HARLEY-DAVIDSON TOURING TRUE DUAL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-04-2012

download
1. Remove both saddlebags and side covers from the motorcycle 2. Remove seat and place it away from the work area; disconnect battery. 3. Cover the primary housing, transmission top, and end cover near the head pipe to prevent damage. 4. Remove the bolt for the passenger floorboard that attaches it to the frame. 5. Remove the right side rider floorboard and support brackets. Loosen muffler clamps; remove the support bolts located at the rear upper portion of the mufflers. Remove mufflers from the head pipes. Unscrew clamps on the factory heat shields, and remove heat shields from the head pipes. 6. Unplug both O² sensors. Cut and remove the ZIPSTRIP that holds the front O² sensor wire to the frame. Loosen clamp on the rear exhaust pipe; remove the left side pipe, while leaving the split pipe in place. 7. Loosen clamp on crossover pipe and remove leaving right side exhaust intact. 8. Remove nuts on the flanges located at the cylinder heads. Remove the right side pipe as one unit. 9. Use snap ring pliers to carefully remove the circlips on each pipe inlet; remove

Harley davidson American Classic Straights on a 1988-2001 VLX 600 Shadow Installation Instructions

0

Filed Under (Harley Davidson) by admin on 01-03-2012

download
Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove bolts that are holding pipes at rear mounting bracket. 3. Loosen clamps at mufflers. 4. Remove mufflers. 5. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 6. Remove rear exhaust pipe assembly. 7. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 8. Remove front exhaust pipe assembly. 9. Remove exhaust-mounting bracket from frame. Hard-Krome Exhaust System Installation NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design, configuration and location. WARNING : Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessary on a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system.
1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. (See Illustration) 3. Install Front exhaust header pipe, taking care to not scratch chrome surfaces on pipe, engine or motorcycle — use masking tape as needed. 4. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 5. Install nut strip into slotted bracket of front pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 6. Carefully install rear pipe. 7. Install the two nuts to secure the flange that holds the exhaust header pipe to the rear cylinder head — DO NOT TIGHTEN NUTS! 8. Install nut strip into slotted bracket of rear pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 9. Tighten the two bolts that secure the rear exhaust header pipe flange. 10. Tighten the two bolts that secure the front exhaust header pipe flange. 11. Tighten front pipe bolts at mounting bracket. 12. Tighten rear pipe bolts at mounting bracket. 13. Reinstall foot peg assembly or floorboard. 14. If applicable to your model install foot peg relocating brackets and foot pegs as shown in illustration. 15. Before starting bike wipe off any fingerprints and grease off pipes. Start bike and check for any exhaust leaks.

Incoming search terms:

Harley Davidson KNIGHT PROWLER BELT DRIVE Installation Procedures

0

Filed Under (Harley Davidson) by admin on 28-02-2012

download
STEP 1: Place bike on suitable stand where rear wheel can be rotated in 4th or 5th gear when necessary. STEP 2: Remove front exhaust pipe. If necessary, remove as a one-piece unit. * Tip – Removing front floorboard will help a lot. STEP 3: Using easiest method – bolt cutter, etc. -remove pushrods and discard. We recommend using the S&S Quickee install pushrods and S&S roller tappets WITHOUT travel limiters. Remove tappet covers and tappets. STEP 4: Remove outer cam cover and rotate engine until timing marks are aligned together. STEP 5: Using Harley-Davidson service manual procedure, retract the outer chain tension shoe. STEP 6: Remove crankshaft and crankshaft sprocket retaining bolts using Harley-Davidson service manual procedure and tools. Continue to the next page for special instructions concerning this step with 06-DYNA & CHAIN DRIVE MODELS and also with 1999 THRU 2006 CHAIN DRIVE MODELS

YAMAHA SINGLE SIDED SWINGARM REMOVAL AND INSTALLATION MANUALS

0

Filed Under (Yamaha) by admin on 27-12-2011

download
1. Disconnect Battery 2. Lift and secure bike 3. Remove brake-side floorboard 4. Remove exhaust. 5. Remove rear fender 6. Remove front pulley cover 7. Remove wheel, pulley, and brake assembly simultaneously. Now remove front pulley from transmission. (Keep up with the stock nut and lock washer; these will be used during assembly) 8. Remove Passenger pegs; now remove the plastic covers in the frame that cover the pivot tube bolts. 9. Remove the stock shock bolts ( keep for re-assembly) 10. Remove the pivot tube bolts. 11. Remove the stock swingarmb12. Install “new” belt at this time. 13. Install supplied pivot tube, and bearings in RC swingarm. 14. Install shock bolt with red loctite in RC swingarm. (Do not tighten bolt at this time) 15. Insert supplied pivot bolts with red loctite through frame and supplied bushings into the RC swingarm. (Right side bushing has flats) 16. Torque shock and pivot bolts to factory specs. 17. Install belt adjustment bolts and single side keys into swingarm.

2002 Honda VTX 1800 R & S 3” BIG Straights Installation Instructions

0

Filed Under (Honda) by admin on 17-11-2011

download
Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove O2 sensors from each muffler and cover with supplied cap plug. 3. Loosen clamps at mufflers. 4. Remove bolts that are holding mufflers at rear mounting bracket. 5. Remove mufflers. 6. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 7. Remove rear pipe assembly. 8. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 9. Remove front pipe assembly. Hard-Krome Exhaust System Installation
NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to
replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design,
configuration and location. WARNING: Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessaryon a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system. 1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. (See Illustration) 3. Install Front exhaust header pipe, taking care to not scratch chrome surfaces on pipe, engine or motorcycle — use masking tape as needed

HONDA GL1800 DRIVER BOARD SETS WITH HEEL TOE SHIFTER INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 28-02-2011

download
Note: Read instructions thoroughly before installing. 1. Place bike on center stand. 2. Remove the two bolts that hold the stock left side foot peg bracket and remove bracket and foot peg. 2.2. 2 3. Install shifter slot over shifter peg. 4. With the longer bolts supplied, sandwich the Heel Toe Shifter plate between the frame and chrome bracket provided. 4. 5. Screw in bolts and secure tightly. Double check the tightness per service manual. 6. Replace stock peg with the driver board provided. 7. Install driver board with hardware provided. 8. Right side. Remove stock bracket and peg. Replace with chrome bracket and floorboard with stock bolts.

HONDA GL18000 DRIVER BOARDS REPLACEMENT RUBBER PADS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Remove any loose pads, remove any remaining rubber & glue using a blade screwdriver or razor blade. 2. Rough up the chrome surface with sand paper or by scratching with the tip of a screw driver. 3. Clean any remaining glue residue off using acetone solvent or nail polish remover. 4. Clean both the floorboards and the back side of the rubber pad with rubbing alcohol. 5. Using the supplied small brush and tube of 3M weather strip adhesive, apply a thin layer of glue to both the floorboard and the backside of the rubber pad or pads. Allow to dry for 10-15 minutes or until tacky to the touch. Apply a second thin coat to both surfaces and while still wet press the rubber firmly into place and keep pressure applied evenly for 45-60 seconds

PASSENGER FLOORBOARD RELOCATION ARMS FOR TRIUMPH AMERICA AND SPEEDMASTER

0

Filed Under (Triumph) by admin on 25-12-2010

download
1. If you are installing the relocation arms at the same time as floorboards install the floorboards first per their instructions. When installing the relocation arms with floorboards already installed proceed as follows. 2. Starting on the left side, fold the floorboard up. Remove the socket head bolt and nut which secures the floorboard to the motorcycles stock peg support and remove the floorboard taking notice of which holes the dowel pins are located in. 3. Install one of the 5/16″x1 Ω” hex bolts supplied thru the stock peg support from the backside (The threads of the bolt will face out towards you.) Place the two dowel pins into the holes at one o’clock and seven o’clock on the stock peg mount. Place the spacer blocks backside (stamped with an “L”) onto the bolt and align the hole with the pins. 4. Locate the relocation arm that has an “L” stamped on the backside of it. Place two of the supplied dowel pins into one of the two sets of the holes in the arm that are directly across from one another (180 degrees apart). Place the arm onto the spacer bock aligning the pins in the arm with the holes closest to six and twelve o’clock. Depending on which of the two sets of holes on the arm you chose the arm would, either be down at about seven o’clock or just below nine o’clock. These are the initial height settings and you may select which ever set is most comfortable for the passenger. Install one of the acorn nuts supplied onto the bolt and make finger tight. 5. Place the floorboard with its two dowel pins into the set of holes at the other end of the relocation arm that allows the floorboard to be horizontal or parallel to the ground. Use one of the 5/16″x3/4″ socket head bolts supplied to bolt the floorboard to the relocation arm and make finger tight. 6. Install the right side in the same manner, place the dowel pins in the holes at eleven o’clock and at five o’clock on the stock peg mount, then the spacer blocks backside (stamped “R”) onto the pins followed by the relocation arm with two dowel pins in one set of holes (180 degrees apart). Check to see that the right arm is at the same height or position as the left then install the acorn nut finger tight. Bolt the floorboard the other end of the arm using the remaining dowel pins and socket head bolt. Tighten the two bolts with the acorn nuts and the two socket head bolts securely

TRIUMPH AMERICA AND SPEEDMASTER PASSENGER FLOORBOARDS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 25-12-2010

download
1. Remove the 12mm nuts located behind the stock foot peg assemblies and remove the peg sets. 2. Starting on the left side locate the left floorboard assembly and left round chrome spacer block. These will be stamped with an” L” on the back side. Insert two of the 3/16″ x 1/2″ dowel pins supplied into the two holes where the foot peg was mounted at one o’clock and seven o’clock. Place the spacer blocks backside (stamped with the L) onto the pins 3. Place two more of the dowel pins in the holes on the outside of the block using the holes at twelve o’clock and six o’clock. Place the left floorboard assembly onto the spacer block and pins so that it is parallel to the ground or horizontal (this will be the holes closest to six and twelve o’clock on the backside of the floorboard assembly). Insert one of the 5/16″ x 2″ socket head bolts into the center-mounting hole. Place one of the 5/16″ washers, lock washers and nuts onto the bolt and make finger tight. Recheck to be sure the floorboard is parallel to the ground. 4. On the right side install two more of the dowel pins supplied into holes where the foot peg was mounted at eleven o’clock and five o’clock. Place the remaining spacers backside (stamped with an R) onto the pins 5. Place the remaining two dowel pins supplied into the holes of the spacer block at six o’clock and twelve o’clock. Place the right floorboard assembly onto the spacer block and pins so that it is parallel to the ground or horizontal (this will be the holes closest to six and twelve o’clock on the backside of the floorboard assembly). Insert one of the 5/16″ x 2″ socket head bolts into the center-mounting hole. Place one of the 5/16″ washers, lock washers and nuts onto the bolt and make finger tight. Recheck to be sure the floorboard is parallel to the ground. NOTE; if you are also installing the TA005-5 relocation arms, follow those instructions next. Finally be sure to tighten all bolts securely

TRIUMPH ROCKET III DRIVER FLOOR BOARDS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 24-12-2010

download
1. Starting on the left (shifter) side remove shifter pivot bolt (large allen head). Rotate the shifter assembly out of the way. Remove the retaining clip from the bottom of the foot peg pivot pin. Remove the pin and the foot peg. 2. Install the left floorboard in the original foot peg mounting location. (Note the L & R markings on the backside of the mounting blocks.) Place the allen bolt (supplied) through the original mount and the floorboard. It may also help to use the shank of a Phillips screwdriver in the bolthole at the same time to help align the holes. In some cases due to variances in the stock foot peg bracket it you may need to use a 25/64″ (.390) drill bit and drill thru both the bracket and the floorboards mounting block to allow the bolt to go thru. The blocks and their holes are machined to exact tolerances and is kept as close as possible to the size of the peg bracket so that there will not be any looseness or drooping of the floorboards when installed. Thread one of the Ny-loc nuts (supplied) onto the bolt and tighten securely. Reinstall shifter assembly and tighten securely. 3. Repeat for right side and re-check hardware for tightness. (The brake assembly will not need to be removed.)