Yamaha V-Star 650 Jet Kit REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 16-01-2012

download
Remove the vacuum slide from the carburetor. • Remove the OEM needle and spacer, noting the order of assembly. • Counting from the top to the bottom, install the new Baron needle clip on groove #4 of the replacement Baron adjustable needle. • Reinstall the OEM spacer and washer. • Reinstall the vacuum slide along with the diaphragm spring. • Reattach the diaphragm cover and tighten its screws. Note: Verify that the slide maintains a full range of movement! • Drain the fuel from float bowl and remove the bowl cover. • Remove the new cap head Allen screws in place of the OEM Phillips head screws. • Repeat above steps for other OEM main jet and pilot jet, and replace them with Baron’s main and pilot jets. • Thoroughly clean the inside of the float bowl prior to reinstalling it. • Reassemble the carburetor by reversing the order of previous steps. Use thecarburetor. • Locate the fuel mixture plug on each carburetor; it will either be a screw head or a brass plug. If it is a screw head, skip to step c . If you see a brass plug with a small hole in the center, proceed as follows: a. With a 5/32″ drill bit, carefully and slowly drill through the fuel mixture plug for each carburetor. CAUTION: The fuel mixture screw is located directly beneath this plug. Be prepared to stop the drill and remove the bit the instant you break through the plug. b. Insert a self-tapping sheet metal screw into the drilled hole and remove the plug. 311 #1 Industrial Way – Fallbrook, CA 92028 – USA Phone: (760) 731-1200 Fax: (760) 731-1284 E-mail: tech@baronscustom.com Website: www.baronscustom.com Included in this kit: (2) Mikuni main jets, (2) pilot jets, (2) titanium needles, (2) clips, (8) cap head Allen screws Revision 2.0 c. With air/fuel screw now accessible, use a flat blade screwdriver to turn the screw clockwise until it seats, then carefully turn it counter-clockwise 3 turns. Refer to final step for assistance in fine-tuning the setting of the air/fuel adjustment screw. • Reinstall the OEM air filter assembly. • Check all vent lines, fuel lines, and linkage for any obstructions or blockage

Yamaha YZ400/426F Camshafts REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 01-01-2012

download
Cleanliness is always a good place to start. Make sure the motorcycle is cleaned thoroughly before you start. It would be advisable to use an engine degreaser on the frame and the engine. This will ensure a clean engine during the assembly process and less of a chance of thread damage and/or dirt contamination in the engine during reassembly. And as always, replace any fiber-based gasket that was moved in any way, i.e.: cam chain tensioner. You will need basic hand tools and a torque wrench, machine towels (rags), some cleaning solvent, and a cam chain tensioner gasket. And the Hot Cams’ Degree Wheel Kit if you so desire. We will start by removing the tank and seat, top engine mount, and the cam cover. Remove the crankshaft cap and timing hole cap on the left engine case cover. Remove the spark plug. Rotate the engine in a counter clockwise (CCW) direction. Position the engine on top dead center (TDC) using the mark on the flywheel or better yet a degree wheel using a positive stop. Be sure to notice that the intake valves were the last to move, this will ensure the engine of being on “true” TDC. True top dead center occurs when both the intake and exhaust valve are closed when the piston is at TDC. This is technically the end of the compression stroke and the Page 1
beginning of the power stroke. The “artificial” TDC is during the overlap when both the intake and exhaust valves would be open. Note the positioning of the cam lobes (their included angle will be close to 170 degrees), this will help during the installation of your new Hot Cams camshafts Remove the cap bolt on the end of the cam chain tensioner block, be aware of the copper washer. Release the spring tension on the cam chain tensioner by turning the flat blade screw slot inside the adjuster block in a clockwise (CW) direction; it will lock in the retracted position. Remove the two 8mm headed bolts that hold the cam chain tensioner to the cylinder block. Remove and discard the gasket. Remove the 4 bolts that hold the exhaust cam cap in place, lift the cam cap off. It may be necessary to pry very lightly on the cap to lift it off its dowel pins. Do not use the cam lobes as the pry point. Be careful not to drop the dowels and also be careful to not lose the half moon shaped retainer for the bearing under the cam cap. Remove the 6 bolts that secure the intake cam cap and lift the cam cap off the camshaft, again, be careful to not drop the retainer or dowels. Lift the intake camshaft out of its pocket in the cylinder head casting. Remove the cam chain from the sprocket, set the stock camshaft aside. Lift the exhaust camshaft out of its pocket in the cylinder head casting and remove the chain from the sprocket. Do not drop the cam chain, dangle it over the side of the engine while keeping slight upward pressure on the chain to maintain its position on the drive sprocket on the crankshaft

Incoming search terms:

HARLEY DAVIDSON TOURING CHROME PASSENGER FOOTBOARD PAN KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-04-2011

download
Installation 1. See Service Parts illustration. Remove socket head cap- screw (2) from footboard support (3). Place support on a clean flat surface. 2. From bottom of footboard (1), use a small flat blade screwdriver to push rubber beads on pad (5) up through holes in footboard. Remove pad from footboard. 3. Using a brass drift and rubber mallet, tap two retaining pins (4) toward center of footboard and remove. 4. Remove footboard from support bracket taking care to remove and retain detent ball (6) and spring (7) from footboard support (3). 5. Insert spring (7) and detent spring (6) into footboard support (3). 6. Place new chrome footboard pan in position with footboard support and insert retaining pins using a brass drift and rubber mallet. 7. Moisten rubber beads on pad with soapy water. Place pad into position on footboard. From bottom of footboard, use needle nose pliers to pull rubber beads down through holes in footboard. 8. Engage nubs on inboard corners of pad with holes in foot- board. 9. Install socket head cap screw into footboard support and tighten 120 in-lbs (13.6 Nm). 10. Repeat procedure for other passenger footboard

HARLEY DAVIDSON DIAMOND PLATE PASSENGER FOOTBOARD INSERT KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-03-2011

download
Removing the Old Insert 1. If installed, remove the underside chrome footboard covers. 2. With the passenger footboard in the down position, slightly raise an outside “corner” of the stock rubber insert pad off the footboard with a flat-blade screwdriver. 3. From underneath the footboard, push the pad nipple through the hole with a second flat-blade screwdriver. 4. Carefully slide the first screwdriver under the pad to the other front “corner”. Repeat steps 2 and 3. 5. Pry up the inboard pad corners with the screwdriver and remove the old pad. Installing the New Insert 1. Center the two footboard pivot pins. 2. Moisten the rubber nipples, dowels and pivot pin holes on the new insert pad with soapy water to ease installation. 3. Place the insert pad into the footboard with the two extended rubber nipples over the holes. Firmly grasp the hinge side of the footboard and pad with both hands. Insert the dowels into the footboard. 4. Pull the extended nipple ends through the holes to properly seat them. Cut off the rubber “pull end” on the tip of each nipple. If so equipped, reattach the underside chrome footboard cover. Repeat all procedures for the other side. NOTE Avoid contacting chrome surfaces with abrasive materials (stones, sand, etc.) as damage will result

HARLEY DAVIDSON CHROME PASSENGER FOOTBOARD SUPPORT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
Removing Passenger Footpegs 1. Remove and discard the socket screw and lock washer attaching the existing footpeg bracket to the rear swing arm bracket. Proceed to Step 5. Removing Passenger Footboard Supports 1. For standard footboard 50613-91: See the Service Parts illustration. Tilt the footboard to the “up” position. Remove the underside chrome footboard covers if so equipped. From the bottom of the footboard, use a small flat-blade screwdriver to push the rubber beads on the pad up through the holes in the footboard pan. Remove the pad. For swept-wing (FLHRS- and FLHTCSE-style) footboards: With the passenger footboard in the “down” position, carefully raise an outside “corner” of the stock footboard insert off the footboard pan with a suitable flat-bladed tool, taking care to avoid scratching the chrome footboard pan. Continue around the edge of the footboard, using a second flat-bladed tool if necessary to pry up and remove the old insert. 2. Using a brass drift and rubber mallet, tap one pivot pin (6) out of the pivot hole into the center pocket of the footboard pan, remove the pin and set it aside. Repeat for the second pin. 3. Remove the footboard from the support bracket (1). Remove and discard the steel ball (5) and spring (4) from the hole in the bracket. 4. Remove and discard the socket head screw (2) and lock washer (3) attaching the footboard support bracket to the rear swing arm bracket. Proceed to Step 5. Installing the New Footboard Supports NOTE Three holes are available in the rear fork brackets for footboard support mounting. Depending on model and year, the footboards can be installed in any of two or three positions for passenger comfort. A plastic plug, inserted in the upper hole at the factory, can be removed. 5. See the Service Parts illustration. Position a new chrome footboard support (1) against the swing arm bracket at the desired height. The left and right supports are identical. With the locating peg on the footboard support in the next lower hole, fasten the support with a hex socket screw (2) and lockwasher (3) from the kit. Tighten the screw to 15-18 ft-lbs (20-24 Nm). 6. Place the new spring (4) into the retaining hole in the footboard support. Rest the detent ball (5) on top of the spring

Incoming search terms:

BUELL XB9R REMOVABLE SADDLEBAG KIT Installation Instructions

0

Filed Under (Buell) by admin on 03-02-2011

download
Installation 1. Ensure that the tail section of the motorcycle is clean and dirt free. 2. See the Service Parts illustration. Using a T27 TORX drive head, remove the two screws holding the tail section underside shield. 3. Install the saddlebag bracket (3) as shown, reinstall the screws and tighten securely. Federal Motor Vehicle Safety Standard (FMVSS) 108 requires all motorcycles to be equipped with side reflectors. The mounted saddlebags will cover the factory-installed rear side reflectors on these vehicles. Reposition, or have a dealer reposition, the original rear side reflectors supplied with this motorcycle or apply new ones. If this is not done, the loss of visibility to other motorists may result in death or serious injury. NOTE New reflectors (Part number 59256-84A) are available from your Buell Dealer. NOTE When removing adhesive residue, take care to keep from scratching or damaging the reflector, mounting bracket or surrounding parts. 4. Use a thin flat blade, like that on an X-Acto knife, and carefully pry the reflectors off of their mounting brackets. Remove the adhesive residue from the brackets and the back of the reflector. 5. Mount the new reflector relocation brackets (4) to the stock reflector mounting brackets as shown. Attach each relocation bracket through the slots in the stock bracket with two screws, flat washers and lock nuts from the Hardware Kit (5). Slide the relocation bracket to the rearmost position and tighten securely. 6. Remove the outer release liner of the foam tape on the relocation bracket. Mount the stock reflector squarely to the bracket, and press firmly in place. 7. Remove the passenger pillion (and pillion cover, if mounted), and set aside. 8. Position one of the saddlebags to the side of the motorcycle tail section with the Buell logo facing out, and to the rear. Hook the mounting pocket on the back side of the bag onto the saddlebag bracket mounted earlier. Repeat for the other saddlebag. 9. Bring the saddlebag straps up and over the tail sectiion. Pull the right-side straps up through the buckle eyes on the left-side straps, remove any slack and fasten the hook-and-loop material. 10. Note the points where the saddlebags and straps contact the motorcycle tail section. Two lengths of clear protective tape have been provided in the Hardware Kit. If desired, cut and fit lengths of the tape to those areas of the tail section to prevent damaging the finish. 11. Replace the passenger pillion (and pillion cover if desired). Position the front tongue on the pillion overthe saddlebag straps

Incoming search terms:

YAMAHA V-STAR 650 CRUZER EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 28-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. This Exhaust system is specifically designed for California models, before continuing be sure it is the correct system for your application. 2. Loosen clamp that connects muffler to front head pipe. 3. Remove cylinder exhaust bolts from rear head pipe that connects rear head pipe to cylinder (save for re- use). 4. Remove bolts that connect mufflers to mounting bracket. Remove complete system. Note: Assistance may be required. Page 1of 4 Y411IN Rev. 1.0 YAMAHA V-STAR 650 CRUZER EXHAUST SYSTEM, CA Model Part #31505 Tools required for installation: 1/2”, 12mm & 10mm wrenches 5mm, 6mm Allen wrenches 5/16″ nutdriver / flat blade screwdriver VANCE & HINES EXHAUST SYSTEM INSTALLATION 1. Check condition of stock exhaust gaskets. Replace if damaged or worn. 2. Install mounting bracket (stamped 370-P) in the original muffler mounting position, using two 8mm bolts (supplied)(Figure 1). 3. Mark outside surface of front and rear heat shields with location of mounting clips that are welded to the inside (Figure 2). Place each heat shield on a non abrasive surface such as a blanket or carpet. Lay each head pipe/muffler onto its respective heat shield (Figure 3). 4. Loosely install each hose clamp by feeding tail end of clamp into heat shield clip (Figure 4). Take note of clamp screw head direction (Figure 3). Screw head should be accessible when system is installed on motorcycle for adjustment purposes. Note: Do not tighten yet. 5. Install T-bolt clamp onto front muffler. Slide muffler onto front head pipe. Slide dog bone shaped nut plate (supplied) inside bracket welded to backside of front muffler. Attach muffler to mounting bracket 370-P using two 5/16″ flange bolts (supplied) engaging dog bone nut plate. Leave head pipe/muffler assembly loose at this time (Figure 4). 6. Using stock Allen bolts, carefully install rear head pipe/muffler assembly into exhaust port. (Assistance may be required). Note: Do not tighten yet. 7. Slide dog bone shaped nut plate (supplied) inside bracket welded to backside of rear muffler

Incoming search terms:

HArley Davidson Sportster Sideshots Exhaust system Installation Manual

0

Filed Under (Harley Davidson) by admin on 22-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Loosen the heat shield clamps on both the front and rear exhaust pipes. This allows easier access to the head pipe mounting nuts. 2. Remove the two head pipe mounting nuts from each flange, located at the cylinder head. 3. Remove the clamp bolt which mounts the rear head pipe to the belt drive cover bracket. 4. Remove the two bolts from each muffler body which Page 1 of 4 D465IN Rev. 1.0 Sportster Sideshots Exhaust system Part #26011 U S A Congratulations, you have purchased the finest exhaust system available for your motorcycle. Your VANCE & HINES exhaust system is designed and crafted for maximum performance, a perfect fit, a great sound and unbeatable style! Please follow the installation instructions below and if you have any questions, feel free to call our technical help line (562) 926-5291. Attention Installer: (if other than owner): Please forward this instruction sheet to the purchaser of this product. These instructions contain valuable information necessary to the end user. Tools required for installation: Wrenches – 9/16″ and 1/2″ Ratchet, 3/8″ drive and 9″ extension Torx sockets – T30 Sockets – 9/16″ and 1/2″ 3/16″ & 5/16″ Allen wrench 5/16″Nutdriver/flat blade screwdriver Snapring pliers attach the muffler bodies to the mounting bar and carefully remove both exhaust pipes from the motorcycle. 5. Remove the drive belt cover and take the bracket off the rear cover bolt, it will not be re-used. 6. Loosen the brake rod at the rear eyelet using a T30 Torx driver. 7. Remove the exhaust mounting bar, saving the three mount bolts and washers for re-use. 8. Using snapring pliers, carefully remove the flanges and circlips from the stock exhaust system. Save for re-use. Note: If circlips look bent or twisted replace them with new circlips.

Harley-Davidson Sportster 883/ 1200 Straightshot HS Exhaust system REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 19-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Loosen the heat shield clamps on both the front and rear exhaust pipes. This allows easier access to the head pipe mounting nuts. 2. Remove the two head pipe mounting nuts from each flange, located at the cylinder head. 3. Remove the two bolts from each muffler body which attach the muffler bodies to the mounting bar. 4. Remove the clamp bolt which mounts the rear head Page 1 of 4 D445N Rev. 1.0 Sportster 883/1200 Straightshot HS Exhaust system Part #17815 U S A Congratulations, you have purchased the finest exhaust system available for your motorcycle. Your VANCE & HINES exhaust system is designed and crafted for maximum performance, a perfect fit, a great sound and unbeatable style! Please follow the installation instructions below and if you have any questions, feel free to call our technical help line (562) 926-5291. Attention Installer: (if other than owner): Please forward this instruction sheet to the purchaser of this product. These instructions contain valuable information necessary to the end user. Tools required for installation: 3/16″ & 5/16″ Allen wrenches 3/16″ & 5/16″ Allen & 1/2″ sockets 3/8″ Ratchet & Extensions T30 Torx driver 1/2″ Wrench 5/16″ nutdriver/flat blade screwdriver Ft/lb. & In/lb. Torque wrenches Snapring pliers pipe to the belt drive cover bracket and carefully remove both exhaust pipes from the motorcycle. 5. Remove the drive belt cover and take the bracket off the rear cover bolt, it will not be re-used. 6. Loosen the brake rod at the rear eyelet using a T30 Torx driver. 7. Remove the exhaust mounting bar, saving the three mount bolts and washers for re-use. 8. Using snapring pliers, carefully remove the flanges and circlips from the stock exhaust system. Save for re-use. NOTE: If circlips look bent or twisted replace them with new circlips. VANCE & HINES EXHAUST SYSTEM INSTALLATION 1. Check condition of stock exhaust gaskets. Replace if damaged or worn. Vance & Hines recommends you replace your gaskets with Screamin’ Eagle gaskets part number 17048-98. 2. Install and tighten supplied mounting bracket (stamped 356-P) using stock bolts and washers (Figure 1). Torque to 30-33 Ft/Lbs. NOTE: Support the rear of the bracket during tightening to insure it is aligned with the bottom edge of the frame. 3. Re-install drive belt cover. Torque to 1 x 3/8″ bolt 30-33 Ft/Lbs. 2 x 1/4″ bolts 80-120 In/Lbs. 4. Re-install brake rod eyelet using blue thread locking compound (Loctite® 243). There is a 1/2″ clearance hole in the bracket to allow access for tightening brake rod eyelet. Torque to 120/180 In/Lbs. (Figure 1). 5. Remove header pipes and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark outside edge of each heat shield to show location of mounting clips where hose clamps will loop through (Figure 2). 6. Install circlips and flanges from the stock system onto both new head pipes.

Incoming search terms:

Harley Davidson Installing The Ride Time Ultra Progressive Tour Pak LED Tail Lights

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
Remove the light bulbs from the tail light housing by depressing the tab on the bulb socket assembly and turning counter clockwise. Remove the bulb from the bulb socket. 2. Remove the lenses from the warp-around light fixture. These lens are held in place by a non-hardening black sealant. In addition, there are three plastic alignment tabs on the lens body that clip into the lens frame. To remove the lens, insert the supplied push Stick through the hole in the back of the light bulb housing and gently but firmly push the lens outward. This action places a stress on the alignment tabs. 3 . Using a flat blade screw driver, pry the lens away from the frame at the top, side, and bottom to release the lens alignment tabs. Go back to step 2, and use the plastic tube to push the lens outward. It may be necessary to repeat the prying process and pushing process several times to remove the lens. Note: Some users have found it useful to heat the lens area with a hair dryer to soften the adhesive. Included in this kit are: Left and Right LED modules, 1 RTQC Quick Connect Accessory Cable , 2 RTV application sticks, 1 push stick, Approximately 3 inches of shrink tube, and 1 copy of instructions. Required for installation, but not included are: A tube of Permatex RTV (available at Wal-Mart), 1/8 inch drill bit, a drill, small flat blade screwdriver, other hand tools. Window/ body sealer if required to reseat lenses can be obtained at your local glass shop. Tour Pak, Harley Davidson, Electraglide, Raod King, and Ultraglide are registered trade marks of Harley David- son. Harley Davidson does not make or endorse the use of these lights. 4. When the lens begins to emerge from the frame, grasp it at the top and bottom and pull the lens from the housing using a up and down motion. Set the lens aside . Avoid having the sealant contact other surfaces. In most cases, the lens can be reinstalled without adding additional sealant . Note: Do not use RTV to reset the lens. If sealant is needed obtain a non-hardening body/windshield sealant from your local glass shop. 6. When you are comfortable with the location of the circuit board, drill a 1/8 inch hole in the back of the light housing. This hole will be used to bring the turn signal wire from the LED module into the Tour Pak. 7. Using the supplied stick, spread a thin layer of Permatex clear RTV silicone seal along the area where the circuit board will be located. Apply a similar layer to the top of the light housing. Route the turn signal wire through the 1/8″ hole and position the circuit board in the housing. Allow the RTV to cure. 5. Test fit the LED light board in the light housing.

Incoming search terms: