HARLEY DAVIDSON NOSTALGIC SADDLEBAG GUARD RAILS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
REMOVAL 1. If desired, remove the saddlebags. 2. Remove screws (C) and locknuts (D). Save for installation. 3. Remove reflectors with fishing line or dental floss. Use a sawing motion to remove the adhesive. Clean the surface thoroughly with an equal mixture of isopropyl alcohol and distilled water. Allow the surface to dry thoroughly. INSTALLATION 1. See Figure 1. Position the correct saddlebag guard rail (1 or 2) over the saddlebag guard and support assembly (A). Loosely install the screw (C) through the saddlebag-to- fender support bracket (B), through the saddlebag support (A) and through the inner hole of the saddlebag guard rail bracket. Install nut (D). Tighten finger-tight. NOTE Position the saddlebag guard rail as low as possible on the stock saddlebag guard and support assembly. 2. Install screws (6) and washers (5) through the clamp end of the saddlebag guard rail. Position clamp end around the upright of the saddlebag guard and install the clamp (3 or 4). Tighten screws finger-tight. 3. Align the saddlebag guard rail (1 or 2) parallel to the bottom of the saddlebag and muffler. Tighten the cap screw (C) and locknut (D) to 15-20 ft-lb (20-27 Nm) . 4. Tighten the clamp screws (6) to 22 in-lb (2.5 Nm) . NOTE The reflectors are location-specific. There are markings on the back of the reflector – “L BOTTOM” or “R BOTTOM”. 5. Peel the backing from the base of the new reflector (7 or 8). Without touching the reflector to the saddlebag guard, position the reflector and press the reflector to the saddlebag guard above the clamp (3 or 4) and press for 30 seconds. After releasing pressure, avoid direct contact with the reflector for at least 20 minutes. 6. Repeat all steps for the other side of the motorcycle. NOTE For ease of use, move the saddlebag buckles to the highest hole on the strap. 7. Install the saddlebags, if removed

HARLEY DAVIDSON CHROME FUEL TANK TRIM PANEL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
INSTALLATION 1. Refer to the Owner’s Manual and follow the instructions given to remove the seat. Retain all seat mounting hard- ware. Stop the engine when refueling or servicing the fuel system. Do not smoke or allow open flame or sparks near gasoline. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00002a) 2. See the Figure 5. Remove the original fuel filler cap (A) from the tank and set it aside. Obtain a small diameter Harley-Davidson fuel filler cap (B) and screw it into the fuel filler opening. For Model XL883C, or other models equipped with Genuine Motor Parts Large Capacity Fuel Tank 3. To ensure surface cleanliness, clean the top of the fuel tank with a mixture of 50 to 70% isopropyl alcohol and 30 to 50% distilled water. Allow to dry thoroughly. 4. Measure and mark the centerline of the fuel tank, with a wax pencil or water-based marker, at the rear of the tank as shown in Figure 3. Proceed to Step 10. For Model XL1200C 2 1 is 01910 1. Original fuel tank trim panel liner 2. Fishing line (or string) Figure 1. Removing the Existing Trim Panel (XL 1200C) 5. See Figure 1. Insert the fishing line (2) between the rear of the fuel tank and the liner (1) on the underside of the original trim panel. NOTE Raise the ends of the fishing line away from the fuel tank to avoid scuffing the tank finish 6. Using a side-to-side “sawing” motion, work the fishing line toward the front of the fuel tank to break the adhesive bond between the trim panel and the tank. 7. Carefully pull the trim panel and liner off of the tank and discard it. NOTE Be careful not to scratch the paint on the fuel tank when removing the adhesive

Incoming search terms: