Honda GL 1800 FOG LAMP INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 24-11-2011

download
Disconnect the negative cable from the battery before installing this accessory. • To prevent scalding, allow the engine and cooling system to cool before installing this accessory. • The memories of the tripmeter, clock, radio andbsuspension system will be erased when you disconnect the battery. Reset the memories after reconnecting the battery. • Tighten the screws, bolts and nuts securely. • Trim the excess ends off the wire ties after attaching them to the wire harnesses. Do not allow the cut part of the wire tie to interfere with another harness or brake pipe. Using cutting pliers, cut out the marked areas from the front lower cowl. Finish the edges of the holes smooth and flat with a file. 1. Disconnect the negative cable from the battery. 2. Remove the front lower cowl and bolts as described in the Service Manual.

HARLEY DAVIDSON ENGINE GUARD-MOUNTED FOG LAMP KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
VRSC models: See Figure 3. Place the wire harness from the kit into the area in front of the battery. Do not block the air intake opening. All models except VRSC and 2004 and later XL models: See Figure 4. Install the wire harness from the kit. Place the relay in the opening of the frame under the seat area, and route the long leg of the harness forward along the frame backbone. 2004 and later XL models: See Figure 5. Remove the nuts retaining the ignition module (1) and temporarily reposition the module as shown. Place the relay in the recessed area (2) of the oil reservoir. Install the ignition module. Route the long leg of the harness along the frame backbone. CAUTION 1 WARNING -J02798 Figure 3. Install Fog Lamp Wiring Harness (VRSC Models) Place harness into this area but do not block air intake Air intake i04372 Battery Figure 4. Install Fog Lamp Wiring Harness (All Models Except VRSC. Dyna Model Shown) i02286.eps 1. Relay 2. Ground stud 3. Long leg of harness 2 1 3 2 of 6 Figure 2. Fog Lamp Wiring Harness Figure 1. Fog Lamp Schematic Ground To low beam To main circuit breaker Fuse N.O. Contact Switch Coil Fog lamp Fog lamp i01360a Relay 1. Fuse block 2. Relay 3. Connector to power 4. Ring terminals (Ground) 5. To fog lamps 6. Unterminated wire to low beam 7. Switch with boot and bracket 4 2 5 6 7 1 3 i05708 5. All 2003 and earlier models and VRSC: Cut the connector from the white power lead, and replace it with the ring terminal supplied in the kit. 6. All 2003 and earlier models, except VRSC: Connect the white wire with the ring terminal to the copper stud (BAT) terminal of the main circuit breaker. All 2004 and later models, except VRSC: Connect the white wire with connector to the B+ connector on the harness. All VRSC: Connect the white power lead to the battery positive terminal. 7. See Service Part illustration. Connect the black ground wires with the two ring terminals to the ground stud under the seat, or at any good electrical ground point. Secure the kit harness to the adjacent harnesses with cable straps (item 6) from the kit. When routing wires through the front fork, make sure the wires are clear of moving parts, to avoid pinching and possible short circuits. 8. Route the forward end of the harness past the steering head, and route the lamp switch leg of the harness along the left side of the handlebar to the clutch control. 9. See the Service Parts illustration. Obtain the switch mounting bracket (item 11) from the kit. Unscrew the boot from the lamp switch, and install the switch into the bracket. Replace the boot on the switch. NOTE If the boot becomes worn or damaged, or is lost, replace the boot to prevent moisture from entering the switch. See the Service Parts illustration (Item 12). 10. See Figure 6. Remove the lower screw (1) and washer from the clutch control clamp (3), and install the lamp switch and bracket assembly (2). Install the screw and washer and tighten to 60-80 in-lbs (7-9 Nm). 11. See the Service Parts illustration. Secure the lamp switch leg of the harness to the handlebar using the wire harness retainers already on the bike. Snap the retainers into the holes in the handlebar. 12. Remove the headlamp assembly. See HEADLAMP – REMOVAL instructions for the correct model in the Service Manual. CAUTION 3 of 6 -J02798 Figure 6. Install the Lamp Switch on the Clutch Control Clamp i04370 3 1 1. Lower clamp screw 2. Lamp switch and bracket assembly 3. Clutch control clamp 2 Figure 5. Install the Wiring Harness (2004 and Later Models) i05712 3