Harley Davidson FLH EZ-Steer Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 22-03-2012

download
Installation of the Champion EZ-Steer system is similar to the installation of the OEM triple clamp of your Harley Davidson FLH Motorcycle. We recommend that you use an OEM service manual and follow the prescribed disassembly, installation and torque specifications for the upper and lower clamp assembly. Before Installing Kit (2008 & Prior) The wiring bracket of the OEM upper triple clamp needs to be modified to fit the Champion upper triple clamp. After removing / disassembling the OEM parts from your motorcycle, position the OEM wiring bracket onto the Champion upper clamp as shown. Scribe the ID of the steering stem hole onto the wiring bracket and enlarge the hole to scribe line. This will allow the wiring bracket to fit over the new Stem Lock-Nut. Install OEM handle bar mount assemblies to Champion upper clamp using Item #5 (Handle Bar Mount Spacer). The spacers are used on top of the upper clamp. Installation Notes • Be sure to use the correct fork extension. Yellow 2002 and newer (non adjustable air pressure). Black for 2001 and older (adjustable air pressure). Be sure to double check the fork cap (Fork Tube Plug) being removed. • Reinstall the OEM O-rings on Item #7 (Fork Extensions) prior to installing in the fork tubes. • On some of the Road King models with chrome headlight Nacelle, Item #9 must be mounted underneath upper clamp Item #2 to ensure enough room for air fittings. • Be sure to replace fork covers in proper order, during installation of the fork tubes. • Thoroughly clean sides of steering neck and install self adhering rubber stops where steering stop screws contact frame. • Secure wires and cables clear of steering stop bolts. • Do not torque Item # 1 (½-20 x 1-1/4″ Hex Head Bolt) until fork tubes have been installed to assembly. • Note the torque specification for the items listed in the table below.

Harley Davidson 2004-Up Sportster EZ-Steer Installation Manual

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
Installation Notes • Remove front fender, wheel, brake caliper, and fork tubes. • Remove all components attached to stock triple clamps, then the triple clamps themselves. • Remove upper and lower bearings including race. • Install new steering stem bearing races into neck. • Install new upper steering stem bearing with seal into neck. • Install Top and Bottom triple clamps into neck and snug steering stem bolt with washer. • Remove fork tube cap from both forks. • Install fork extensions with o-ring into fork tubes and tighten until fully seated. • Install fork tube caps with o-rings and tighten (see torque table). • Slide fork tubes into triple clamps until the top of each tube cap extends 0.42-0.50 in. above top surface of upper triple clamp. • Tighten 3/8-16 x 1.5″ bolts on upper triple clamp (see torque table). • Tighten steering stem bolt (see torque table). • Tighten pinch bolts on lower triple clamp (see torque table). • Install front wheel assembly and front brake caliper. • Install front fender. Item # Part Description Torque Spec (Lb. Ft.) – Fork Tube Cap 22-58 8 Bolt, Steering Stem, SP 30-35 11 3/8 – 16 X 1.5″ Socket Head Cap Screw 30-35 EZ-Steer Maintenance The bearings in your EZ-Steer rake kit are normal wear items, not subject to replacement under Champion’s one year Limited Warranty for the product. Failure to follow your motorcycle manufacturer’s recommendations for periodic OEM triple-tree maintenance will accelerate the wear on these bearings. Checking/adjustment of the steering stem nut torque with the front end lifted, in accordance with your motorcycle manufacturer’s recommendations, is important to reliable bearing service. Windshield Notes Please note that this EZ-Steer kit accommodates all known windshield types with the exception of a minor modification to Quick Release Compact Windshield, example part no. 58063-04. You will need to oblong the lower bolt holes as shown in figure

Incoming search terms: