HARLEY DAVIDSON ROAD KING CLASSIC FRONT FENDER SKIRT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-04-2011

download
INSTALLATION 1. Remove fasteners from stock fender skirt. NOTE Some early models have rivets for fasteners. These rivets will need to be drilled out. Drill the rivet heads to a sufficient depth to remove the head from the rivet shaft. Do not attempt to drill the rivet all the way through. This may scratch the fender?s painted surface. 2. Remove stock fender skirt. 3. Thoroughly clean the fender under the skirt. At this point it may be a good idea to wax this portion of the fender to prevent rust in the future. 4. See Figure 1. Cut the adhesive foam strip (5) into three equal parts. Remove the backing from the adhesive strips and apply adhesive on middle and two sides at the inside/bottom of the fender skirt (1). The foam strips will prevent rattling and unwanted noise. NOTE On some later FLT models, there may not be enough fender skirt support to allow the application of adhesive strips. If this is true for your motorcycle, you may install this kit without the adhesive strips. 5. Place the fender skirt in position, aligning fastener holes. 6. Install the screws (2) from the outside of the fender. Install the washers (4) and nuts (3) inside the fender. 3 2 4 1 5 is03865 1. Fender skirt 2. Screws 3. Locknuts 4. Washers 5. Adhesive foam strip Figure 1. Front Fender Skirt and Hardware

HARLEY DAVIDSON FRONT FENDER SKIRT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
1980 and later Touring •1986 and later FLSTC •1993-1996 FLSTN •2006 and later FLST This kit is not designed for FLSTF model vehicles. Kit Contents Table 1. Kit Contents Quantity Description 1 Fender skirt 6 Screw, pan head 6 Locknut, hex 6 Washer, flat 1 Adhesive foam strip (Heritage models only) INSTALLATION 1. See Figure 1. Remove fasteners (2) from stock fender skirt. Do not contact tire with drill bit when drilling fender holes. Drill bit contact with tire can lead to premature tire failure, which could result in death or serious injury. (00403f) NOTE Some early models have rivets for fasteners. These rivets will need to be drilled out. Drill the rivet heads to a sufficient depth to remove the head from the rivet shaft. Do not attempt to drill the rivet all the way through. This may scratch the fender?s painted surface. 1 5 3 2 4 is 01097 1. Fender skirt 2. Screw, panhead 3. Locknut, hex 4. Flatwasher 5. Adhesive foam strip (Heritage models only) Figure 1. Front Fender Skirt and Assembling Hardware 2. Remove stock fender skirt (1). 3. Thoroughly clean the fender under the skirt. At this point it may be a good idea to wax this portion of the fender to prevent rust in the future. 4. For Concho style and Bar and Shield style fender skirts, cut the adhesive foam strip (5) into three equal parts. Remove the backing from the adhesive strips and apply adhesive on middle and two sides at the inside/bottom of the skirt. The foam strips will prevent rattling and unwanted noise. For V-Logo style skirts, cut foam strip into three pieces; however make two slightly larger to cover the heads of the screws that hold the V-Logos in place. Use the remaining smaller piece on the middle, inside/bottom of the skirt. NOTE On some FLT models, there may not be enough fender skirt support to allow the application of adhesive strips. If this is true for your motorcycle, you may install this kit without the adhesive strips. 5. Place the fender skirt in position, aligning fastener holes. 6. Install the screws (2) from the outside of the fender. Install the washers (4) and nuts (3) inside the fender

Kawasaki Teryx 750 Roof / Windshield Kit Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
2. Installation iii) Adhere high density foam gasket to top portion of hood using marker line as centerline guide to ensure windshield panel will sit squarely onto foam after installation. If desired, install small edge trim to side edges of windshield panel and cut to suit. (Steps not shown) iv) Re-install windshield panel onto vehicle. Fasten panel with (6) #10-32 x 3/4″ Lg. screws and nyloc nuts (Fig.4) ensuring windshield panel sits firmly onto foam strip. v) Install and position roof panel onto vehicle allowing for equal spacing on either side of widshield panel edges. Once centered, carefully transfer upper windshield panel holes onto roof panel using a ¼” drill bit. (Fig. 5) NOTE: To prevent excessive rattling noise during operation, install foam strips between roof and rollcage contact points at this time. vi) Fasten roof panel to windshield panel using (6) ¼-20 x 5/8″ screws, washers and nyloc nuts (Fig.6).