Kawasaki Mule Roof 600, 610 and 4010 Trans Crew, Roof Installation Manual

0

Filed Under (Kawasaki) by admin on 02-05-2012

download
INSTALLTION INSTRUCTIONS – Mule 600/610 (4010 Trans skip to pg 4) 1. Place Roof Panel on top of UTV Roll cage and center front to back, and left to right. 2. Using Figure 1 Below – place UTV Roof Mounting Brackets around roll cage bar and using a marker, mark the position of the holes needed in the roof for each Roof Mounting bracket . Figure 1 Copyright 2007 DiamondBack Automotive Accessories, Inc. Page 3 3. Next, remove the roof from the roll cage and using a drill with 1/4″ bit, drill holes using the marks as a guide. 4. Cut (4) 3″ strips of adhesive foam and apply to roof in where mounting brackets are positioned to prevent roof rattling once mounted. Foam should run in the direction of the roll cage as shown in Figure 1 above. 5. Next, reposition the roof on the roll cage according to step 1. 6. Prior to attaching the roof mount brackets, cut the remaining adhesive foam in half and apply one section to the roof in the center of the roof where roof and each roll cage bar meet as shown in Figures 1 above. If additional tape is required to prevent rattling it can be purchased from any hardware store as window sealant foam tape. 7. Next, attach the roof mount brackets according to Figure 2. Use channel locks or pliers to hold top of carriage bolt and turn nut with 7/16″ socket.

Incoming search terms:

BUELL XB9R REMOVABLE SADDLEBAG KIT Installation Instructions

0

Filed Under (Buell) by admin on 03-02-2011

download
Installation 1. Ensure that the tail section of the motorcycle is clean and dirt free. 2. See the Service Parts illustration. Using a T27 TORX drive head, remove the two screws holding the tail section underside shield. 3. Install the saddlebag bracket (3) as shown, reinstall the screws and tighten securely. Federal Motor Vehicle Safety Standard (FMVSS) 108 requires all motorcycles to be equipped with side reflectors. The mounted saddlebags will cover the factory-installed rear side reflectors on these vehicles. Reposition, or have a dealer reposition, the original rear side reflectors supplied with this motorcycle or apply new ones. If this is not done, the loss of visibility to other motorists may result in death or serious injury. NOTE New reflectors (Part number 59256-84A) are available from your Buell Dealer. NOTE When removing adhesive residue, take care to keep from scratching or damaging the reflector, mounting bracket or surrounding parts. 4. Use a thin flat blade, like that on an X-Acto knife, and carefully pry the reflectors off of their mounting brackets. Remove the adhesive residue from the brackets and the back of the reflector. 5. Mount the new reflector relocation brackets (4) to the stock reflector mounting brackets as shown. Attach each relocation bracket through the slots in the stock bracket with two screws, flat washers and lock nuts from the Hardware Kit (5). Slide the relocation bracket to the rearmost position and tighten securely. 6. Remove the outer release liner of the foam tape on the relocation bracket. Mount the stock reflector squarely to the bracket, and press firmly in place. 7. Remove the passenger pillion (and pillion cover, if mounted), and set aside. 8. Position one of the saddlebags to the side of the motorcycle tail section with the Buell logo facing out, and to the rear. Hook the mounting pocket on the back side of the bag onto the saddlebag bracket mounted earlier. Repeat for the other saddlebag. 9. Bring the saddlebag straps up and over the tail sectiion. Pull the right-side straps up through the buckle eyes on the left-side straps, remove any slack and fasten the hook-and-loop material. 10. Note the points where the saddlebags and straps contact the motorcycle tail section. Two lengths of clear protective tape have been provided in the Hardware Kit. If desired, cut and fit lengths of the tape to those areas of the tail section to prevent damaging the finish. 11. Replace the passenger pillion (and pillion cover if desired). Position the front tongue on the pillion overthe saddlebag straps

Kawasaki Teryx Roof Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Place Roof Panel on top of UTV Roll cage and center front to back, and left to right. 2. Using Figures 1 Below – place UTV Roof Mounting Brackets on Roof and using a marker, mark the position of the holes needed for each Roof Mounting bracket . For rear of roof mounting, use existing slotted bracket and mark one hole through the factory slotted brackets as shown in Figure 2. Figure 1
Copyright 2007 DiamondBack Automotive Accessories, Inc. Page 3 Figure 2 3. Next, remove the roof from the roll cage and using a drill with 1/4″ bit, drill holes using the marks as a guide. 4. Cut (4) 3″ strips of adhesive foam and apply to roof in between holes to prevent roof rattling once mounted. Foam should run in the direction of the roll cage as shown in Figure 1 above. 5. Next, reposition the roof on the roll cage according to step 1. 6. Prior to attaching the roof mount brackets, cut the remaining adhesive foam in half and apply one section to the roof in the center of the roof where roof and each roll cage bar meet as shown in Figure 1 above. If additional tape is required to prevent rattling it can be purchased from any hardware store as window sealant foam tape. 7. Next, attach the roof mount brackets according to Figure 3. Use channel locks or pliers to hold top of carriage bolt and turn nut with 7/16″ socket.

Incoming search terms: