal is proper seated around perimeter of air cleaner cover and place cover on back- plate. 15. Fit the air cleaner cover onto backplate. Apply Loctite 243 to the threads of air cleaner cover screw. Install screw through cover and tighten to 36-60 in-lbs (4.1-6.8 Nm)

Incoming search terms:

BMW R 1200 C And R 850 C REPAIR MANUAL

0

Filed Under (BMW) by admin on 22-11-2010

download
BMW Inspection 1000 km/600 miles I -BMW Service II -BMW Inspection III -BMW Annual Service IV Reading out MoDiTeC fault memory (Inspections I, II, III and IV) • Remove the left air cleaner trim panel. • Connect MoDiTeC to diagnostic plug. • Read out the fault memory. • Perform any repair work indicated. Checking throttle cable play, adjusting if necessary (Inspections I and III) • Check throttle cable for free movement and freedom from abrasion or kinking; renew if neces- sary. • With the steering turned to various angles, open the throttle twistgrip fully and allow it to close again. • When released, the twistgrip must return to the closed position by itself. • Pull back the protective cap. • Preset throttle cable play with the engine cold to 1.5 mm (0.06 in). • Warm the engine up to its regular operating tem- perature. • Adjust throttle cable play to 0.5mm (0.02 in) Changing engine oil, renew oil filter element (Inspections I, II, III and IV) L Note: If the motorcycle is ridden only for short distances or outside temperatures are below 0°C (32°F): change the oil and renew the oil filter element every 3 months, but at least every 3 000 km (1 800 miles). • Change the oil while it is at regular operating temperature. • Remove screw plug. • Unscrew oil drain plug and drain off oil. • Fit new seal and screw in drain plug. • Use oil filter wrench, BMW No. 11 4 650 , to unscrew and remove the oil filter. • Coat sealing ring on new oil filter element with oil and screw in. • Add oil. • Insert and tighten the screw plug. • Check engine oil level with the motorcycle in a horizontal position; use the auxiliary stand, BMW No. 001550 . e Caution: Never add engine oil above the MAX mark. X Tightening torque: Oil filter………………………………………………… 11 Nm Oil drain plug………………………………………… 32 Nm Fill quantity for engine: With oil filter change.. 3.75 l (6.6 Imp. pints/3.96 US quarts) Without oil filter change.. 3.50 l (6.2 Imp. pints/3.69 US quarts) Oil volume between MIN and MAX marks……0.50 l (0.88 Imp. pint/0.52 US quart) Engine oil grade: Brand-name HD oil for four-stroke spark-ignition engine, API classifications SE, SF, SG; combination with CC or CD specification

Incoming search terms:

2003 URAL Retro Solo Owner's And Repair Manual

0

Filed Under (Ural) by admin on 18-11-2010

download
SPECIFICATIONS GENERAL Retro Maximum speed of motorcycle 120 km/h 74 mph Reference fuel consumption at 85% of 14 km/L 33 mpg Dry mass of motorcycle 680 lb. Maximum load-carrying capacity 400 lb. Noise level below 80db OVERALL DIMENSIONS Length 2500 mm / 8 ft Width 1700 mm / 5 ft 6 in Height 1100 mm / 3 ft 6 in Road Clearance 125 mm / 5 in Seat height 840 mm / 33 in Wheel base 1470 mm / 58 in ENGINE Type 4 stroke, overhead valves, opposed twin-cylinder Displacement 745 cc Cylinder bore 78 mm Piston stroke 78 mm Compression ratio 9.0 :1 Rated horsepower 33 KW / 44.2 BHp Rated rotational speed 5600 RPM Rated torque 36 ft.-lbs @ 3750 RPM Lubrication system Dual system of forced lubrication and splashing Lubricant SAE 20W/50 CARBURETOR Carburetor type 32 CVK Keihin Number of carburetors 2 Air cleaner Paper Filter Element Lifetime JR Fuel 91 octane premium unleaded gasoline PCV Valve Internal Breather8 ELECTRICAL Ignition system 135.3734.COM-2 (CDI) Ignition coil 135.3705-2 Spark plugs NGK BP7H Ignition timing Automatic spark timer Alternator 35 amp / 12 Volt Battery Interstate #YB18L-A or equivalent Headlight Sylvania Halogen 6024, 7″ round sealed beam TRANSMISSION Clutch Dry double-disk clutch Gearbox 4 speed gearbox with reverse gear lever GEAR RATIOS I gear 3.6 II gear 2.28 III gear 1.56 IV gear 1.19 Reverse gear 4.36

Incoming search terms: