HARLEY DAVIDSON TOURING FRONT LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
REMOVAL 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to the appropriate Service Manual and remove the front forks. 3. Move forks to bench area. Place suitable drain pan on floor beneath a vise. INSTALLATION Fork Disassembly 1. See Figure 6. Remove nuts (U), lockwashers (T), flat washers (S) and axle holder (R) from studs at end of fork slider. 2. See Figure 1. Obtain FORK TUBE HOLDER (HD-41177) and proceed as follows: a. Clamp end of tool in vise (1) in a horizontal position with plastic knobs facing toward you. b. With the fork cap bolt topside, clamp fork tube between rubber pads (2) on inboard side of tool. Tighten knobs (3) until fork tube is securely held. NOTE Refer to Figure 6 for Steps 3-17. 3. Remove fork cap bolt (A) from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug (B) from fork tube (G). Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring (1) from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove screw and washer (Q) from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and save blow valve (E). 12. Remove damper tube (2). 13. Remove rebound spring (F) from damper tube. 14. Using pick tool, remove retaining clip (H) between fork slider and fork tube. 15. Remove fork tube (G) from fork slider. Slide fork tube gently in a slide hammer motion against the slider to remove the seals and bushing from slider. 16. Slide fork oil seal (I), slider spacer (J) and slider bushing (K) off end of fork tube (G). 17. Remove the lower stop (L). Fork Assembly NOTE Refer to Figure 6 for the following procedure. 1. Obtain new Damper Tube (2) from kit and install rebound spring (F) over the lower end. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube (G). Install lower stop (L) on the lower end of damper tube. 3. Install fork slider (O or N) in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (K) (45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing (K) down fork tube. 5. Slide slider spacer (J) down fork tube until it contacts slider bushing. 6. Obtain new fork oil seal (I) (45875-84A, not included). Coat fork oil seal ID with clean fork oil. With the lip garter spring side facing down (toward the fork slider), slide oil seal down fork tube until it contacts slider spacer title_tag=

Kawasaki Vulcan Front Suspension Lowering Kit Installation manual

0

Filed Under (Kawasaki) by admin on 27-02-2011

download
INSTALLATION 1. This lowering method requires replacement of the front spring spacers. This is a simple task, and is completely reversible. First, raise the front tire off of the ground before you begin. Raise the motorcycle so no weight is applied to the front wheel. 2. Cover the gas tank with a thick towel to prevent scratching. Don’t omit this…you’ll be sorry if you do! 3. If the handlebar risers are OEM (stock), loosen the handlebars in their clamps and lift them from the risers, carefully placing them on the gas tank on a thick towel to prevent scratching. This will allow room for the spring spacers to be removed from the front forks. 4. Using a small knife blade, sharp screw driver, etc. in the pinch grove on each side of the triple clamp, gently pry upwards and pop the chromed plastic covers off. These are the covers on the top of the front forks, covering the spring retainers. Below these chrome caps, you’ll find a gold anodized metal plug with a small counter bore in the center. This is the part used to retain the springs within the front fork tubes. Using an extension bar, large Phillips screwdriver, etc., press down a bit in the counter bored area of the plug to take the pressure off of the small internal “C” ring. While this “gold” colored plug is depressed, remove the internal C-ring. The C-ring is made of small diameter wire. Once the C-ring is removed, slowly release the pressure on the plug and it’ll push itself out of the top of the shock. The picture below is of the upper fork leg with the gold retaining plug removed. 5. Stick a finger into the fork tube, and slide the OEM tubular spacer up and out of the fork tube. 6. The picture below illustrates the use of a Scootworks lowering spacer with the fork spring. On the right hand end of the you’ll see a Scootworks lowering spacer. The fork spring stays in the front fork, and you’ll drop in the spacer with the desired amount of lowering. The approximate amount of lowering is marked on each Scootworks spacer. 7. Select the spacers for the desired amount of lowering. The longest spacers supplied are marked as [1] and will lower the front suspension 1″. The spacers of middle length are marked as [2] and will lower the front suspension by 2″. The shortest spacers supplied in the kit are marked as [3] and will lower the front suspension by 3″. Omission of the spacers completely will lower the front suspension by approximately 4″. 8. Install the selected spacers in the fork tubes, on top of the internal fork spring. Place the gold anodized metal plugs on top of the spacers and press them back into the fork tube. Be sure to turn the metal plug so the side with the counter bore is facing outwards. Reinstall the C-rings, and gently lower the front end back to the ground. Make sure the C-rings seat themselves in their respective grooves when the weight of the bike is placed back on the front end. Re-install the chrome caps.

Incoming search terms:

Street Fork Spring Installation Instructions

0

Filed Under (Tips and Review) by admin on 13-02-2011

download
1. Remove fork springs according to instructions contained in your shop manual. For maximum performance we highly recommend that the forks be thoroughly cleaned, inspected and new fork oil installed. Note: If your motorcycle comes equipped with two fork springs in each leg (long & short), remove and discard both springs and the flat washer between the springs. If a stock spacer exits, remove it. If there is a short spring on the damper rod, do not remove it! 2. Use the recommended fork oil viscosity as noted in your owners manual with the following exceptions: GL1100 20 weight, GL1200/1500 15 weight required. See fine tuning for more in- formation. Fork oil level/volume should be checked according to the steps outlined in your authorized shop manual. Measurement of your fork oil by level is the preferred method. However, some manuals only specify a volume measurement. Due to the design of a progressive wound fork spring it will displace more oil thus requiring a maximum oil level of 5.5″ (140mm). Caution: This is not a recommendation, it is only a precautionary statement. If your manual specifies an oil level higher than 5.5″ (140mm) set the oil level at 5.5″ (140mm). (Oil level is the distance from the top of the fork tube to the top of the oil with the fork completely collapsed and the fork spring removed see figure 1.) This measurement can be made by using either one of the Progressive Suspension Fork Oil Level Adjusters (FOL-1 or FOL-2). 3. Install your new fork springs into the forks. Mechanically, it makes no difference which way the springs are installed. Some manuals will state; install the spring with the close wound end towards the bottom. This is done because sometimes there will be less spring noise. The springs will perform exactly the same regardless of which direction they are placed. Check the spacer length requirement for your motorcycle in the enclosed supplement. If not listed, you must calculate the pre-load. What is pre-load? Pre-load is the distance the spring compresses when the fork cap is installed. You may or may not utilize a spacer to achieve proper pre-load. The spacer in itself is not “pre-load”. It just helps to achieve it. Why is pre-load important? It determines the proper ride height which in turn affects how the bike handles.

Yamaha XVS 650AN Supplementary Service Manual

0

Filed Under (Yamaha) by admin on 15-12-2010

download
MAINTENANCE SPECIFICATIONS ENGINE Item Standard Limit Connecting rod: Oil clearance Color code (corresponding size) 0.031 0.055 mm (0.0012 0.0022 in) Blue Black Brown Green CHASSIS Item Standard Limit Front suspension: Front fork travel Fork spring free length Installed length Spring rate (K1) Stroke (K1) Optional spring Oil capacity Oil level Oil grade 140 mm (5.5 in) 332.5 mm (3.1 in) 287.4 mm (11.3 in) 3.43 N/mm (0.343 kg/mm, 19.2 lb/in) 0 140 mm (0 5.5 in) No 0.507 L (17.4 US oz) 95 mm (3.74 in) Yamaha fork oil 10 WT or equivalent 325.9 mm (12.83 in) Front brake: Type Disc outside diameter thickness Pad thickness inner Pad thickness outer Master cylinder inside diameter Caliper cylinder inside diameter Caliper cylinder inside diameter Brake fluid type Single disk 298 5 mm (11.73 0.2 in) 6.0 mm (0.24 in) 6.0 mm (0.24 in) 14.0 mm (0.55 in) 30.2 mm (1.19 in) 33.3 mm (1.31 in) DOT 4 4.5 mm (0.18 in) 0.8 mm (0.03 in) 0.8 mm (0.03 in) Brake lever & brake pedal: Brake lever free play (at pivot) Brake lever free play (at lever end) Brake pedal position Brake pedal free play Clutch lever free play (at pivot) Clutch lever free play (at lever end) 1 2 mm (0.04 0.08 in) 10 15 mm (0.39 0.59 in) 108 mm (4.25 in) 20 30 mm (0.79 1.18 in) 2 3 mm (0.08 0.12 in) 10 15 mm (0.39 0.59 in) -4- MAINTENANCE SPECIFICATIONS SPEC ELECTRICAL Item Standard Limit T.C.I.: Pickup coil resistance/color T.C.I. unit model/manufacturer 182 222 Ω at 20C (68F)/Gray – Black J4T088/MITSUBISHI (U.S.A) J4T128/MITSUBISHI (CAL) Ignition coil: Model /manufacturer Minimum spark gap Primary winding resistance Secondary winding resistance F6T541/MITSUBISHI 6 mm (0.24 in) 3.6 4.8 Ω at 20C (68F) 10.7 14.5 kΩ at 20C (68F) Voltage regulator: Type Model /manufacturer No load regulated voltage Semi-conductor, short-circuit type SH650C-11/SHINDENGEN 14.1 14.9 V Rectifier: Model /manufacturer Capacity Withstand voltage SH650C-11/SHINDENGEN 18 A 200 V Electric starter system: Type Starter motor: Model /manufacturer I.D. number Output Brush overall length Commutator diameter Mica undercut Starter relay: Model /manufacturer Amperage rating Constant mesh type SM-13/MITSUBA SM-13 0.7 kW 10 mm (0.39 in) 28 mm (1.10 in) 0.7 mm (0.08 in) MS-5F-441/JIDECO 180 A 4 mm (0.16 in) 27 mm (1.06 in) Flasher relay: Type Model /manufacturer Self cancelling device Flasher frequency Wattage Semi transistor type FB257H/DENSO Yes 75 95 cycle/min 27 W 2 + 3.4 W Fuel pump relay: Model /manufacturer G8R-30Y-Q/OMRON

FC Shock Spring Installation Guide

0

Filed Under (Tips and Review) by admin on 14-12-2010

download
Installation: 1. Remove the fork springs according to the OEM Owner’s Manual. 2. Check/adjust fork oil level and weight according to OEM Specifications. Caution: Most inverted forks will not require the use of any shim washers or spacers. In cases where use is necessary with the twin chamber style fork, the shims must be placed at the bottom of the spring. Most conventional forks (non-inverted) will use shim washers or spacers at the top of the fork spring. 3. Install Factory Connection fork springs and refer to OEM Owner’s Manual for proper assembly procedures. 4. Be sure to double check all fasteners. Note: Most modern day forks require special tools for disassembly and assembly of the components. Examples : Showa 47/49mm Twin Chamber, KYB 48mm Twin Chamber, WP 07 SX Models/SXS Components. Installing fork springs is an intricate process that should be performed with extreme care by a qualified suspension technician. Failure to install the springs correctly could cause damage to one or more components of the fork. This damage, although not readily apparent, could lead to unexpected failure or rider injury. Factory Connection manufactures models specific fork springs. Installation of a Factory Connection spring not designed for your motorcycle may result in unexpected failure and rider injury. Please consult your Factory Connection spring dealer or call Factory Connection directly if you are unsure about a spring/or springs. 1. Factory Connection’s Limited Lifetime Warranty Factory Connection warrants, to the original retail purchaser (“consumer”) who retains ownership of the vehicle on which the suspension spring(s) (“products(s)”) was originally installed, all suspension springs for life against factory defects in material and workmanship (other than defects in finish) when used under normal use and operating conditions. 2. Your Remedy Upon verification of warranty coverage, Factory Connection at its option will replace defective or prematurely worn-out product (s), without charge, or refund the purchase price of the products(s). This is the Consumer’s sole and exclusive remedy for any loss or damage, however arising, due to a nonconformity or defect in the product(s). 3. Warranty Claim Procedure To make claim under this warranty, the consumer should contact the Factory Connection dealer or Factory Connection where the product(s) was purchased. Factory Connection reserves the right to test the returned product(s) to evaluate the nonconformity or possible defect. The Consumer is responsible for all costs of returning the defective or prematurely worn-out product(s) to the Factory Connection dealer as well as all costs for removing the product(s) from and installing the products(s) on the vehicle.

Incoming search terms:

2003 CM50 Owners And Service Manual

0

Filed Under (Cobra) by admin on 01-12-2010

download
Fastener ft-lb in-lb Nm Size & Remarks Cylinder head nuts 9.2 110 12 ¼” Crankcase bolts 6.6 80 9 6 x 1.0 Spark plug (SP) (SP) (SP) 14 x 1.25 Stator bolts 2.1 25 2.8 #8 Stator cover bolts 1.7 20 2.3 #8 Clutch cover bolts 5.8 70 7.9 6 mm Clutch 40 480 54 10*** Engine mount bolts 22 265 30 8 mm Swingarm Pivot 21 250 28 14 mm Intake manifold bolts 4.6 55 6.2 6 mm Ignition rotor nut 40 480 54 10 mm** Rear Sprocket Bolts 18 216 24 7 mm Rear shock mounts 40 480 54 10 x 1.5 Rear Axle Bolt 25 300 34 12 mm ** Use green (wicking / bearing retainer) thread locker, with primer, on the flywheel / crankshaft taper but none on the threads. *** Use green (wicking / bearing retainer) thread locker, with primer, on the crankshaft / clutch taper but use red (high strength) thread locker, with primer, on the nut. (SP) To apply the proper torque to the spark plug when inserting, one must first screw the spark plug in until the metal gasket ring causes resistance and then turn another 1/8 to ¼ turn. 7 Optional Components • Carburetor jets • Sprockets o Front o Rear • Seat with lower seat height, 22″ (559 mm), # TCHO0001 • Suspension Springs Weight of Rider (lb) Fork Spring Shock Spring Less than 38 (light) KCMZ0012A SCMU0321 (yellow, 320 lb/in) 38 – 45 (std) KCMZ0012 SCMU1360 (red, 260 lb/in) 46 to 55 (stiff) KCMZ0012B SCMU1380 (white, 380 lb/in) Extra stiff SCMU1400 (silver, 400 lb/in) • Suspension Valving Damping Rate Fork Valving Compression (right) Fork Valving Rebound (left) Shock Valving (kit) Soft (fast) KCMZ0033A KCMZ0032A SCMU0318A Standard KCMZ0033 KCMZ0032 SCMU031

RACE TECH SUSPENSION SERVICE TOOLS

0

Filed Under (Tips and Review) by admin on 01-12-2010

download
SHOCK SEAL BULLET TOOL “Bullet Tools” make seal head installation onto shafts quick and easy. 35-8677 TSSB12512.5 x 10mm Shock Seal Bullet 35-8678 TSSB1414 x 12mm Shock Seal Bullet 35-8679 TSSB1616 x 12mm Shock Seal Bullet FORK CAP WRENCH 46/50MM Black Oxidized steel construction for superior strength. Multiple applications (46/50mm): Honda CR250 (97-00), Suzuki RM125/250 (96-00), and removes compression adjuster assembly on Suzuki RM125/250 (98-00). Sold each. 35-8670 TFCW4650 Fork Cap Wrench SHAFT HOLDING TOOL Holds fork damping rods, cartridges, shock shafts, etc. while servicing. (aluminum) 35-8672 TFSH10 Shaft Holding Tool 10, 12, 12.5, & 14mm (Dampning Rods) 35-8673 TFSH14 Shaft Holding Tool 14, 16, & 18mm (Shock Shafts) 35-8674 TFSH20 Shaft Holding Tool 20, 24, & 29mm (20 & 25mm Fork Cartridges) 35-8675 TFSH32 Shaft Holding Tool 32 & 35mm (28 & 32mm Fork Cartridges) ULTRA SLICK SEAL GREASE Race Tech Ultra-Slick Grease provides maximum lubrication and minimum friction for all seal and bushing needs. Available in 1 oz. container. 35-8682 Ultra Slick Seal Grease SHOCK SEAL HEAD SETTING TOOL Allows easy removal and installation of all 40 – 46mm integral shock seal head assemblies. 35-8676 TFSH32 Shock Seal Head Setting Tool SAG MASTER™ The Sag Master is a tool that makes measuring “Race Sag”a snap because you read it directly. No more subtracting! Also useful in determining proper spring rates and monitoring linkage and seal drag. Comes with complete instructions and, doubles as a tape measure. 35-8681 TSSM01 Sag Master Race Sag Setting Tool FORK SPRING COMPRESSOR TOOL This unique fork spring compressor is designed to work on most current sport bikes and road racers. It allows the spring to be compressed while the fork cap is removed from the rod. It can be used on or off the bike on most models. 35-8680 TFSC01 Fork Spring Compressor Tool

2003 KING Owners / Service Manual

0

Filed Under (Cobra) by admin on 01-12-2010

download
Specifications – General Items KING Dimensions Wheelbase 39″ (991mm) Wheel size 10″ (254mm) rear, 12″ (305mm) front Seat height 26″ (660mm) Engine Type 2-stroke, single cylinder, reed valve Cooling system Liquid-cooled Displacement 49.8 cc Bore and stroke 39 mm x 41.7 mm Ignition system Electronic Spark plug Splitfire SF406B Gap 0.023″ – 0.025″ (0.58 – 0.64 mm) Ignition timing 0.050″ (1.3 mm) Before To Dead Center (BTDC) Fuel type Sunoco MO2 X or 93 octane pump gasoline OTHER RACE FUELS ARE NOT RECOMMENDED Oil type Cobra Venom 2-cycle Race Oil Fuel / oil mix ratios Between 32:1 and 40:1 (after engine Break-In is complete) Carburetion 19 mm Dell’Orto Main Jet 94 Slow (Pilot) jet 65 Float Height 16mm + 0.5mm (0.63″ + 0.020″ Transmission Speed Single Clutch Cobra 3 shoe Final drive ratio 13/39 T Chain 100 links 420 Transmission / clutch oil type Cobra Venom 3 Shoe Clutch Milk, or Dexron III Quantity 235 ml (8.0oz) 5 Chassis Front tire 2.50 – 12 Pressure 15 psi minimum Rear tire 2.75 – 10 Pressure 15 psi min. (20 psi for hard pack or rocky conditions) Front fork Cobra 30mm USD Fork oil type SAE 5 weight Fork oil amount 118 ml (4.0 oz) Optional Components • Carburetor jets • Sprockets o Front o Rear • Suspension Springs Weight of Rider (lb) Fork Spring Shock Spring Less than 51 7 lb/in, KCKG0007 SCKGOH10 (yellow, 175lb/in) 51 – 60 9 lb/in, KCKG0009 SCKGOH85 (gray, 185 lb/in) Greater than 60 12 lb/in, KCKG1200 SCKG0H, (white, 195 lb/in) • Suspension Valving Damping Rate Fork Valving Compression (base valve) Fork Valving Rebound (mid valve) Shock Valving (kit) Soft (fast) KAKG0013 KAKG0016 SCKGOH24A Standard KAKG0014 KAKG0017 SCKGOH24 Hard (slow) KAKG0015 KAKG0018 SCKGOH24B • Cobra BIG AIR SX Fork Kit part #KKKG2003 6 Specifications – Torque Values Torque Value Fastener ft-lb in-lb Nm Size & Remarks Cylinder head nuts 9.2 110 12 ¼” Crankcase bolts 6.6 80 9 6 x 1.0 Spark plug (SP) (SP) (SP) 14 x 1.25 Stator bolts 2.1 25 2.8 #8 Stator cover bolts 1.7 20 2.3 #8 Clutch cover bolts 5.8 70 7.9 6 mm Clutch 40 480 54 10*** Front axle nut 25 300 34 12 x 1.25 Front brake caliper Engine mount bolts 22 265 30 8 mm Swingarm Pivot 21 250 28 14 mm Intake manifold bolts 4.6 55 6.2 6 mm Rear Axle Bolt 25 300 34 12 mm Rear Sprocket Bolts 18 216 24 7 mm Fork cartridge rod 12 144 16 Triple clamp bolts 6 72 8 6 x 1.0 Fork cap 5 60 6.7 1.25″ x 18 Ignition rotor nut 40 480 54 10 mm** ** Use green (wicking / bearing retainer) thread locker, with primer, on the flywheel / crankshaft taper but none on the threads.

HARLEY DAVIDSON FL SOFTAIL PROFILE LOW FRONT SUSPENSION KIT INSTALLATION

0

Filed Under (Harley Davidson) by admin on 30-11-2010

download
Fork Spring Removal 1. Elevate and support the vehicle so the front tire is off the floor and the forks are fully extended. 4 9 3 1 10 11 2 5 6 7 8 is04004 1. Slider tube cap 2. Spacer washer 3. Oil seal 4. Clamp bolt and washer 5. Fork tube plug 6. O-ring 7. Fork spring 8. Tight-wound end of spring 9. Fork slider tube 10. Fork slider 11. Drain screw and washer Figure 1. Front Fork NOTE Remove the brake caliper from the fork slider. DO NOT remove the brake line from the caliper. 2. Remove the front wheel. See FRONT WHEEL: FLSTC/FLSTF/FLSTN in the Service Manual. 3. Remove the front fender. See FRONT FENDER in the Service Manual. 4. See Figure 1. Remove the slider tube cap (1), spacer (2) and oil seal (3) from the top of one fork side. Save the cap and spacer. The oil seal can be discarded. 5. Loosen the clamp bolt (4) and pull the fork from the brackets. 6. Repeat Steps 4 and 5 for the other fork side. -J00280 1 of 4 Wear saf ety glasses or gog gles when ser vicing f ork assembly. Do not remove slider tube caps without relieving spring preload or caps and springs can fly out, which could result in death or serious injury. (00297a) NOTE Be careful not to damage the O-ring. 7. See Figure 1. Remove the fork tube plug (5) and O-ring (6). Pull the spring (7) out of the slider tube (9). Remove the drain screw and washer (11), and drain the fork. Reinstall the drain screw and washer, and tighten to 52-78 in-lbs (5.9-8.9 Nm). 8. Repeat Step 7 for the other fork side. NOTE The Profile® Low Front Suspension Kit requires a different amount of H-D TYPE E FORK OIL than is listed in the Service Manual. NOTE Measure the oil level from the top of the fork tube with the fork spring removed and the fork fully compressed. 9. See FRONT FORK OIL in the Service Manual, but substitute the measures below. Fill the forks with Harley- Davidson TYPE E FORK OIL: • 1986 through 1999 models: •11.7 oz (345 cc) of oil, or •5.2 inch (132 mm) from top of oil level to top of tube. • 2000 and later models: •13.4 oz (396 cc) of oil, or •4.1 inch (104 mm) from top of oil level to top of tube. Fork Spring Installation 1. Insert a new Profile Low spring (7) from the kit into each slider tube (9), with the tight-wound portion (8) toward the bottom of the fork slider. NOTE Be careful not to damage the O-ring. 2. Install the fork tube plug (5) and O-ring (6) assembly into the slider tube and tighten securely. Be sure that one flat on each fork tube plug faces toward the inside of the fork. 3. Insert both fork side assemblies up through the slider covers, the fork stem and bracket, and the upper bracket. 4. Obtain two new oil seals (3), H-D Part Number 45733-48, and the spacer washers (2) and slider tube caps (1) saved earlier. Place an oil seal, followed by a spacer washer, onto each fork tube plug. 5. Insert the threads of a slider tube cap through each washer and seal, and into the fork tube plugs. Tighten to 40-60 ft- lbs (54.2-81.3 Nm). 6. Tighten the fork stem bracket clamp bolts (4) to 30-35 ft- lbs (40.7-47.5 Nm). 7. Install the front fender. See FRONT FENDER in the Service Manual. Install the front wheel and brake caliper. See FRONT WHEEL: FLSTC/FLSTF/FLSTN in the Service Manual. Jiffy Stand Removal/Installation 1. Move the jiffy stand to the retracted (up) position. Wear safety glasses or goggles when removing or installing spring. Spring tension can cause spring, attached components and/or hand tools to fly out which could result in death or serious injury. (00477c) 2. See Figure 3. Unfasten the jiffy stand leg spring (A) from the vehicle. Remove the hex bolt (B), lock washer (C), flat washer (D) and leg stop (E) from the threaded end of the jiffy stand leg. Discard the jiffy stand leg, but retain all other components. 3. Clean and inspect the jiffy stand attaching parts and mounting bracket for wear or damage. If parts replacement is necessary, refer to the Jiffy Stand section of your Service Manual for replacement procedures

YAMAHA XVS 650AK Supplementary Service Manual

0

Filed Under (Yamaha) by admin on 18-11-2010

download
Dimensions: Overall length Overall width Overall height Seat height Wheelbase Minimum ground clearance Minimum turning radius 2,450 mm (96.5 in) 930 mm (36.6 in) 1,105 mm (43.5 in) 710 mm (28.0 in) 1,625 mm (64.0 in) 145 mm (57.1 in) 3,400 mm (133.9 in) Basic weight: With oil and a full fuel tank 247 kg (544.5 lb) Bulb wattage quantity: Headlight Tail/brake light Front turn signal/position light Rear turn signal light Meter light Neutral indicator light High beam indicator light Turn indicator light Engine indicator light 12 V 60 W/55 W 1 12 V 8 W/27 W 1 12 V 27 W/8 W 2 12 V 27 W 2 12 V 1.7 W 1 12 V 1.7 W 1 12 V 1.7 W 1 12 V 1.7 W 1 12 V 1.7 W 1 ENGINE Item Standard Limit Connecting rod: Oil clearance Color code (corresponding size) 0.031 0.055 mm (0.0012 0.0022 in) Blue Black Brown Green CHASSIS Item Standard Limit Front suspension: Front fork travel Fork spring free length Installed length Spring rate (K1) Stroke (K1) Optional spring Oil capacity Oil level Oil grade 140 mm (5.5 in) 332.5 mm (3.1 in) 287.4 mm (11.3 in) 3.43 N/mm (0.343 kg/mm, 19.2 lb/in) 0 140 mm (0 5.5 in) No 0.507 L (17.4 US oz) 95 mm (3.74 in) Yamaha fork oil 10 WT or equivalent 325.9 mm (12.83 in) Front brake: Type Disc outside diameter thickness Pad thickness inner Pad thickness outer Master cylinder inside diameter Caliper cylinder inside diameter Caliper cylinder inside diameter Brake fluid type Single disk 298 5 mm (11.73 0.2 in) 6.0 mm (0.24 in) 6.0 mm (0.24 in) 14.0 mm (0.55 in) 30.2 mm (1.19 in) 33.3 mm (1.31 in) DOT 4 4.5 mm (0.18 in) 0.8 mm (0.03 in) 0.8 mm (0.03 in) Brake lever & brake pedal: Brake lever free play (at pivot) Brake lever free play (at lever end) Brake pedal position Brake pedal free play Clutch lever free play (at pivot) Clutch lever free play (at lever end) 1 2 mm (0.04 0.08 in) 10 15 mm (0.39 0.59 in) 108 mm (4.25 in) 20 30 mm (0.79 1.18 in) 2 3 mm (0.08 0.12 in) 10 15 mm (0.39 0.59 in)