HARLEY DAVIDSON SPORT WIND DEFLECTOR AND WINDSHIELD KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 03-03-2011

download
HEADLAMP VISOR INSTALLATION (2004 ONLY) 1 2 is 01467 1. Headlamp 2. Headlamp bracket mounting screws Figure 1. Remove Headlamp Mounting Screws (Left Side Shown) 1. See Figure 1. While holding the headlamp (1), remove the left and right headlamp bracket mounting screws (2). 2. See Figure 5. Obtain the headlamp visor (2) from the kit. 3. See Figure 2. Orient the headlamp visor (1) between the headlamp and headlamp mounting bracket (2) and reinstall the headlamp bracket mounting screws (3) securing the visor and headlamp to the headlamp mounting bracket. 4. Refer to the Service Manual and adjust the headlamp for the correct angle. 2 1 3 is01468 1. Headlamp visor 2. Headlamp mounting bracket 3. Headlamp mounting bracket screw Figure 2. Install Visor Between Headlamp and Mounting Bracket (Left Side Shown) 1 2 3 is03212 1. “RT” or “LFT” marking 2. Hinge-pin head faces up 3. Clamp post socket faces outward Figure 3. Fork Tube Clamp and Post Identification (Right-Side Clamp Shown) WINDSHIELD INSTALLATION 1. See Figure 5. Obtain one of the lower mount kits from the windshield kit carton. Identify the fork tube clamp for right- side (RT) or left-side (LFT) installation as indicated in Figure 3. NOTE The lower grommets (4) have been pre-installed into the Lexan® windshield. 2. Insert the rounded end of the post into the socket in the fork-tube clamp, oriented as shown in Figure 5. Lining up the hole in the end of the post with the hole in the clamp. With a 3 mm hex key, fasten the post to the clamp with the flat-head screw (16) from the kit, and tighten to 6.8 Nm (60 in-lbs ). 3. Place the clamp around the correct-side fork tube with the hinge-pin head facing up. Insert the two longer screws (15) from the lower mount kit through the counterbored holes in the outboard side of the clamp, and thread the screws part-way into the tapped holes in the inboard half. 4. Position the clamp so the top surface is approximately 6 to 13 mm (1/4 to 1/2 inch) below the upper triple-tree, and the hinge pin is straight forward. With a 4 mm hex key, tighten the screws just enough to hold the clamp in posi- tion. 5. Obtain the remaining lower mount kit and repeat Steps 2 through 4 to install the clamp to the opposite fork tube. 6. Obtain the upper mount kit from the windshield kit carton. NOTE The upper grommets (4), socket assemblies (3), windshield mount caps (6) and 5 mm screws (9) have been pre-installed into the windshield. 7. Place one of the handlebar clamps (5) onto one side of the handlebar, in the straight section between the riser and the handlebar controls, oriented as shown in Figure 4. NOTE Temporarily disengage the switch harness retainer from the handlebar to allow installation of the clamp.

Incoming search terms:

HARLEY DAVIDSON HERITAGE REAR FENDER RAIL DISASSEMBLY AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-02-2011

download
DISASSEMBLY NOTE See Figure 1. Saddlebags must be removed to insert spacer (1). 1. Using a small flat head screw driver, remove rear fender tip light lens cover (A) by gently prying cover away from assembly. (There is a notch at top of cover to ease removal.) Remove and retain cover (A) and gasket (C). 2. Remove fender tip light assembly (B) by removing two screws, four star washers, and two nuts (not shown) using a #2 Phillips screw driver and a 3/8 inch wrench. Retain all hardware for reassembly. 3. Remove hole plugs from rearmost fender strut holes on both sides of fender. 4. Mark fender on both sides of bike using rear most fender strut hole as a template. Do not contact tire with drill bit when drilling fender holes. Drill bit contact with tire can lead to premature tire failure, which could result in death or serious injury. (00403f) 5. Carefully remove fender strut and drill a 11/32 inch hole through each side of fender in locations marked in Step 4. 6. Loosely reinstall fender strut (D), allowing enough room to slip spacer (1) between fender (E) and strut. INSTALLATION 1. Align rear fender rail (2) from kit with rearmost fender strut (D) mounting holes, making sure lower mounting tab (3) is inside fender (E). Place large chrome washer (4) from kit next to head of button head socket bolts (5) from kit. Insert bolt through fender rail (2), fender strut (D), spacer (1) and fender (E), in that order. Install large unfinished washer (6) from kit onto end of bolt (5). Secure assembly into place by threading locknuts (7) from kit onto ends of bolts (5) from inside of fender (E). Tighten loosely at this time. 2. Install truss head screw (8) from kit through fender (E) and rear fender rail mounting tab (3). Secure into place using small washer (9) and locknut (10) from kit. Use #2 Phillips screwdriver and a 3/8 inch wrench to tighten rear mounting assembly securely. 3. Tighten fender strut bolts (5) to 21-27 ft-lbs.(28-37 Nm) 4. Reinstall fender tip light assembly (B), gasket (C) and lens (A) using original hardware (not shown)

Incoming search terms:

HARLEY DAVIDSON SOFTAIL BACKREST KIT Installation Instructions

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
These kits are designed for use on all Softail models equipped with Sissy bar Uprights, part number 52735-85. See Service parts below for kit contents. Installation 1. With your hand, feel through the backrest material to locate mounting holes. 2. Carefully cut holes in material at mounting locations as applicable. Cut only enough material away for screw to enter backrest. 3. See Service Parts Illustration. Secure backrest (4) to sissy bar using bracket (3) and pan head screws (1). 4. Install flat head screw (2) through center hole into backrest (4). 5. Tighten all screws securely. Do not overtighten

Incoming search terms: