HONDA CT110 OWNERS MANUAL

0

Filed Under (Honda) by admin on 22-04-2011

download
ENGINE OIL Engine Oil Level Check Check the engine oil level each day before riding the motorcycle. The level must be maintained between the upper (2) and lower (3) marks on the dipstick (1). 1. Start the engine and let it idle for a few minutes. 2. Stop the engine and hold the motorcycle in an upright position on firm, level ground. 3. After a few minutes, remove the oil filler cap/dipstick, wipe it clean, and reinsert the dipstick without screwing it in. The oil level should be between the upper and lower marks on the dipstick. 4. If required, add the specified oil up to the upper level mark. Do not overfill. 5. Reinstall the oil filler cap/dipstick, check for oil leaks. CAUTION Running the engine with insufficient oil can cause serious engine damage. TYRES Proper air pressure will provide maximum stability, riding comfort and tire life. Check tire pressure frequently and adjust if necessary. NOTE Tire pressure should be checked before you ride while the tyres are cold. Select the right replacement tire in accordance with the following specifications: Cold tire pressures kPa ( kg/cm2, psi ) Front: 175 ( 1.75, 25 ) Rear : 225 ( 2.25, 33 ) Tire size Front: 2.75 – 17 41P Rear : 2.75 – 17 41P Check the tires for cuts, embedded nails, ore other sharp objects. See your authorized Honda Dealer for replacement of damaged tires or punctured inner tubes OPERATION PRE-RIDE INSPECTION WARNING If the Pre-ride Inspection is not performed, serious damage or an accident may result. Inspect your motorcycle very day before you ride it. The items listed here will only take a few minutes to check, and in the long run they can save time, expense and possibly you life. 1. Engine oil level – add engine oil if required. Check for leaks. 2. Fuel level – fill the fuel tank when necessary. Check for leaks. 3. Brakes – check operation. Adjust free play if necessary. 4. Tyres – check condition and pressure. 5. Drive chain – check condition and slack. Adjust and lubricate if necessary. 6. Throttle – check for smooth opening and full closing in all steering positions. 7. Lights – check that headlight, tail/brake light, turn signals, indicators. 8. Engine stop switch – check for proper function. 9. Battery electrolyte – check the level and add if necessary Correct any discrepancy before you ride. Contact your authorized Honda dealer for assistance if you cannot correct the proble

Incoming search terms:

TRIUMPH AMERICA AND SPEEDMASTER HANDLEBAR RISERS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-01-2011

download
1. Place a blanket folded several times over the fuel tank to help prevent any damage during the installation of the risers. Loosen the two 14mm riser mounting nuts located on the bottom side of the upper steering head. Loosen the four handlebar top clamp 6mm socket head screws. 2. It will help having a second person to hold the handlebars while you change the risers. Remove the four screws from the clamps and then remove the clamps. Pull the handlebars up off the risers, pull them back and rest them on top of the blanket. 3. Remove the nuts from the bottom of the risers and remove the risers carefully without allowing the risers to rotate, as this will scratch the clear coating on the upper steering head. Using the bolts, lock washers and washers supplied install the new risers making the bolts finger tight only. (NOTE; again, take care not to allow the risers to rotate as this will scratch the clear coating on the upper steering head). 4. Place the handlebars back up onto the new risers. Install the new top clamps supplied using the four M8 X 30mm socket head screws supplied. Set the height of the handlebars to the desired position, tighten the front bolts first and then the rear securely. (15-18 ft. lbs.) (There should be no gap between the riser and clamp at the front side) Tighten the two riser mounting bolts securely. (20-25 ft. lbs.). 5. Turn the handlebars all the way to the left and then right checking for any pulling or binding of the wires, hoses or cables. YOU MUST! Check to see that the throttle returns freely on its own when the handlebars are at full left and full right turn THIS STEP IS VERY IMPORTANT FOR OBVIOUS SAFETY REASONS! If you have a windshield installed it may be necessary to reroute the throttle cables, wires or hoses around the other side of the windshields mounting hardware to obtain adequate free play and free throttle return. You may also wish to remove the plastic clips or cable tie which secure the wiring to the handlebars and secure them to the brake hose and clutch cable (not the throttle cables) for a cleaner appearance

Incoming search terms:

Triumph Rocket III Touring HANDLEBAR RISERS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-01-2011

download
1. Place a blanket folded several times over the fuel tank to help prevent any damage during the installation of the risers. Using a small screwdriver pry out the plastic caps covering the handlebar clamp bolts. 2. Reroute the clutch cable behind the steering head as follows. Remove the clutch cable from the lever and perch. To do this first loosen the cable adjuster lock nut and then the adjuster as far as possible to give its maximum free play. Align their slots with the slot in the perch so that the cable may slide out. Standing in front of the handlebars grasp the clutch cable firmly trying to pull it out of the adjuster with one hand while pulling in the lever with the other hand. Now release the lever rapidly. Repeat several times if needed while keeping outward tension on the cable until the cable is out of the adjuster then slide it out thru the slots and remove the cable end from the lever. Reroute the clutch cable behind the steering head this will allow the additional slack needed when moving the handlebars back with the new risers (see photo). Replace the cable into the perch in the same manner. 3. It will help having a second person to hold the handlebars while you change the risers. Remove the four Allen bolts from the clamps and then remove the clamps. Pull the handlebars up off the risers, pull them back and rest them on top of the blanket. 4. Remove the Allen bolts from the center of the risers while holding the 14mm nut on the bottom side of the steering head with a wrench. Remove the risers leaving the large washer on the top side of the steering head in place. Using the bolts and lock washers supplied and the original heavy or thick washer install the new risers making the bolts finger tight only. 5. Place the handlebars back up onto the new risers. Install the new top clamps supplied using the four Allen bolts remover earlier. Set the height of the handlebars to the desired position, tighten the front bolts first and then the rear securely. (15-18 ft. lbs.) (There should be no gap between the riser and clamp at the front side) Tighten the two riser mounting bolts securely. (20-25 ft. lbs.). Replace the plastic bolt caps.

Motorcycle Derived Steering / Suspension Systems

0

Filed Under (Tips and Review) by admin on 29-11-2010

download
1. Examine the handlebars and fork yokes. 2. Turn the steering from lock to lock with the steered wheel both on a turning plate and clear of the ground. Cont’d Reason for Rejection 1. A handlebar or fork yoke a. deformed b. fractured c. cracked d. excessively corroded e. clamps not tight, or any bolt loose or missing f. handgrips missing or not secure to handlebars g. handlebar flexible mounting excessively deteriorated. 2. a. any fouling or restriction of the free movement of the steering from lock to lock b. handlebar grip/s or handlebar mounted control/s have no clearance with any other part of the machine when the steering is placed on either full lock c. steering movement excessively stiff or rough Reason for Rejection 5 does not apply to fork gaiters or shrouds. . Cont’d Method of Inspection 3. Examine the steering damper. 4. Examine the steering head bearings. 5. Examine the front fork assembly. Cont’d Reason for Rejection 3. A steering damper a. insecure b. ineffective c. impairing the steering action. 4. Excessive free play in the steering head bearings. 5. A fork assembly component which is a. missing b. loose c. cracked d. excessively bent, misaligned, corroded, worn, or has excessive free play between the sliding members of the forks, the pivot bearings or bushes e. restricted in operation f. fouling

Incoming search terms:

1985 Yamaha SRX250 REPAIR MANUAL

0

Filed Under (Yamaha) by admin on 21-11-2010

download
FILTER/FRONT AND REAR BRAKE AIR FILTER 1. Remove: °Right side cover ‘Air filter case cover ‘Air filter guide ’Air filter element ® op The engine should never be run without the air/filter element installed; excessive piston and/or cylinder wear may result. 2. lnspect: ‘Element Contamination->Clean element with solvent NOTE: A. o . After leaning, remove the remaining solvent by squeezing the element. 3. Apply: ‘SAE i0/V30 motor oil (to the elementi NOTE: . or o . .. Sqeeze out the excess oil. Element should be wet but not dripping. FRONT AND REAR BRAKE Front Brake Lever Free Play Adjustment Proper lever free play is essential to avoid ex- cessive brake drag

Incoming search terms: