HARLEY DAVIDSON XL (Sportster) ENGINE GUARD INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-04-2011

download
Installation- Late 1984 and Later XLModels (Equipped With Alternator) 1 CAUTION Late 1994 and 1995 XL vehicle nut plates have 3/8-16 threads. Reuse original screws on late 1994 and 1995 XL models. Installing the 3/8-24 x 1-1/4 in. screws from kit will damage nut plate and screw threads. 1. See Figure 1. From underside of steering head remove screws (7, 8, or 9) and flat washer (6). Discard original screws (7, 8, or 9) and washer (6). 2. Remove and discard the two top motor mount screws, washers, and nuts. 3. See Figures 1 and 2. Place washer (2) on 5-1/2 in. long screw (1). Insert screw (1) through one motor mount, through spacer (11) (unless engine guard is being installed on a vehicle equipped with forward controls, in which case DO NOT USE SPACER), through the offset end of bracket (3), and (with large offset toward jiffy stand side of vehicle) through the other motor mount. Place kit supplied washer (2) on end of screw (1) and secure with locknut (4). Be sure bracket does not pinch wiring. On 1986 and later models be sure bracket does not contact oil pressure switch. 4. See Figure 1. Position engine guard (5) upper mounting bracket under the steering head

HARLEY DAVIDSON HEEL REST KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-04-2011

download
Models Kit 50227-01 is designed for forward controls and fits: •1989 and later FX Softail Models with Original Equipment (OE) Forward Controls, •1993 through 2002 FXDWG, •Dyna models equipped with Forward Control Kit 49080- 93 or 49080-93A. Kit 50227-01 does not fit Dyna models equipped with Forward Control Kit 49080-03 or Forward Control Footrest Support 33695-03 (left) or 33697-03 (right). Kit 50236-01 is designed for mid controls and fits: •all 1990 and later Dyna Model Motorcycles with Original Equipment (OE) Mid Controls. Additional Parts Required Proper installation of this kit also requires installing a pair of Heel Rest Pegs, or Shifter Pegs, which can also be mounted as heel rests. Refer to the appropriate Parts Catalog for stock shifter pegs, sold separately. The current Harley-Davidson Genuine Motor Accessories and Parts catalog also has a selection of Heel Rest Pegs or Shifter Pegs and matching Footpegs. Any shifter peg style that is symmetrical in design can be used as a left or right side heel rest. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE A Service Manual for your model motorcycle is available from a Harley-Davidson Dealer. Kit Contents See Figure 1 and Table 1. INSTALLATION NOTE See Figure 1 for the following procedure. 1. Remove the screw (B), lock nut (C) and spring washer (E) securing the left footpeg to the footrest support bracket (A). Save the hardware for later installation. NOTE Heel rest levers are side-specific. Levers mount so the set screws are on the underside. 2. Obtain a Heel Rest Peg or Shifter Peg (D) (purchased separately) and the left side heel rest lever (3). Apply Loctite® 243 (7) to the threads of the peg and install it to the left heel rest lever. 3. Obtain the screw (B), spring washer (E) and lock nut (C) removed in step 1, and the heel rest lever and peg assembly (D). Position the lever assembly to the desired angle on the mount, and slide the lever assembly with the spring washer into the footrest support bracket as shown. NOTE Splines on the lever and mount provide for a limited range of heel rest angle adjustment. For Kit 50227-01. The heel rest lever (3) can be adjusted after the mount (1) is attached but before the set screw (2) is installed. Slide the lever inward off the spline, and rotate it to the desired angle. For Kit 50236-01. The heel rest lever (3) angle cannot be adjusted after the mount (1) is attached without removing them from the footrest support bracket (A). Check to ensure the heel rest (D) is in a comfortable position before tightening the mounting hardware. 4. Install the original screw (B) and lock nut (C) to secure the heel rest assembly to the footpeg mount. Tighten to 33 ft- lbs (45.6 Nm). 5. Obtain a screw (6), spring washer (5) and nut (4) from the kit. Install the footpeg to the heel rest assembly and tighten to 33 ft-lbs (45.6 Nm). 6. Obtain a set screw (2) from the kit. Apply Loctite® 243 (7) to the threads, and install the set screw to the heel rest lever. Tighten to 16 in-lbs (1.8 Nm). 7. Perform Steps 1 through 6 for the right side. USE

Incoming search terms:

HARLEY DAVIDSON AIRFOIL RIDER HEEL REST KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-04-2011

download
1989 and later FX Softail Models with Original Equipment (OE) Forward Controls, •1990 and later Dyna models (except 2003 and later FXDWG), •Dyna models equipped with Forward Control Kit 49080-93 or 49080-93A. Kit 50227-01 does notfit Dyna models equipped with Forward Control Kit 49080-03or Forward Control Footrest Support 33695- 03 (left) or 33697-03 (right). Proper installation of this kit also requires installing a pair of Airfoil Foot Rests, Part Number 50133-95 (large) or 50134- 95 (small), not included in this kit. Airfoil Foot Rests are available from your Harley-Davidson Dealer. See the Service Parts illustration for kit contents. The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have your Harley- Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. NOTE A Service Manual for your motorcycle is available at your Harley-Davidson Dealer. Installation NOTE When performing the following step, note the location and orientation of the spring washer when removing each footrest. 1. See Figure 1. On the right side of the motorcycle, remove the fastener securing the footrest to the footrest bracket. Save the hardware for installation. NOTE On motorcycles equipped with Airfoil Foot Rests, remove the adjusting screw fastening the foot rest to its footrest mount. Save the foot rest and screw for heelrest installation. 2. Fasten the Airfoil Rider Heel Rest mount and spring washer to the footrest bracket using the hardware saved from step 1. Tighten the fastener to 19 ft-lbs (26 Nm). 3. See Figure 2 and the Service Parts illustration. Place the right-side Airfoil Rider Heel Rest (2) on the Airfoil Rider Heel Rest mount (3), positioning the heelrest at the desired angle

Incoming search terms:

HARLEY DAVIDSON ENGINE GUARD KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
This kit fits 1991 and later Dyna Glide models except Dyna models equipped with forward controls, 1993 and later FXDWG, 1994 and later FXDS Dyna Convertible models Installation The slider tubes on the front forks of some motorcycles may require adjustment to prevent the front fender from contacting the engine guard at full fork compression. 1. Check that the top of tube cap on each front-fork slider tube is positioned 0.42 – 0.50 in. (10.7 – 12.7 mm) above the top surface of the fork upper backet. Adjust slider tube position if necessary. See the FRONT FORKS section of your service manual. 2. Remove the highway footpegs and side plates. Retain the footpegs and mounting hardware, including footpeg supports. Discard the side plates and plate-mounting hardware. 3. See Figure 1. Position the engine-guard top mounting plate on the engine-side of the frame upper crossmember. Fasten the guard to the frame using the hardware from this kit as shown. Do not tighten at this time. 4. On each side of the engine guard, insert two socket- head tapping screws with lockwashers from this kit through the two lower mounting holes in the engine- guard lower side plates and into the threaded holes in the frame lower-side bracket. 5. Torque the mounting hardware in steps 2 and 3 to 33 ft- lbs (44.7 Nm).

Yamaha Road Star Forward Control Kit Installation Instructions

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Before starting to assemble this forward kit on your motorcycle check the packing list to make sure that the kit you received is the correct one for your model motorcycle and that the foot pegs are the style you ordered (billet or ISO). Next check the contents hardware kit P.N.0109-1000 against the packing list for completeness. Installing The Shift Control Photo 1 Remove wires from horn. Remove the two hex head bolts (Save for later installation) that mount the OEM shift controls to your motorcycle. Unthread stock shift rod at trans shift arm, leaving OEM rod end connected to stock shift arm. Using Original Metric hardware, place a drop of Loctite #242 (blue) to the bolt threads and mount the shift control plate to the motorcycle frame, Photo 2. FORWARD CONTROL KIT PM SHIFT CONTROL ASSEMBLY Note Before torquing the shift control mounting bolts down, tighten them snug and look behind the shift control mounting plate to where it contacts the mounting lug on the frame. Make sure it fits squarely to the lug before proceeding further. Torque the two shift control mounting bolts down to 25 ft-lb. Using a 3/8″ x 1″ hex head bolt with a lock and flat washer put a drop of Loctite #242 (blue) on the threads and insert the bolt through the rear of the control mounting plate and attach the foot-peg pivot to it. Tighten the bolt while holding the footpeg pivot so that its hinge is lined up in a 45˚ rear facing angle. Thread supplied shift rod coupler to stock shift rod end at trans arm. Mount the shift pedal to the other end of the shift ro d using a 5/16″ x 1″ socket head screw and Nylocnut . Adjust the transmission shift linkage so that the shift arm on the forward controls and the shift arm on the transmission are parallel. Secure it with the jam nuts. Apply a drop of Loctite #242 (blue) to the threads under the jam nut before tightening see Photo 3 After you have assembled the shift control onto your motorcycle you must align the footpeg. The folding footpeg assembly uses a blind stud to attach the footpeg to the footpeg pivot. Shim washers (3/8″ x .015″) are used on the stud between the footpeg and the pivot, see Photo 4, so that the top surface of the footpeg is correctly aligned for your foot when it is tightened down on the pivot. This is done by setting a couple of shim washers on the footpeg mounting stud “A” and then screwing the footpeg onto the mounting stud, if the footpeg is rotated to far forward then add another shim washer, if not far enough then remove a shim washer. After you have the selected the correct number of shims for your footpeg, disassemble the footpeg and put a drop of Loctite #271 (red) on both ends of the stud and reassemble the footpeg. This will also need to be done on the brake control footpeg. Setting Up the Master Cylinder The master cylinder pushrod return spring and pushrod boot must be installed on the master cylinder before it is assembled onto the forward control mount. The parts are shown in Photo 5: pushrod boot (A), pushrod return spring (B), spring seat washer (C), and master cylinder (D). Place the return spring seat washer into bore of master cylinder so that is sits on top of the piston retaining snap ring. Next set the pushrod return spring on the seat washer and slide the pushrod boot over the return spring now slip the big end of the boot over the flange on the master cylinder so that the ridge on the inside of the boot fits into groove “A” that is machined into the end of the master cylinder flange, see Photo 6. Installing The Brake Control Unplug stock brake light switch at master cylinder. Remove brake line from rear caliper. Remove the existing brake controls from your motorcycle down to the control mounting lug that is welded on to the frame’s right side, see Photo 8. Save Metric hardware for later use. A Shim Washer PHOTO 4 A B C D PHOTO 5 A PHOTO 6 PHOTO 7 Note For complete brake system removal instructions and precau – tions refer to the appropriate service manual for your year and model motorcycle

Incoming search terms: