650 Yamaha V-Star InstaTrike REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 29-12-2011

download
install all bolts loosely until all brackets are in place y Remove any aftermarket accessories (saddle bags, back rests, etc) before hitch installation. After installation remount accessories. NOTE: Some aftermarket accessories may not be compatible with InstaTrike. 1) Place motorcycle on a firm level surface. 2) Remove rear foot pegs and bolts 3) Attach bracket A (left) and bracket B (right) to the inside of the rear foot peg bracket and reattach rear foot pegs using new bolts provided. 4) Attach front of bracket C (left) and bracket D (right) to bottom of brackets A and B 5) Attach bracket E (left) and bracket F (right) to two rear fender attachment bolts using new bolts provided 6) Attach brackets G and H to rear of brackets E and F 7) Attach bottom of brackets G and H to hitch plate. 8) Attach rear of brackets C and D to TOP of forward hitch arms. 9) Tighten all bolts. Installation Diagram Leveling stand screw jack installation 1) Thread right side screw jack into threaded hole on bracket D 2) Push motorcycle over from left side until right screw jack is touching floor. 3) Install left side screw jack on bracket C and adjust out until motorcycle will rest upright on both screw jacks. 4) Adjust screw jacks until motorcycle is level. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position

HONDA GL1800 CHROME SPORT SHIFTER INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 27-02-2011

download
1. Place bike on center stand. 2. Remove the two bolts that hold the stock foot pegs and remove foot peg. 3. Install shifter slot over shifter peg. 4. With the longer bolts supplied, sandwich the Sport Shifter plate between the peg and frame. 5. Screw in bolts and secure tightly. Double check tightness per service manual. 6. Install shifter pegs with hardware provided MOUNTING INSTRUCTIONS FOR 45-1620 GL1800 CHROME SPORT SHIFTER

HONDA GL1800 DRIVER BOARDS WITH HEEL/ TOE SHIFT INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Place the motorcycle on its centerstand. Remove the stock foot pegs and mounts (four 6mm wrench size allen screws) 2. Beginning on the left or shift side remove the rubber cover from the shift pedal. (Some WD-40 or armor all will make it much easier). Using a hacksaw cut the retaining knob off the end of the shift pedal as shown in photo #1A. Don’t worry should you ever remove the floorboards you can replace the rubber and glue it in place. 3. Install the left floorboard assembly being sure the fork in the toe-heel shifter goes over the shift pedal. Install the two original bolts and snug them. 4. Locate the black plastic shift bushing (see photo #2A) notice the set screw on the side of the bushing slide the bushing onto the shift pedal with the small diameter going on first and engaging the fork on the toe-heel shifter. The shoulder of the bushing should be touching but not putting a side force on the fork. Rotate the bushing so that the set screw is at 9 o’clock tighten the set screw. Locate the rubber cap provided and install it over the end of the stock shift pedal. (See photo #2B). 5. Next rock or pivot the floorboard assembly up and down noting the play between the bolts and bolt holes. Position the floorboard half way between these two extremes then tighten the bolts securely. Check for clearance between the bottom of the toe shifter and the floorboard (min. 1/8″) by pushing the toe shifter down until it stops while rotating the rear wheel (see photo 2C). If there is not sufficient clearance loosen the two mounting screws and pivot the floorboard to obtain the1/8″ clearance and retighten the screws. If installing the heel shifter into one of the two optional forward mounting holes check for the 1/8″ clearance while rotating the rear wheel and up shifting. 6. On the right side remove the 12mm brake pedal mounting bolt, notice the punch mark on the pedal shaft that aligns with the slot in the pedal. The pedal MUST be re-installed in the same position. Pull the pedal outward and off the shaft. 7. See photo (3). On the bottom side of the footpad make a mark ¾” from the rear and outside edge as shown. Drill a ¼” hole thru the pedal at the mark. See photo (4) lay the brake pedal extension upside down on a bench and place the stock pedal into the opening as shown, while holding the two pieces firmly together and using the hole drilled earlier as a guide drill a ¼” hole thru the bottom of the pedal extension. Turn the two pieces over, using a needle nose pliers insert the ¼” bolt provided from the top down thru both pieces, install the lock nut provided and tighten securely. Carefully align the punch mark with the slot on the pedal and re-install the brake pedal (should the shaft slide inward you will need to remove the chrome side cover and hold the shaft outward using your finger as shown in photo (5A). Install the original 12mm bolt and tighten securely

TRIUMPH ROCKET III CORBIN SADDLEBAG SUPPORTS

0

Filed Under (Triumph) by admin on 25-12-2010

download
1. Remove the 9/16″ bolts from the lower saddlebag support brackets located inside the bottom of the saddlebags. 2. Remove the passenger foot pegs and saddlebag mounting brackets by first removing the pegs pivot bolts and nuts then the 12mm nuts from the backside of the pegs. 3. Install the new saddlebag mounting brackets reusing the bolts inside the saddlebag. If you are installing floorboards and relocation arms use the 5/16″ X 2 1/2″ hex bolts supplied in place of the one supplied with the relocation arms to bolt the brackets and arms to the motorcycle. If you are installing floorboards only use the 5/16″ X 3″ socket head bolts supplied in place of the one supplied with the floorboards to bolt the floorboards and saddlebag brackets to the motorcycle. 4. Follow the instructions for the relocation arms and or floorboards